Search Results

The effects of imaging system resolution and laser sheet thickness on the measurement of the Batchelor scale were investigated in a single-cylinder optical engine. The Batchelor scale was determined by fitting a model spectrum to the dissipation spectrum that was obtained from fuel tracer planar laser-induced fluorescence (PLIF) images of the in-cylinder scalar field. The imaging system resolution was quantified by measuring the step-response function; the scanning knife edge technique was used to measure the 10-90% clip width of the laser sheet. In these experiments, the spatial resolution varied from a native resolution of 32.0 μm to 137.4 μm, and the laser sheet thickness ranged from 108 μm to 707 μm. Thus, the overall resolution of the imaging system was made to vary by approximately a factor of four in the in-plane dimension and a factor of six in the out-of-plane dimension.

High resolution planar laser-induced fluorescence (PLIF) measurements were performed in an optically accessible internal combustion (IC) engine to investigate the behavior of scalar dissipation and the fine-scale structures of the turbulent scalar field. The fluorescent tracer fluorobenzene was doped into one of the two intake streams and nitrogen was used as the carrier gas to permit high signal-to-noise ratio fluorescence measurements without oxygen quenching effects. The resulting two-dimensional images allowed for an analysis of the structural detail of the scalar and scalar dissipation fields defined by the mixing of the two adjacent intake streams. High levels of scalar dissipation were found to be located within convoluted, sheet-like structures in accordance with previous studies. The fluorescence data, which were acquired during the intake stroke, were also used to examine the scalar energy and dissipation spectra.

The ability to make fully resolved turbulent scalar field measurements has been demonstrated in an internal combustion engine using one-dimensional fluorobenzene fluorescence measurements. Data were acquired during the intake stroke in a motored engine that had been modified such that each intake valve was fed independently, and one of the two intake streams was seeded with the fluorescent tracer. The scalar energy spectra displayed a significant inertial subrange that had a −5/3 wavenumber power dependence. The scalar dissipation spectra were found to extend in the high-wavenumber regime, to where the magnitude was more than two decades below the peak value, which indicates that for all practical purposes the measurements faithfully represent all of the scalar dissipation in the flow.

In-cylinder velocity measurements were acquired in a two-valve, single-cylinder research engine to study the bulk fluid motion and small-scale turbulence. Different port geometries (two), different port orientations (two) and both shrouded and non-shrouded intake valves were tested to vary the intake-generated flow. Tests were performed at engine speeds of 300, 600, 900 and 1200 RPM with an atmospheric intake pressure. Prior to testing on the engine, the different head configurations were tested on a steady flow bench. Particle image velocimetry data were taken on a single plane, parallel to the piston surface, in the engine using both a low magnification to characterize the large-scale flow phenomena, and a high magnification to characterize the turbulence field. The low-magnification results showed that the swirl center location was relatively insensitive to engine speed, but did change position throughout the cycle.

A novel algebraic similarity model for subgrid scalar dissipation rate has been developed as part of the Large Eddy Simulation (LES) package KIVA3V-LES for diesel engine study. The model is proposed from an a priori study using Direct Numerical Simulation (DNS) of forced isotropic turbulence. In the a posteriori test, fully resolved turbulent passive scalar field measurements are used to validate the model in actual engine flows. For reason of the length limit by SAE and the specific interest in engine applications, only a prior test and a posteriori test in engine flows are included in this paper. A posteriori tests in isotropic cube flow, turbulent round jet and flame cases will be presented in separate papers. An engine LES simulation of multi consecutive cycles was performed in this study.

The current work investigates the in-cylinder mixing of a fluorescent tracer species inducted into the engine through a small-diameter tube mounted along the inner port wall and the remaining inlet stream in a small-bore utility engine. Planar laser-induced fluorescence (PLIF) measurements were acquired on a single plane, parallel to and approximately 4 mm below the cylinder head deck, throughout the intake and compression strokes. The data were analyzed to qualitatively and quantitatively describe the evolution of the mixture stratification. The highest degree of stratification in the mean field was observed at a timing of 90 crank angle (CA) degrees after top dead center (aTDC) of the intake stroke, which corresponds closely to the point of maximum intake valve lift (105 CA degrees aTDC).

High-resolution planar laser-induced fluorescence (PLIF) measurements were performed on the scalar field in an optical engine. The measurements were of sufficient resolution to fully resolve all of the length scales of the flow field through the full cycle. The scalar dissipation spectrum was calculated, and by fitting the results to a model turbulent spectrum the Batchelor scale of the turbulent flow was estimated. The scalar inhomogeneity was introduced by a low-momentum gas jet injection. A consistent trend was observed in all data; the Batchelor scale showed a minimum value at top dead center (TDC) and was nearly symmetric about TDC. Increasing the engine speed resulted in a decrease of the Batchelor scale, and the presence of a shroud on the intake valve, which increased the turbulence intensity, also reduced the Batchelor scale. The effect of the shrouded valve was less significant compared to the effect of engine speed.

High frame rate particle image velocimetry (PIV) measurements were performed in a motored engine at speeds of 600 and 1200 rpm under both throttled and unthrottled conditions. Data were acquired at 1 kHz throughout the entire engine cycle, allowing the temporal and spatial evolution of the flow to be observed. The data were both temporally and spatially filtered to study the turbulent flowfield. The mean (over the spatial domain) kinetic energy of the high-pass filtered data, and its evolution with cutoff frequency or length, was used to quantitatively compare differences between operating conditions and different cycles at the same condition. The difference in fluctuation kinetic energy, when normalized, between different operating conditions was found to be comparable to the difference between cycles. A comparison between spatially and temporally filtered data at the same level of fluctuation kinetic energy was performed.

Valve deactivation followed by multiple compression-expansion strokes was employed to remove intake-generated turbulence from the bulk gas in an internal combustion engine. The result was a nearly quiescent flowfield that retains the same time-varying geometry and, to a first approximation, thermodynamic conditions as a standard engine. Mass loss, and more significantly heat loss were found to contribute to a reduction in the peak cylinder pressure in the cycle following two compression-expansion strokes. The reduction of the turbulence was verified both computationally and by performing premixed combustion studies. Mixing studies of both liquid spray jets and gaseous jets were performed. Laser-induced fluorescence images of high spatial resolution and signal-to-noise ratio were acquired, allowing the calculation of the two in-plane components of the scalar dissipation rate.