Search Results

This paper presents a compound combustion technology of Premixed Combustion and “Lean Diffusion Combustion” for realizing the concept of HCCI combustion in a D I diesel engine. The premixed combustion is achieved by the technology of multi-pulse fuel injection. The start of pulse injection, injection-pulse number, injection period of each pulse and the dwell time between the injection pulses are controlled. The objective of controlling the pulse injection is to limit the spray penetration of the pulse injection so that the fuel will not impinge on the cylinder liner, and to enhance the mixing rate of each fuel parcel by promoting the disturbance to the fuel parcels. The last or main injection pulse is set around TDC. A flash mixing technology is developed from the development of a so-called BUMP combustion chamber, which is designed with some special bump rings.

A numerical simulation was performed to investigate the pilot ignited natural gas combustion process in a direct injection natural gas engine. Various mixture distribution characteristics were compared in terms of the evolution of mixture equivalent ratio distributions and mixture concentration stratifications around top dead center (TDC). Based on above, the pilot injections were specially designed to investigate ignition core formation and its effects on natural gas combustion process. The result shows that pilot ignition sites have great impacts on pilot fuel ignition process and natural gas combustion process. The pilot ignition site on the region with rich NG/Air mixture is disadvantageous to the pilot fuel ignition due to a lack of oxygen, which is not beneficial to ignition core formation.

Combustion control strategy for high efficiency and low emissions in a heavy duty (H D) diesel engine was investigated experimentally in a single cylinder test engine with a common rail fuel system, EGR (Exhaust Gas Recirculation) system, boost system and retarded intake valve closing timing actuator. For the operation loads of IMEPg (Gross Indicated Mean Effective Pressure) less than 1.1 MPa the low temperature combustion (LTC) with high rate of EGR was applied. The fuel injection modes of either single injection or multi-pulse injections, boost pressure and retarded intake valve closing timing (RIVCT) were also coupled with the engine operation condition loads for high efficiency and low emissions. A higher boost pressure played an important role in improving fuel efficiency and obtaining ultra-low soot and NOx emissions.

The Premixed Charge Compression Ignition (PCCI) engine has the potential to reduce soot and NOx emissions while maintaining high thermal efficiency at part load conditions. However, several technical barriers must be overcome. Notably ways must be found to control ignition timing, expand its limited operation range and limit the rate of heat release. In this paper, comparing with single fuel injection, the superiority of multiple-pulse fuel injection in extending engine load, improve emissions and thermal efficiency trade-off using high exhaust gas recirculation (EGR) and boost in diesel PCCI combustion is studied by engine experiments and simulation study. It was found that EGR can delay the start of hot temperature reactions, reduce the reaction speed to avoid knock combustion in high load, is a very useful method to expand high load limit of PCCI. EGR can reduce the NOx emission to a very small value in PCCI.

In this study, Partially Premixed Combustion (PPC) on a modified heavy-duty diesel engine was realized by hybrid combustion control strategy with flexible fuel injection timing, injection rate pattern modulation and high ratio of exhaust gas recirculation (EGR) at different engine loads. It features with different degrees of fuel/air mixture stratifications. The very low soot emissions of the experiments called for further understanding on soot formation mechanism so that to promote the capability of prediction. A new soot model was developed with highlight in effects of surface activity on soot growth for soot formation prediction in partially premixed combustion diesel engine. According to previous results from literatures on the importance of acetylene as growth specie of PAH and soot surface growth, a gas-phase reduced kinetic model of acetylene formation was developed and integrated into the new soot model.

A pressure accumulative injection rate controllable unit injector-PAIRCUI is proposed and developed. This unit injector is powered by fuel pressure accumulation controlled by an electronic control unit and its injection rate is shaped by inner valves of the injector. Inherent advantages of an accumulator type unit injector have been carried out in this new design, including sructural simplicity, totally flexible injection timing, medium common rail pressure, tolerable pump size and flow requirement. A number of decisive features have also been realized that are significant for high efficiency and low emissions of engine combustion, including higher mean effective injection pressure(MEIP), pilot injection capability and rapid end of injection. The injection pressure is independent of engine speed, but regulated upon engine load. These characteristics are beneficial in improving engine performance and fuel consumption.