Search Results

The upcoming Bharat Stage VI (BS VI) emission legislation has put enormous pressure on the future of small diesel engines which are widely used in the Indian market. The present work investigates the emission reduction potential of a common rail direct injection single cylinder diesel engine by adopting a holistic approach of lowering the compression ratio, boosting the intake air and down-speeding the engine. Experimental investigations were conducted across the entire operating map of a mass-production, light-duty diesel engine to examine the benefits of the proposed approach and the results are quantified for the modified Indian drive cycle (MIDC). By reducing the compression ratio from 18:1 to 14:1, the oxides of nitrogen (NOx) and soot emissions are reduced by 40% and 75% respectively. However, a significant penalty in fuel economy, unburned hydrocarbon (HC) and carbon monoxide (CO) emissions are observed with the reduced compression ratio.

Adopting a low compression ratio (LCR) is a viable approach to meet the stringent emission regulations since it can simultaneously reduce the oxides of nitrogen (NOx) and particulate matter (PM) emissions. However, significant shortcomings with the LCR approach include higher unburned hydrocarbon (HC) and carbon monoxide (CO) emissions and fuel economy penalties. Further, poor combustion stability of LCR engines at cold ambient and part load conditions may worsen the transient emission characteristics, which are least explored in the literature. In the present work, the effects of implementing the low compression ratio (LCR) approach in a mass-production light-duty vehicle powered by a single-cylinder diesel engine are investigated with a major focus on transient emission characteristics.

Owing to a high power-to-weight ratio, mini internal combustion engine is used in propelling an unmanned air vehicle. In comparison to the performance characteristics, the investigations on the combustion aspects of mini engines are scanty. This investigation concerns study of the combustion process of a mini engine and its variability. For this purpose, the experimental cylinder pressure histories were obtained on a laboratory set-up of a 7.45 cm3 capacity mini engine. The analyses of experimental data at different throttle settings reveal that there existed a varied range of rich and lean misfiring limits around a reference equivalence ratio that corresponds to the respective maximum indicated mean effective pressure. At the limiting equivalence ratios, cylinder pressure measurements showed a high degree of cycle-to-cycle variations. In some cases, a slow combustion or misfiring event preceded a rapid combustion.

To comply with the stringent future emission mandates of light-duty diesel engines, it is essential to deploy a suitable combination of emission control devices like diesel oxidation catalyst (DOC), diesel particulate filter (DPF) and DeNOx converter (LNT or SCR). Arriving at optimum size and layout of these emission control devices for a particular engine through experiments is both time and cost-intensive. Thus, it becomes important to develop suitable well-tuned simulation models that can be helpful to optimize individual emission control devices as well as arrive at an optimal layout for achieving higher conversion efficiency at a minimal cost. Towards this objective, the present work intends to develop a one-dimensional Exhaust After Treatment Devices (EATD) model using a commercial code. The model parameters are fine-tuned based on experimental data. The EATD model is then validated with experiment data that are not used for tuning the model.

In a direct-injection (DI) engine, charge motion and mixture preparation are among the most important factors deciding the performance and emissions. This work was focused on studying the effect of injector positioning on fuel-air mixture preparation and fuel impingement on in-cylinder surfaces during the homogeneous mode of operation in a naturally aspirated, small bore, 0.2 l, light-duty, air-cooled, four-stroke, spark-ignition engine modified to operate under the DI mode. A commercially available, six-hole, solenoid-operated injector was used. Two injector locations were identified based on the availability of the space on the cylinder head. One location yielded the spray-guided (SG) configuration, with one of the spray plumes targeted towards the spark plug. In the second location, the spray plumes were targeted towards the piston top in a wall-guided (WG) configuration so as to minimize the impingement of fuel on the liner.

In this work, a 7.45 cc capacity glow plug based two-stroke engine for mini aircraft applications was evaluated for its performance, emissions and combustion. It uses a fuel containing 65% methanol, 25% castor oil and 10% nitromethane by volume. Since test rigs are not readily available for such small engines, a reaction type test bed with low friction linear and rolling element bearings was developed and used successfully. The propeller of the engine acted as the load and also the flywheel. Pressure time diagrams were recorded using a small piezoelectric pressure transducer. Tests were conducted at two different throttle positions and at various equivalence ratios. The brake thermal efficiency was generally in the range of 4 to 17.5% depending on the equivalence ratio and throttle position. IMEP was between 2 and 4 bar. It was found that only a part of the castor oil that was supplied participated in the combustion process.

A novel, fully mechanical, simple, compact and cost effective variable valve timing system for two-wheeler application was developed. The details of the system and the performance are discussed. The system uses flyweights to exert a force on a cam, which floats on a shaft against a spring. The movement of the cam is axial and rotational due helical groves on the shaft. The system could start retarding the cam phasing after a predetermined speed. The system when implemented on a small scooter engine of 125 cc resulted in an increase in the volumetric efficiency at low speeds by 8%. The torque was improved by 10%. There was a reduction in the fuel consumption due to reduced throttling losses and leaner mixtures. When the system was implemented on a two-wheeler and tested on a chassis dynamometer on the Indian Driving Cycle a reduction in fuel consumption of 5% was noted. The emissions were also within limits.

Use of vegetable oils in diesel engines results in increased smoke and reduced brake thermal efficiency. Dual fuel engines can use a wide range of fuels and yet operate with low smoke emissions and high thermal efficiency. In this work, a single cylinder diesel engine was converted to use vegetable oil (Jatropha oil) as the pilot fuel and methanol as the inducted primary fuel. Tests were conducted at 1500 rev/min and full load. Different quantities of methanol and Jatropha oil were used. Results of experiments with diesel as the pilot fuel and methanol as the primary fuel were used for comparison. Brake thermal efficiency increased in the dual fuel mode when both Jatropha oil and diesel were used as pilot fuels. The maximum brake thermal efficiency was 30.6% with Jatropha oil and 32.8% with diesel. Smoke was drastically reduced from 4.4 BSU with pure Jatropha oil operation to 1.6 BSU in the dual fuel mode.

A single cylinder, direct injection diesel engine was run on water diesel emulsion at a constant speed of 1500 rpm under variable load conditions. Water to diesel ratio of 0.4 on the mass basis was used. Tests indicated a considerable reduction in smoke and NO levels. This was accompanied by an increase in brake thermal efficiency at high outputs. HC & CO levels, ignition delay and rate of pressure rise went up. The heat release rate in the premixed burn period was higher. When the oxygen concentration in the intake air was enhanced in steps up to 25% along with the use of water diesel emulsion, the brake thermal efficiency was improved and there was a further reduction in the smoke level. HC and CO levels also dropped. NO emission went up due to increased temperature and oxygen availability. An oxygen concentration of 24% by volume was optimal as the NO levels were near about base diesel values.

Setting the correct valve timing and lift based on the operating speed will be the key to achieving good volumetric efficiency and torque. Continuously variable valve timing systems are the best choice but are too expensive. In this work a novel two stage variable valve actuation system was conceived and developed for a small single cylinder three wheeler spark ignition engine. The constraints were space, cost and complexity. The developed system uses one cam for low speeds and another cam that has a higher lift and duration for high speeds. The shift between the cams occurs through the mechanism even as the engine runs by the operation of a stepper motor which can be connected to the engine controller. A one dimensional simulation model validated with experimental data was used to predict the suitable valve timings and lifts in low and high speed ranges. Two profiles were then selected.

Supercharging a single-cylinder diesel engine has proved to be a viable methodology to reduce engine-out emissions and increase full-load torque and power. The increased air availability of the supercharger (SC) system helps to inject more fuel quantity that can improve the engine's full-load brake mean effective pressure (BMEP) without elevating soot emissions. However, the increased inlet temperature of the boosted air and the availability of excess oxygen can pose significant challenges to contain oxides of nitrogen (NOx) emissions. Hence, it is important to investigate the potential NOx reduction options in supercharged diesel engines. In the present work, the potential of low-pressure exhaust gas recirculation (LP EGR) was evaluated in a single-cylinder supercharged diesel engine for its benefits in NOx emission reduction and impact on other criteria emissions and brake specific fuel consumption (BSFC).

It is well established that reducing the compression ratio (CR) of a diesel engine leads to a significant increase in hydrocarbon (HC) and carbon monoxide (CO) emissions, especially in cold and transient conditions. Hence, it is essential to find new strategies to reduce the HC and CO emissions of a low compression ratio (LCR) diesel engine in transient conditions. In the present work, a detailed evaluation of different warm-up technologies was conducted for their effects on transient emissions characteristics of a single-cylinder naturally aspirated LCR diesel engine. For this purpose, the engine was coupled to an instrumented transient engine dynamometer setup. A transient cycle of 160 seconds with starting, idling, speed ramp-up and load ramp-up was defined, and the engine was run in automatic mode by the dynamometer. The experiments were conducted by overnight soaking the engine at a specified temperature of 25 deg.C.

Mass-production single-cylinder engines are generally not turbocharged due to pulsated exhaust flow. Hence, about one-third of the fuel chemical energy is wasted in the engine exhaust. To extract the exhaust energy and boost the single-cylinder engines, a novel supercharging with a turbo-compounding strategy is proposed in the present work, wherein an impulse turbine extracts energy from the pulsated exhaust gas flow. Employing an impulse turbine for a vehicular application, especially on a single-cylinder engine, has never been commercially attempted. Hence, the design of the impulse turbine assumes higher importance. A nozzle, designed as a stator part of the impulse turbine and placed at the exhaust port to accelerate the flow velocity, was included as part of the layout in the present work. The layout was analyzed using the commercial software AVL BOOST. Different nozzle exit diameters were considered to analyze their effect on the exhaust back pressure and engine performance.

Single-cylinder engines in mass production are generally not turbocharged due to the pulsated and intermittent exhaust gas flow into the turbocharger and the phase lag between the intake and exhaust stroke. The present work proposes a novel approach of decoupling the turbine and the compressor and coupling them separately to the engine to address these limitations. An impulse turbine is chosen for this application to extract energy during the pulsated exhaust flow. Commercially available AVL BOOST software was used to estimate the overall engine performance improvement of the proposed novel approach compared to the base naturally aspirated (NA) engine. Two different impulse turbine layouts were analyzed, one without an exhaust plenum and the second layout having an exhaust plenum before the power turbine. The merits and limitations of both layouts are compared in the present study.

A diesel engine was operated with karanja oil, bio-diesel obtained from karanja oil (BDK) and diesel as pilot fuels while LPG was used as primary fuel. LPG supply was varied from zero to the maximum value that the engine could tolerate. The engine output was kept at different constant levels of 25%, 50%, 75% and 100% of full load. The thermal efficiency improved at high loads. Smoke level was reduced drastically at all loads. CO and HC levels were reduced at full load. There was a slight increase in the NO level. Combustion parameters indicated an increase in the ignition delay. Peak pressure and rate of pressure rise were not unfavorably affected. There was an increase in the peak heat release rate with LPG induction. The amount of LPG that could be tolerated with out knock at full load was 49%, 53% and 61% on energy basis with karanja oil, BDK and diesel as pilots.

Short-circuiting of the fuel air mixture during scavenging is the main reason for high fuel consumption and hydrocarbon (HC) emissions in two-stroke SI engines. Though direct injection of the fuel after the closure of ports has advantages, it is costly and complex. In this work, in a 2S-SI, single cylinder, automotive engine, LPG (liquefied Petroleum Gas) was injected through the boost port to reduce short-circuiting losses. A fuel injector was located on one of the boost ports and the air alone was fed through the other transfer and boost ports for scavenging. Experiments were done at 25% and 70% throttle openings with different injection timings and optimal spark timing at 3000 rpm. Boost port injection (BPI) of LPG reduced HC emissions at all conditions as compared to LPG-MI (Manifold Injection). Particularly significant reductions were seen at high throttle conditions and rich mixtures. HC reductions with BPI were 19% and 25% as compared to LPG-MI and gasoline-MI respectively.

This experimental study was aimed at improving a two-stroke S.I engine by injecting gasoline with air assistance through the cylinder barrel. Experimentally obtained performance and emission parameters of the engine at 25% and 100% throttle positions were analyzed at 3000 rpm. The timing of air assisted injection was optimized at 25% throttle and 3000 rpm. The performance and emissions of the engine were compared with those obtained with an optimized manifold injection system. In all cases the best spark timing was used. At 25% throttle although the thermal efficiency was increased only slightly, there was a significant reduction in HC emissions to 6.63 g/kW-h with cylinder barrel injection from 10.69 g/kW-h with manifold injection due to reduced short circuiting of the fuel. There was a reduction in NO emissions as well with cylinder barrel injection. Comparisons were made at the point of highest thermal efficiency at 100% throttle also.

In a dual fuel engine a primary fuel that is generally a gas is mixed with air, compressed and ignited by a small pilot- spray of diesel as in a diesel engine. Dual fuel engines generally suffer from the problem of lower brake power and lower peak engine cylinder pressure due to lower volumetric efficiency, although an improvement in brake specific energy consumption is observed compared to pure diesel mode. Results indicate that with an increase in percentage of CNG substitution the brake power decreases. The exhaust gas temperature and peak cylinder pressure also decrease. The rate of pressure rise is higher at lower engine speeds (1100, 1400 rev/min), although at 1700 and 2000 rev/min it is lower. The delay period throughout the engine speed shows an increasing trend. The coefficient of variation is also higher throughout the engine speeds and shows an increasing trend. The brake specific energy consumption is lower at 1100, 1400 and 1700 rev/min and at 2000 rev/min it is higher.

The increasing use of natural gas as a vehicle fuel has generated considerable research activity to characterize the performance of engines utilizing this fuel. A light duty prechamber diesel engine was run under naturally aspirated and turbocharged CNG- Diesel dual fuel mode at four engine speeds 1100, 1400, 1700 and 2000 rpm. The maximum percentage of CNG substitution continues up to the engine knock limited power. The experimental results indicate a fall in brake power under naturally aspirated CNG-Diesel dual fuel mode compared to neat diesel operation. It was due to decrease in volumetric efficiency and slower combustion. Although turbocharged dual fuel operation shows an increase in brake power as well as an improvement in brake specific energy consumption as it provides a better air/fuel mixing and improves the homogeneous natural gas/air charge.

In many Asian countries a significant automobile market share is held by two and three wheelers. Generally, cost and simplicity considerations limit the performance and emission levels of small engines. Methanol is an excellent alternative fuel for SI engines due to its high-octane number, high flame speed, presence of oxygen in its molecule and thus can be used to enhance the performance of small engines. However, use of neat methanol in SI engines poses constraints due to low energy density and poor vaporization characteristics. Also, the effectiveness of methanol as a fuel has still to be thoroughly investigated in small-bore SI engines in order to assess its potential. In this work, a small-bore 200cc three-wheeler automotive engine was modified to operate in the port fuel injection mode with neat methanol as the fuel.