Search Results

This paper presents the results of investigations that were carried out on a single-cylinder spray-guided direct injection engine. The effects of injection pressures of up to 1000 bar on combustion and emissions at the stability limit of stratified load are presented. It is known that at low engine speeds, problems in mixture preparation occur due to insufficient in-cylinder motion at higher loads in stratified charge operation. Additionally, adverse effects appear at high engine speeds due to limited time for vaporization and mixture formation. Therefore, investigations at various engine speeds ranging from 2000 to 4000 rpm were performed. As a baseline, a production multihole injector is compared with an injector that has been specially adapted for higher injection pressures.

Understanding the processes regarding fuel injection, vaporization and combustion during cold start is very important in order to reduce the HC-emission of gasoline engines. To learn more about the cold engine start-up process an experimental study on a 4.2 liter eight cylinder engine with gasoline direct injection was carried out. Parameters such as injection and ignition timing as well as the injection quantity were varied to get information about their effect on the combustion process and speed rise. Especially during engine run-up it is important to investigate every subsequent combustion. Therefore the engine was equipped with high pressure indication in each cylinder. The transient pressures and the instantaneous crankshaft speed of the engine were recorded by means of an indication system. Additionally a fast response flame ionization detector (FRFID) was applied to measure the transient HC-emissions during the first cycles of the engine.

Unstable combustion and high cyclic variations of the in-cylinder pressure associated with low engine running smoothness and high emissions are mainly caused by cyclic variations of the fresh charge composition, the variability of the ignition and the fuel mass. These parameters affect the inflammation, the burn rate and thus the whole combustion process. In this paper, the effects of fluctuating fuel mass on the combustion behavior are shown. Small two-stroke engines require special measuring and testing equipment, especially for measuring the fuel consumption at very low fuel flow rates as well as very low fuel supply pressures. To realize a cycle-resolved measurement of the injected fuel mass, fuel consumption measurement with high resolution and high dynamic response is not enough for this application.

A promising approach for reducing both NOx- and particulate matter emissions with low fuel consumption is the so called homogeneous charge compression ignition (HCCI) combustion process. Single-cylinder engine tests were carried out to assess the influence of several parameters on the HCCI combustion. The experiments were performed both with port fuel injection (PFI) and with direct injection (DI) under various compression ratios, intake air temperatures and EGR-rates. Special emphasis was put on the fuel composition by using different gasoline and diesel fuels as well as n-heptane. Besides engine out emissions (CO2, CO, NO, O2, HC, soot) and in-cylinder pressure indication for burning process analysis, the combustion itself was visualised using an optical probe.

The spray propagation and disintegration is investigated in a pressure chamber. With Particle Image Velocimetry the direction and velocity of both, fuel droplets and induced gas flow are detected. By means of shadow photographs the spray cone geometry is visualized. To verify the predictions made of the measurements mentioned above and to rate the quality of the tuning of the parameters in-cylinder gas flow, injection pressure, position of Injector and position of spark plug under real engine conditions, a fast gas sampling valve is used in three different engines. The in-cylinder gas temperature and the soot concentration are measured crank angle resolved by means of the Two-Colour-Method in a 1-cylinder GDI-engine. The soot concentration and temperature show the influence of the injection pressure on emissions like soot and nitric oxide.

The hollow cone spray from a high pressure outward opening nozzle was investigated inside a pressure vessel by means of particle image velocimetry (PIV). The flow velocities of the air outside the spray were measured via PIV in combination with fluorescent seeding particles and optical filters. The high pressure piezo electric injector has an annular nozzle to provide a hollow cone spray with an angle of about 90°. During injection a very strong and stable vortex structure is induced by the fuel spray. Besides the general spray/air interaction, the investigation of double and triple fuel injections was the main focus of this study.

In gasoline direct injection engines with stratified-combustion strategies only a short time is available for mixture preparation. Therefore, investigations are carried out to evaluate the influence of high injection pressure up to 50 MPa in order to optimize the mixture preparation. Two types of multi-hole injectors are analyzed in a pressure vessel under various pressure and temperature conditions. Laser light sheet visualization technique is applied in order to determine spray characteristics like shape, angle, penetration depth and spray width. To determine the velocity of the air surrounding the spray, a PIV (Particle Image Velocimetry) measurement technique is used. Droplet sizes and velocities are measured with a Phase Doppler Anemometer (PDA) in different positions in the spray center and at the spray edge. Spray visualization experiments show the influence of evaporation on spray propagation at higher temperatures.