Search Results

An experimental investigation was conducted to explore the impact in-cylinder pressure oscillations have on piston heat transfer. Two fast-response surface thermocouples embedded in the piston top measured transient temperature and a commercial wireless telemetry system was used to transmit thermocouple signals from the moving piston. Measurements were made in a light-duty single-cylinder research engine operated under low temperature combustion regimes including Homogeneous Charge Compression Ignition (HCCI) and Reactivity Controlled Compression Ignition (RCCI) and Conventional Diesel (CDC). The HCCI data showed a correlated trend of higher heat transfer with increased pressure oscillation strength, while the RCCI and CDC data did not. An extensive HCCI data set was acquired. The heat transfer rate - when corrected for differences in cylinder pressure and gas temperature - was found to positively correlate with increased pressure oscillations.

High resolution planar laser-induced fluorescence (PLIF) measurements were performed in an optically accessible internal combustion (IC) engine to investigate the behavior of scalar dissipation and the fine-scale structures of the turbulent scalar field. The fluorescent tracer fluorobenzene was doped into one of the two intake streams and nitrogen was used as the carrier gas to permit high signal-to-noise ratio fluorescence measurements without oxygen quenching effects. The resulting two-dimensional images allowed for an analysis of the structural detail of the scalar and scalar dissipation fields defined by the mixing of the two adjacent intake streams. High levels of scalar dissipation were found to be located within convoluted, sheet-like structures in accordance with previous studies. The fluorescence data, which were acquired during the intake stroke, were also used to examine the scalar energy and dissipation spectra.

The ability to make fully resolved turbulent scalar field measurements has been demonstrated in an internal combustion engine using one-dimensional fluorobenzene fluorescence measurements. Data were acquired during the intake stroke in a motored engine that had been modified such that each intake valve was fed independently, and one of the two intake streams was seeded with the fluorescent tracer. The scalar energy spectra displayed a significant inertial subrange that had a −5/3 wavenumber power dependence. The scalar dissipation spectra were found to extend in the high-wavenumber regime, to where the magnitude was more than two decades below the peak value, which indicates that for all practical purposes the measurements faithfully represent all of the scalar dissipation in the flow.

The contribution of fuel adsorption in engine oil and its subsequent desorption following combustion to the engine-out hydrocarbon (HC) emissions of a spark-ignited, air-cooled, V-twin utility engine was studied by comparing steady state and cycle-resolved HC emission measurements from operation with a standard full-blend gasoline, and with propane, which has a low solubility in oil. Experiments were performed at two speeds and three loads, and for different mean crankcase pressures. The crankcase pressure was found to impact the HC emissions, presumably through the ringpack mechanism, which was largely unaltered by the different fuels. The average and cycle-resolved HC emissions were found to be in good agreement, both qualitatively and quantitatively, for the two fuels. Further, the two fuels showed the same response to changes in the crankcase pressure. The solubility of propane in the oil is approximately an order of magnitude lower than for gasoline.

To experimentally investigate evaporating sprays under conditions experienced in high speed direct-injection (HSDI) diesel engines, the exciplex LIF technique with the TMPD / naphthalene dopant system was applied in a combustion-type constant-volume spray chamber. The chamber allows spark ignition of a slightly rich C2H2-air mixture, and subsequent fuel injection into the high temperature and pressure products. A detailed set of calibration experiments has been performed in order to quantify the TMPD fluorescence signal. It has been demonstrated that the TMPD fluorescence intensity is directly proportional to concentration, is independent of the chamber pressure, and was not sensitive to quenching by either water vapor or carbon dioxide. Therefore, the temperature dependence of the TMPD fluorescence was the only correction factor required for quantitative measurements. Using a dual heated-jet experiment, the temperature dependence of TMPD fluorescence up to 1000 K was measured.

A simple model to simulate cycle-by-cycle variation that is suitable for use in Monte-Carlo approaches has been developed and validated with a wide range of experimental data. The model is intended to be diagnostic rather than predictive in nature, with a goal of providing realistic in-cylinder pressures. The individual-cycle cumulative rate of heat release was curve fit with a four-parameter Wiebe function. It was found that the distribution of the Wiebe b-parameter was quite small, so its value was obtained from the ensemble-averaged condition. The remaining three Wiebe function parameters, θig, θcomb and m were found to be distributed over a moderate range, and were linearly correlated to each other. Using the cumulative density function of θig, and the linear fit of θcomb and m to θig, with a random component added, a Monte-Carlo scheme was developed.

The objective of this work is to compare and contrast standard metrics that are used to quantify engine knock phenomena. Several methods found in the literature were investigated, and the fundamental bases for the methods were elucidated. A new knock onset metric was developed and compared to the commonly used threshold value exceeded metric. The standard knock intensity metrics were categorized based on the underlying signal (pressure, heat release), domain of analysis (time or frequency), and the calculation method (single-valued or integral). Each category was evaluated based on the fundamental advantages and disadvantages of that category. Single-value methods were found to be inadequate because they are prone to biases due to wave interference and beating. Heat release-based metrics were found to be redundant and be based on flawed assumptions.

The light-medium load operating range (4-7 bar net IMEP) presents many challenges for advanced low temperature combustion strategies utilizing low cetane fuels (specifically, 87-octane gasoline) in light-duty, high-speed engines. The overly lean overall air-fuel ratio (Φ≺0.4) sometimes requires unrealistically high inlet temperatures and/or high inlet boost conditions to initiate autoignition at engine speeds in excess of 1500 RPM. The objective of this work is to identify and quantify the effects of variation in input parameters on overall engine operation. Input parameters including inlet temperature, inlet pressure, injection timing/duration, injection pressure, and engine speed were varied in a ~0.5L single-cylinder engine based on a production General Motors 1.9L 4-cylinder high-speed diesel engine.

Schlieren visualization was performed to investigate hydrogen injection into a quiescent chamber. The injection pressures investigated were 52 and 104 bar, and the chamber density ranged from 1.15 to 12.8 kg/m3, giving rise to underexpanded jets for all conditions. The expansion waves outside the nozzle were clearly visible with hydrogen, and the effect was confirmed with studies of nitrogen injected into a nitrogen environment. The distance between the expansion wave fronts was found to scale directly with the ratio of the exit pressure to the chamber pressure. The jet tip penetration rate was measured and was found to increase with injection pressure, and decrease with chamber density as expected. A mass- and momentum-preserving scheme was developed to relate the underexpanded jet to a subsonic jet of larger diameter.

Valve deactivation followed by multiple compression-expansion strokes was employed to remove intake-generated turbulence from the bulk gas in an internal combustion engine. The result was a nearly quiescent flowfield that retains the same time-varying geometry and, to a first approximation, thermodynamic conditions as a standard engine. Mass loss, and more significantly heat loss were found to contribute to a reduction in the peak cylinder pressure in the cycle following two compression-expansion strokes. The reduction of the turbulence was verified both computationally and by performing premixed combustion studies. Mixing studies of both liquid spray jets and gaseous jets were performed. Laser-induced fluorescence images of high spatial resolution and signal-to-noise ratio were acquired, allowing the calculation of the two in-plane components of the scalar dissipation rate.

The light-medium load operating regime (4-8 bar net IMEP) presents many challenges for advanced low temperature combustion strategies (e.g. HCCI, PPC) in light-duty, high speed engines. In this operating regime, lean global equivalence ratios (Φ<0.4) present challenges with respect to autoignition of gasoline-like fuels. Considering this intake temperature sensitivity, the objective of this work was to investigate, both experimentally and computationally, gasoline compression ignition (GCI) combustion operating sensitivity to inlet swirl ratio (Rs) variations when using a single fuel (87-octane gasoline) in a 0.475-liter single-cylinder engine based on a production GM 1.9-liter high speed diesel engine. For the first part of this investigation, an experimental matrix was developed to determine how changing inlet swirl affected GCI operation at various fixed load and engine speed operating conditions (4 and 8 bar net IMEP; 1300 and 2000 RPM).