Search Results

E-fuels are proven to be a major contributing factor to reduce CO2 emissions in internal combustion engines. In gasoline engines, C1 oxygenate are seen as critical to reach CO2 and emission reduction goals. Their properties affect the fuel injection characteristics and thus the fuel mixture formation and combustion emissions. To exploit the full potential of e-fuels, the detailed knowledge of their spray characteristic is necessary. The correlation between the fuel content of C1 oxygenates and particulate emissions do not appear to be linear. To understand this correlation, the spray characteristics have to be investigated in detail. The reduced stoichiometric air requirement leads to an increase of the injected fuel mass, which has to evaporate. This can lead to a changed fuel film interaction within the combustion chamber walls and therefore a change of particle formation.

The subject of this paper is the reduction of the particle number emissions of a gasoline DI engine at high engine load (1.4 MPa IMEP). To reduce the particle number emissions, several parameters are investigated: the large scale charge motion (baseline configuration, tumble and swirl) can be varied at the single cylinder engine by using inlays in the intake port. The amount of residual gas can be influenced by the exhaust backpressure. By using a throttle valve, the exhaust backpressure can be set equal to the intake pressure and hence simulate a turbocharger's turbine in the exhaust system or the throttle valve can be wide open and thus simulate an engine using a supercharger. Additionally, higher fuel injection pressure can help to enhance mixture formation and thus decrease particulate formation. Therefore, a solenoid injector with a maximum pressure of 30 MPa is used in this work.

The investigation of transient engine operation plays a key role of the future challenges for individual mobility in terms of real driving emissions (RDE). A fundamental investigation of the transient engine operation requires the simultaneous application of measurement technologies for an integrated study of mixture formation, combustion process and emission formation. The major prerequisite is the combustion cycle and crank angle resolved analysis of the process for at least several individual consecutive combustion cycles during transient operation. The investigations are performed with a multi cylinder DISI engine at an Engine-in-the-Loop test bench, able to operate the engine in driving cycles as well as within target profiles (e.g. speed and torque profiles). The research project describes the methodology of analyzing elementary transient operational phases, (e.g. different variants of load steps).

The gradual global tightening of emission legislation for particulate matter emissions requires the development of new gasoline engine exhaust aftertreatment systems. For this reason, the development of gasoline direct injection engines aims at the reduction of particulate emissions by application of a Gasoline Particulate Filter (GPF). The regeneration temperature of GPF depend on soot reactivity towards oxidation and therefore on particle properties. In this study, the soot reactivity is correlated with nanostructural characteristics of primary gasoline particles as a function of specific engine injection parameters. The investigations on particle emissions were carried out on a turbocharged 4-cylinder GDI-engine that allows the variation of injection parameters. The emitted engine soot particles have been in-situ characterized towards their number and size distribution using an engine exhaust particle sizer (EEPS).

The spray propagation and disintegration is investigated in a pressure chamber. With Particle Image Velocimetry the direction and velocity of both, fuel droplets and induced gas flow are detected. By means of shadow photographs the spray cone geometry is visualized. To verify the predictions made of the measurements mentioned above and to rate the quality of the tuning of the parameters in-cylinder gas flow, injection pressure, position of Injector and position of spark plug under real engine conditions, a fast gas sampling valve is used in three different engines. The in-cylinder gas temperature and the soot concentration are measured crank angle resolved by means of the Two-Colour-Method in a 1-cylinder GDI-engine. The soot concentration and temperature show the influence of the injection pressure on emissions like soot and nitric oxide.

Modern gasoline direct injection engines with spray-guided combustion processes require a stable and reliable fuel mixture formation as well as an optimal stratification at time of ignition. Due to the limited time for this process the temporal and spatial analysis of the in-cylinder flow field and its influence is of significant interest. The application of a piezo injector with outward opening nozzle and its capability to realize multiple injections within the compression stroke provides additional degrees of freedom for the stratified engine operation. To improve the performance of this combination a detailed knowledge of the in-cylinder flow field and its interaction with the spray propagation during and after multiple injections is essential. The flow field measurements were applied in an optical borescope single-cylinder research engine using a high-speed particle image velocimetry (HSPIV) setup.

The particle size distribution (PSD) of submicron exhaust engine-out soot, is typically determined using a method based on the electrical mobility is used. This measurement procedure is subjected to uncertainty mainly due to inaccurate dilution of the sampled aerosol, unknown flow conditions at the probe inlet and the limited measurement accuracy of the device itself. In order to determine the measurement uncertainty, two different aerosol spectrometers, a TSI EEPS 3090 and a Cambustion DMS500 were installed and operated simultaneously at a single-cylinder heavy-duty diesel engine at the Institute of Internal Combustion Engines of the Karlsruhe Institute of Technology (KIT).The engine was operated at various operating points to evaluate the ability of the spectrometers to correctly determine the PSD and the total particle number concentration (TPNC) at different boundary conditions.