Search Results

There is a growing appreciation for using buses powered by alternative fuels in urban transport. Considered as such are city bus with engines fuelled with LNG and hybrid bus. This article, as shown above, provides a comparison of road exhaust emissions from three city buses: one with a CI engine fuelled with diesel fuel, and the other with a SI engine fuelled with LNG and Hybrid bus. Both vehicles (CI and LNG) conformed to Euro VI emission standard (hybrid bus EEV), and the tests were carried out in real traffic conditions. Equivocal opinions about differences in emissions from those types of buses, among others - CO2 and NOx emissions, were the underlying cause of the tests. The comparative study was carried out along the same urban routes during bus trips over the following days in similar traffic conditions. Exhaust road emission was determined based on the vehicle's curb weight and route length, and operating fuel consumption.

Non-plugin hybrids represent a technology with the capability to significantly reduce fuel consumption (FC), without any changes to refuelling infrastructure. The EU market share for this vehicle type in the passenger car segment was 3% in 2018 and this powertrain type remains of interest as an option to meet the European Union (EU) fleet average CO2 limits. EU legislative procedures require emissions limits to be met during the chassis dynamometer test and in the on-road real driving emissions (RDE) test, while official CO2/FC figures are quantified via the laboratory chassis dynamometer test only. This study employed both legislative test procedures and compared the results. Laboratory (chassis) dynamometer testing was conducted using the Worldwide Harmonised Light Vehicles Test Procedure (WLTP). On-road testing was carried out in accordance with RDE requirements, measuring the concentration of regulated gaseous emissions and the number of solid particles (PN).

In order to measure the concentration of toxic compounds a mobile analyzer for toxic tests SEMTECH DS by SENSORS Inc. was used. In the study the results of the vehicle emission tests in the road conditions were presented as this was the only way to obtain the information on real vehicle emissions. They include information on the emissivity of the vehicles in operation and deal with the real conditions of the vehicle motion. Reliable measurement results were obtained which were verified in simulated conditions on a chassis test bed. The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the harmful compound emissions. The dynamic engine properties were indirectly taken into account using all the speed range and the range of acceleration calculated for the city traffic in order to prepare a matrix of emission intensity.

In order to measure the concentration of exhaust emissions a mobile emission testing analyzer SEMTECH DS by SENSORS Inc was used. In the study the results of the vehicle emission tests in the road conditions were presented, as this was the only way to obtain the information on real vehicle emissions. They include information on the emissivity of the vehicles in operation and deal with the real conditions of the vehicle in motion. Reliable measurement results were obtained which were verified in simulated conditions on a chassis test bed. The obtained data were used to specify the dependence characteristics for the influence of the dynamic engine properties on the exhaust emissions. The dynamic engine properties were indirectly taken into account using all the speed range and the range of acceleration calculated for the city traffic in order to prepare a matrix of the emission intensity.

The paper presents the results of the investigations of an armored modular vehicle 8x8 Rosomak fitted with a diesel engine during start and warm-up. For the measurements of the toxic compounds a portable SEMTECH DS analyzer by SENSORS was used. The analyzer allowed a measurement of exhaust emission at the same time measuring the mass flow rate of the exhaust gases. The analysis of the PM emission was performed based on the measurement of the size of the particulate matter (analyzer 3090 EEPS - Engine Exhaust Particle Sizer™ Spectrometer - by TSI Incorporated) and counting of the particles (analyzer Particle Counter by AVL). The measurements of CO, HC, NOx, PM and fuel consumption have also been carried out under static conditions, during startup and at constant engine speed without engine load. For the measurement of the engine operating conditions and the fuel consumption a diagnostic vehicle system was used.

In this study, two vehicles were tested under real driving conditions with gaseous exhaust emissions measured using a portable emissions measurement system (PEMS). One of the vehicles featured a hybrid powertrain with a spark ignition internal combustion engine, while the other vehicle featured a non-hybrid (conventional) spark ignition internal combustion engine. Aside from differences in the powertrain, the two test vehicles were of very similar size, weight and aerodynamic profile, meaning that the power demand for a given driving trace was very similar for both vehicles. The test route covered urban conditions (but did include driving on a road with speed limit 90 km/h). The approximate test route distance was 12 km and the average speed was very close to 40 km/h.

The paper presents results of the road tests of exhaust gas emissions of vehicles of different emission classes (Euro 4 and Euro 5, with different mileage), fuelled with compressed natural gas. The tests of exhaust emissions were conducted on parts of the road with different characteristics of the traffic intensity. For each phase of the tests, the characteristics of the test run and the value of exhaust gas emissions were determined. To measure the exhaust emission the Portable Emission Measurement System (PEMS) was used.

This paper discusses the legislative situation regarding type approval of plug-in hybrid vehicles (also known as off-vehicle charging hybrid-electric vehicles, OVC-HEV) in the range of exhaust emissions and fuel consumption. A range of tests were conducted on two Euro 6d-complaint OVC-HEVs to quantify emissions. Procedures were based on EU legislative requirements. For laboratory (chassis dyno) testing, two different test cycles and three different ambient temperatures were used for testing. Furthermore, in some cases additional measurements were performed, including measurement of emissions of particulate matter and continuous analysis of regulated and unregulated pollutants in undiluted exhaust. Consumption of electrical energy was also monitored. On-road testing was conducted on the test vehicle tested on the chassis dyno in the tests mentioned above, as well as on a second OVC-HEV test vehicle.