Search Results

The influence of a large truck on the aerodynamics of a small passenger car in an overtaking manoeuvre on the motorway was considered, many years ago, during the 1970's, to be a potential problem for the vehicle aerodynamicist. The concern never became significant as vehicle architecture evolved and car weights increased. The current drive for improved fuel economy is advocating that a considerable reduction in vehicle mass is desirable and therefore it may be time to readdress the significance of the truck passing manoeuvre. A quasi-steady experiment has been undertaken at small model scale to examine the aerodynamic characteristics of a small car in proximity to a large truck. Measurements at yaw were included to crudely simulate the effects of a crosswind. The wind tunnel data is presented and the limitations of the experimental procedure are discussed.

In the wind tunnel the effect of a wind input on the aerodynamic characteristics of any road vehicle is simulated by yawing the vehicle. This represents a wind input where the wind velocity is constant with height above the ground. In reality the natural wind is a boundary layer flow and is sheared so that the wind velocity will vary with height. A CFD simulation has been conducted to compare the aerodynamic characteristics of a DrivAer model, in fastback and squareback form, subject to a crosswind flow, with and without shear. The yaw simulation has been carried out at a yaw angle of 10° and with one shear flow exponent. It is shown that the car experiences almost identical forces and moments in the two cases when the mass flow in the crosswind over the height of the car is similar. Load distributions are presented for the two cases. The implications for wind averaged drag are discussed.

Significant aerodynamic drag reduction is obtained on a bluff body by tapering the rear body. In the 1930’s it was found that a practical low drag car body could be achieved by cutting off the tail of a streamlined shape. The rear end of a car with a truncated tail is commonly referred to as a Kamm back. It has often been interpreted as implying that the drag of this type of body is almost the same as that for a fully streamlined shape. From a review of the limited research into truncated streamlined tails it is shown in this paper that, while true for some near axisymmetric bodies, it is not the case for many more car-like shapes. For these shapes the drag reduction from an elongated tail varies almost linearly with the reduction in cross section area. A CFD simulation to determine the drag reduction from a truncated streamlined tail of variable length on the simple Windsor Body is shown by way of confirmation.

There are many aspects of the unsteady flow around fastback passenger cars that remain to be understood. These include the source and nature of unsteady flow structures, the relevant time-scales, the effect of geometric parameters and the impact of the unsteadiness in terms of steady and unsteady forces on the vehicle. This paper investigates large scale unsteady structures in the wake of the Ahmed form and of a scale model of a real car shape using two wind tunnels and model scales between 12.5% and 40%. The unsteadiness demonstrated only low coherence and weak periodicity and the Strouhal number of a given structure varied from tunnel to tunnel indicating a high sensitivity to external influences. Nevertheless, a novel visualization technique, used to display the results of time-accurate pressure probe measurements, was able to reveal structures involving both symmetric and anti-symmetric oscillations in the strength of the rear-pillar vortices.

It has been recognised that the ideal flow conditions that exist in the modern automotive wind tunnel do not accurately simulate the environment experienced by vehicles on the road. This paper investigates the effect of varying one flow parameter, freestream turbulence, and a single shape parameter, leading edge radius, on aerodynamic drag. The tests were carried out at model scale in the Loughborough University Wind Tunnel, using a very simple 2-box shape, and in the MIRA Full Scale Wind Tunnel using the MIRA squareback Reference Car. Turbulence intensities up to 5% were generated by grids and had a strong effect on transcritical Reynolds number and Reynolds sensitivity at both model scale and full scale. There was a good correlation between the results in both tunnels.

The effects of adding a streamlined tail to a simple vehicle shape, represented by the Windsor Body has been investigated in a small scale wind tunnel experiment. The extended tail has a constant width, with a flat lower surface and a constant upper surface taper angle. The tail is truncated in steps to understand the trends in the principal aerodynamic characteristics. The slant surface and the base have been pressure tapped to indicate the contribution to drag and lift from these surfaces. The bodies have been tested over a range of yaw angles and wind tunnel airspeeds. The effects of adding wheels, albeit in a fixed ground experiment, has also been studied. The experimental data for the basic wheel-less body in a squareback configuration and with tapered tails of different length at zero yaw has been compared with an earlier CFD simulation of the same configurations.