Search Results

Turbocharging, increasing the compression ratio, and downsizing a spark-ignition engine are well known strategies for improving vehicle fuel economy. However, such strategies increase the likelihood of engine knock due to higher in-cylinder pressures and temperatures. A high octane fuel, such as E85, effectively suppresses knock but is not necessary in most parts of the engine operating map. To better utilize a high octane fuel, dual fuel injection has been suggested where high octane fuel is injected only when the engine is about to knock. However, the effects of downsizing, retarding spark timing, and increasing compression ratio on dual fuel applications are not well understood. To investigate these questions, GT-power simulations along with engine experiments and engine-in-vehicle simulations for a passenger vehicle and a medium-duty truck were conducted.

The increasing use of diesel and gasoline particulate filters requires advanced on-board diagnostics (OBD) to prevent and detect filter failures and malfunctions. Early detection of upstream (engine-out) malfunctions is paramount to preventing irreversible damage to downstream aftertreatment system components. Such early detection can mitigate the failure of the particulate filter resulting in the escape of emissions exceeding permissible limits and extend the component life. However, despite best efforts at early detection and filter failure prevention, the OBD system must also be able to detect filter failures when they occur. In this study, radio frequency (RF) sensors were used to directly monitor the particulate filter state of health for both gasoline particulate filter (GPF) and diesel particulate filter (DPF) applications.

High octane fuel (e.g., E85) effectively suppresses knock, but the octane ratings of such fuels are much above what is required under normal driving conditions. It is important, therefore, to understand the octane requirement of the engine itself over its full range of operation and apply that knowledge to practical driving cycles to understand fuel octane utilization, especially of a turbocharged engine. By carefully defining knock limits, the octane requirement of a 2-liter turbocharged spark ignition engine was experimentally quantified over a wide range of loads and speeds using PRF blends and gasoline-ethanol blends. Utilizing this knowledge and engine-in-vehicle simulations, the octane requirements of various driving cycles were calculated for a passenger car and a medium duty truck model.

Reliable means for on-board detection of particulate filter failures or malfunctions are needed to meet diagnostics (OBD) requirements. Detecting these failures, which result in tailpipe particulate matter (PM) emissions exceeding the OBD limit, over all operating conditions is challenging. Current approaches employ differential pressure sensors and downstream PM sensors, in combination with particulate filter and engine-out soot models. These conventional monitors typically operate over narrowly-defined time windows and do not provide a direct measure of the filter’s state of health. In contrast, radio frequency (RF) sensors, which transmit a wireless signal through the filter substrate provide a direct means for interrogating the condition of the filter itself.

The Cu-zeolite (CuZ) SCR catalyst enables higher NOx conversion efficiency in part because it can store a significant amount of NH3. “NH3 storage control”, where diesel exhaust fluid (DEF) is dosed in accord with a target NH3 loading, is widely used with CuZ catalysts to achieve very high efficiency. The NH3 loading actually achieved on the catalyst is currently estimated through a stoichiometric calculation. With future high-capacity CuZ catalyst designs, it is likely that the accuracy of this NH3 loading estimate will become limiting for NOx conversion efficiency. Therefore, a direct measurement of NH3 loading is needed; RF sensing enables this. Relative to RF sensing of soot in a DPF (which is in commercial production), RF sensing of NH3 adsorbed on CuZ is more challenging. Therefore, more attention must be paid to the “microwave resonance cavity” created within the SCR assembly. The objective of this study was to develop design guidelines to enable and enhance RF sensing.

Direct Injection (DI) fueled gasoline engines provide higher efficiency than port fueled injected (PFI) engines. However, emission of small particulates is greatly increased when DI is used. Particulate mass emission is increased by more than a factor of 10 and particulate number is increased by a factor of 10-100 relative to PFI engines leading to health concerns and to implementation and consideration of new regulations. Optimized combinations of PFI and DI can greatly reduce DI-generated particulate emissions without compromising efficiency and performance. A DI enhanced PFI mode of engine operation is employed where PFI is the dominant means in dual-injection fueling over a drive cycle, and the fuel fraction that is directly injected is reduced/minimized while still preventing knock at high loads. Further reduction can be obtained by optimal use of spark retard.

1 Downsizing and turbocharging a spark-ignited engine is becoming an important strategy in the engine industry for improving the efficiency of gasoline engines. Through boosting the air flow, the torque is increased, the engine can thus be downsized, engine friction is reduced in both absolute and relative terms, and engine efficiency is increased. However knock onset with a given octane rating fuel limits both compression ratio and boost levels. This paper explores the operating limits of a turbocharged engine, with various gasoline-ethanol blends, and the interaction between compression ratio, boost levels, and spark retard, to achieve significant increases in maximum engine mean effective pressure and efficiency.