Search Results

The study of spray-wall interaction is of great importance to understand the dynamics that occur during fuel impingement onto the chamber wall or piston surfaces in internal combustion engines. It is found that the maximum spreading length of an impinged droplet can provide a quantitative estimation of heat transfer and energy transformation for spray-wall interaction. Furthermore, it influences the air-fuel mixing and hydrocarbon and particle emissions at combusting conditions. In this paper, an analytical model of a single diesel droplet impinging on the wall with different inclined angles (α) is developed in terms of βm (dimensionless maximum spreading length, the ratio of maximum spreading length to initial droplet diameter) to understand the detailed impinging dynamic process.

An experimental study and analysis was conducted to investigate cold start robustness of an ethanol flex-fuel spark ignition (SI) direct injection (DI) engine. Cold starting with ethanol fuel blends is a known challenge due to the fuel characteristics. The program was performed to investigate strategies to reduce the enrichment requirements for the first firing cycle during a cold start. In this study a single-cylinder SIDI research engine was used to investigate gasoline and E85 fuels which were tested with three piston configurations (CR11F, CR11B, CR15.5B - which includes changes in compression ratio and piston geometry), at three intake cam positions (95, 110, 125 °aTDC), and two fuel pressures (low: 0.4 MPa and high: 3.0 MPa) at 25°C±1°C engine and air temperature, for the first cycle of an engine start.

The necessity to study spray-wall interaction in internal combustion engines is driven by the evidence that fuel sprays impinge on chamber and piston surfaces resulting in the formation of wall films. This, in turn, may influence the air-fuel mixing and increase the hydrocarbon and particulate matter emissions. This work reports an experimental and numerical study on spray-wall impingement and liquid film formation in a constant volume combustion vessel. Diesel and n-heptane were selected as test fuels and injected from a side-mounted single-hole diesel injector at injection pressures of 120, 150, and 180 MPa on a flat transparent window. Ambient and plate temperatures were set at 423 K, the fuel temperature at 363 K, and the ambient densities at 14.8, 22.8, and 30 kg/m3. Simultaneous Mie scattering and schlieren imaging were carried out in the experiment to perform a visual tracking of the spray-wall interaction process from different perspectives.

Water spray characterization of a multi-hole injector under pressures and temperatures representative of engine-relevant conditions was investigated for naturally aspirated and boosted engine conditions. Experiments were conducted in an optically accessible pressure vessel using a high-speed Schlieren imaging to visualize the transient water spray. The experimental conditions included a range of injection pressures of 34, 68, and 102 bar and ambient temperatures of 30 - 200°C, which includes flash-boiling and non-flash-boiling conditions. Transient spray tip penetration and spray angle were characterized via image processing of raw Schlieren images using Matlab code. The CONVERGE CFD software was used to simulate the water spray obtained experimentally in the vessel. CFD parameters were tuned and validated against the experimental results of spray profile and spray tip penetration measured in the combustion vessel (CV).

High injection pressure impinging spray experiments and modeling were performed under simulated diesel engine conditions (pressure and density) at ambient temperature. A spray impinged normal to a small crown in the bowl of a simulated piston. High speed photography was used in the constant volume bomb to examine the effect of impingement on fuel mixing. The spray model which includes drop breakup, coalescence, impingement, and vaporization effects was used to predict fuel mixing in the bomb. The spray distributions predicted by the model are compared to the photographs obtained in the bomb.

Under low-temperature combustion for the high fuel efficiency and low emissions achievement, the fuel impingement often occurs in diesel engines with direct injection especially for a short distance between the injector and piston head/cylinder wall. Spray impingement plays an important role in the mixing-controlled combustion phase since it affects the air-fuel mixing rate through the disrupted event by the impingement. However, the degree of air entrainment into the spray is hard to be directly evaluated. Since the high spray expansion rate could allow more opportunity for fuel to mix with air, in this study, the expansion rate of impinged flame is quantified and compared with the spray expansion rate under non-vaporizing conditions. The experiments were conducted in a constant volume combustion chamber with an ambient density of 22.8 kg/m3 and the injection pressure of 150 MPa.

The fuel spray impingement on the piston head and/or chamber often occurs in compact IC engines. The impingement plays one of the key roles in combustion because it affects the air-fuel mixing process. In this study, the impinged combustion has been experimentally investigated to understand the mechanism and dynamics of flame-wall interaction. The experiments were performed in a constant volume combustion chamber over a wide range of ambient conditions. The ambient temperature was varied from 800 K to 1000 K and ambient gas oxygen was varied from 15% to 21%. Diesel fuel was injected with an injection pressure of 150 MPa into ambient gas at a density of 22.8 kg/m3. The natural luminosity technique was applied in the experiments to explore the impinged combustion process. High-speed images were taken using a high-speed camera from two different views (bottom and side). An in-house Matlab program was used to post-process the images.

A computer model was used to study the impingement of sprays on walls. The spray model accounts for the effects of drop breakup, drop collision and coalescence, and the effect of drops on the gas turbulence. These effects have been shown to be important in high-pressure sprays where breakup of the liquid yields a core region near the nozzle containing large drops. A new submodel was developed to describe the spray/wall interaction process. The model uses an analogy with the oblique impact on a wall of liquid jets. Following impact, the trajectory of a drop is specified to be tangent to the wall surface. The computations were compared with recent endoscope pictures of engine sprays impinging on a piston bowl and also with constant-volume-bomb measurements of spray shape and penetration. Predictions of the effect of engine swirl, ambient gas pressure (density), wall inclination angle and the distance from the nozzle to the wall, were in good qualitative agreement with the experiments.