Search Results

A dilution source sampling system has been incorporated into the exhaust measurement system of a research single-cylinder diesel engine. To allow more detailed assessment of the individual chemical components of the diesel particulate matter (PM) the exhaust dilution system includes a residence time chamber (RTC) to allow for residence times of 30 to 60 seconds in the second stage of dilution before sampling. Samples are collected on a range of different filters where mass loading, elemental and organic carbon (ECOC), trace metals, sulfate ions (SO4), particle-phase organic compounds, and semi-volatile organic compounds are evaluated. In addition, particle size distributions have been determined using a scanning mobility particle sizer (SMPS). Results show that the chemical composition of the particulate matter is highly dependent on the engine operating conditions.

The objective of the study is to characterize combustion and performance of a multi-cylinder turbocharged direct-injection (DI) diesel engine at altitude conditions according to the International Standard Atmosphere (ISA). Experiments were performed on the 6.6-liter turbocharged DI diesel engine, a model similar to that of the Army’s Joint Light Tactical Vehicle. The engine was installed in the US Army Research Laboratory Small Engine Altitude Research Facility. Outside air temperature (OAT) and outside air pressure were independently controlled to match the ISA-OAT at selected altitude conditions: sea level, 1524, 3048, and 4572 m. The test engine is equipped with a single-stage variable nozzle turbocharger and Bosch CRIN 3 common-rail injection system. Three load conditions (i.e., low, mid, and high) were selected at 1400 rpm to investigate combustion and performance of the engine using Jet Propellant-8 (JP-8) fuel.

The objective of the study was to investigate the spray and combustion characteristics of Jet Propellant-8 (JP-8) using a high-pressure fuel injector which is capable of up to 250-MPa fuel injection pressure. Experiments were performed in a constant-pressure flow-through combustion chamber at the ambient conditions of 825 K and 6 MPa for the oxygen concentration of 0 and 21%. JP-8 was injected over a range of fuel injection pressures from 50 to 250 MPa for single injection events to establish a baseline operation. Pilot and post injections were used to study the effect of multiple injections on spray and combustion of the high-pressure fuel injector. Both pilot and post injection separation times and quantities were systematically varied. JP-8 spray and combustion events were imaged at 75 kHz using a combination of Mie scattering and OH* chemiluminescence imaging.

Current regulations stipulate acceptable levels of particulate emissions based on the mass collected on filters obtained by sampling in diluted exhaust. Although precise, this gives us only aggregated information. If in addition to the mass based measurements, detailed chemical analysis of the particulate matter (PM) is performed, additional subtle information about the combustion process can be revealed. This paper reports the results of detailed chemical analysis of trace metal in the PM emitted from a single cylinder heavy-duty diesel engine. The trace metal concentrations are used as an indicator of oil consumption. Two techniques were used to make the trace metal concentration measurements. PM was captured on filters and trace metals were quantified with an Inductively Coupled Plasma Mass Spectrometer (ICPMS), and also an Aerosol Time-of-Flight Mass Spectrometer (ATOFMS) was used to perform particle size and composition measurements in real time.

Significant amounts of particle-phase organic compounds are present in the exhaust of diesel vehicles. It is believed that some of these compounds have a greater impact on human health and the environment than other compounds. Therefore, it is of significant importance to speciate particle-phase organic compounds of diesel particulate matter (PM) to clarify the effects of PM on human health and the environment, and to understand the mechanisms of organic compounds formation in PM. A dilution source sampling system was incorporated into the exhaust measurement system of a single-cylinder heavy-duty direct-injection (D.I.) diesel engine. This system was designed specifically to collect fine organic aerosols from diesel exhaust. The detailed system is described in Kweon et al. [27].

A study was performed in which the effects on the regulated emissions from a commercial small DI diesel engine were measured for different refinery-derived fuel blends. Seven different fuel blends were tested, of which two were deemed to merit more detailed evaluation. To investigate the effects of fuel properties on the combustion processes with these fuel blends, two-color pyrometry was used via optically accessible cylinderheads. Additional data were obtained with one of the fuel blends with a heavy-duty DI diesel engine. California diesel fuel was used as a baseline. The fuel blends were made by mixing the components typically found in gasoline, such as methyl tertiary-butyl ether (MTBE) and whole fluid catalytic cracking gasoline (WH-FCC). The mixing was performed on a volume basis. Cetane improver (CI) was added to maintain the same cetane number (CN) of the fuel blends as that of the baseline fuel.

Airborne compression-ignition engine operations differ significantly from those in ground vehicles, both in mission requirements and in operating conditions. Unique challenges exist in the aviation space, and electrification technologies originally developed for ground applications may be leveraged to address these considerations. One such technology, electrically assisted turbochargers (EATs), have the potential to address the following: increase the maximum system power output, directly control intake manifold air pressure, and reignite the engine at altitude conditions in the event of an engine flame-out. Sea-level experiments were carried out on a two-liter, four-cylinder compression-ignition engine with a commercial-off-the-shelf EAT that replaced the original turbocharger. The objective of these experiments was to demonstrate the technology, assess the performance, and evaluate control methods at sea level prior to altitude experimentation.