Search Results

This paper presents a proof of concept for an algorithm to determine the attitude of a multi-layer laser rangefinder or LiDAR (Light Detection And Ranging) relative to a reference frame given the ability of the LiDAR to make measurements to a planar surface with sufficient and proper excitation. Due to the highly non-linear nature of the problem presented, weighted recursive least squares along with a high order unscented transform are used to obtain a final result which is capable of being extended to vehicle safety systems to provide a measurement of the roll and pitch of a vehicle relative to the road's surface with a high degree of accuracy.

A Computational Fluid Dynamics (CFD) study was completed to characterize the fuel consumption in terms of the separation distance of a Driver-Assistive-Truck-Platooning (DATP). The DATP system considered utilizes radar and GPS for a redundant range measurement, paired with Vehicle to Vehicle (V2V) communications to enable regulation of the longitudinal distance between the pair of trucks without acceleration input from the rear driver. The linkage of information between the trucks promotes increased safety between the following trucks, while improving their fuel economy. The results from this study are compared to previous works. Preliminary analysis of the system indicated that the fuel economy of both trucks increases dramatically as the separation distance diminishes. Additionally, an SAE Type-II fuel economy test complying with the (1986) SAE J1321 standard was completed to correlate the computational studies.

A Computational Fluid Dynamics (CFD) study was conducted on four-vehicle platoons, and the aerodynamic data is then coupled with a high-fidelity truck simulation software (TruckSim) to determine fuel efficiency. Previous studies typically have focused on identical two vehicle platoons, whereas this study accounted for more complex platoon configurations. Heavy duty vehicles (HDVs), both military and commercial, make up a significant percentage of fuel consumption. This study aimed to quantify fuel savings of a platoon consisting of dissimilar trucks and trailers, thus reducing vehicle operational cost. The vehicle platoon featured two M915 trucks and two Peterbilt 579 trucks with dissimilar trailer configurations. An unloaded flatbed trailer, a centered 20 ft shipping container, two 20 ft shipping containers, and a 53 ft box trailer configurations were utilized.

This paper investigates the use of GPS to estimate vehicle sideslip and tire information. Both a one antenna GPS antenna/receiver and dual GPS antenna method are studied. Analysis of the accuracy that can be achieved using the two different GPS solutions is provided. The algorithms are then validated on a fully instrumented Infiniti G35 sedan. Experimental data is given showing the performance of the GPS based sideslip estimates compared against a simple bicycle model and a Datron™ velocity sensor.

This paper investigates the effect of various vehicle parameters on rollover propensity using computer simulation. The computer simulation’s accuracy is verified by comparing it to experimental data from NHTSA’s Phase IV testing on rollover of passenger vehicles. The vehicle model used in the simulation study considers the non-linear, transient dynamics of both yaw and roll motion. The vehicle model is subjected to a specific steering input defined by NHTSA, the Fishhook 1a. A correlation between the vehicle parameter of center of gravity location and rollover propensity is found using the validated vehicle simulation.

This paper will describe the development of a load estimation algorithm that is used to estimate the load parameters necessary to detect a vehicle’s proximity to rollover. When operating a vehicle near its handling limits or with large loads, vehicle rollover must be considered for safe operation. Vehicle mass and center of gravity (CG) height play a large role in a vehicle’s rollover propensity. Cargo and passenger vehicles operate under a range of load configurations; therefore, changes in load should be estimated. Researchers have often developed load estimation and rollover detection algorithms separately. This paper will develop a load estimation algorithm and use the load estimates and vehicle states to detect rollover. The load estimation algorithm uses total least squares and is broken into two parts. First, mass is estimated based on a “full-car” dynamic ride model. Next, the CG height and inertia are estimated using the previously estimated mass and a dynamic roll model.

The fuel efficiency improvement of a prototype Driver-Assistive-Truck-Platooning (DATP) system was evaluated using Computational Fluid Dynamics (CFD). The DATP system uses a combination of radar and GPS, integrated active safety systems, and V2V communications to enable regulation of the longitudinal distance between pairs of trucks without acceleration input from the driver in the following truck(s). The V2V linking of active safety systems and synchronized braking promotes increased safety of close following trucks while improving their fuel economy. Vehicle configuration, speed, and separation distance are considered. The objectives of the CFD analysis are to optimize the target separation distance and to determine the overall drag reduction of the platoon. This reduction directly results in fuel economy gains for all cooperating vehicles.

Steering actuator lag is detrimental to the performance of lateral control systems and often leads to oscillation, reduced stability margins, and in some cases, instability. If the actuator lag is significant, compensation is required to maintain stability and meet performance specifications. Many recent works use a high-level approach to compensate for delay by utilizing model-based methods such as model predictive control (MPC). While these methods are effective when accurate models of both the vehicle and the actuator are available, they are susceptible to model errors. This work presents a low-level, adaptive control architecture to compensate for unknown or varying steering delay and dynamics. Using an inner-loop controller to regulate steer angle commands, oscillation can be reduced, and stability margins can be maintained without the need for an accurate vehicle model.