Search Results

The paper discusses the concept, specification and performance of a new, dedicated range extender engine for plug-in series hybrid vehicles conceived and designed by Lotus Engineering. This has been undertaken as part of a consortium project called Limo Green, part-funded by the UK government. The Lotus Range Extender engine has been conceived from the outset specifically as an engine for a plug-in series hybrid vehicle, therefore being free of some of the constraints placed on engines which have to mate to conventional, stepped mechanical transmissions. The paper starts by defining the philosophical difference between an engine for range extension and an engine for a full series hybrid vehicle, a distinction which is important with regard to how much power each type must produce. As part of this, the advantages of the sparkignition engine over the diesel are outlined.

The paper describes the design and development of ‘Sabre’, a 3-cylinder engine encompassing a combination of technologies to realise low CO2 in a practical automotive application while retaining driving pleasure (vehicle acceleration performance). This project is a partnership with Continental Automotive, in which Lotus Engineering is responsible for the base engine and combustion system. The decision process that led to a close-spaced direct injection combustion system that does not target high BMEP as the chief route to low fuel consumption is described. Instead of pursuing an approach in which specific power is maximized in order to reduce throttling losses at part load, mild downsizing coupled with throttling loss reduction and turbulence manipulation enabled by a switching valve train is employed.

The work reports results from tests employing different cooled EGR routes on a ‘Sabre’ direct-injection spark-ignition (DISI) research engine. As standard, this engine has been configured to provide good fuel consumption from a combination of mild downsizing, a combustion system with close-spaced injection and the adoption of a three-cylinder configuration in concert with an exhaust manifold integrated into the cylinder head. This has already been shown to offer a rated power specific fuel consumption of 272 g/kWh without cooled EGR. Three different EGR configurations are tested, with the best BSFC at nominal rated conditions being found to be 257-258 g/kWh at a cooled EGR rate of 6%. All of the EGR routing configurations tested in this work permit ready operation of the engine at Lambda 1 and MBT conditions, however, the results show little sensitivity in the combustion system to the actual routing employed.

Omnivore is a single cylinder spark ignition based research engine conceived to maximize the operating range of auto-ignition on a variety of fossil and renewable fuels. In order to maximize auto-ignition operation, the two-stroke cycle was adopted with two independent mechanisms for control. The charge trapping valve system is incorporated as a means of varying the quantity of trapped residuals whilst a variable compression ratio mechanism is included to give independent control over the end of compression temperature. The inclusion of these two technologies allows the benefits of trapped residual gas to be maximised (to minimize NOx formation) whilst permitting variation of the onset of auto-ignition. 2000rpm and idle are the main focus of concern whilst also observing the influence of injector location. This paper describes the rational behind the engine concept and presents the results achieved at the time of writing using 98ulg and E85 fuels.

Electrohydraulic and electromechanical valve train technologies for four-stroke engines are emerging which allow much greater flexibility and control of the valve events than can be achieved using mechanically-based systems. Much of the work done on exploiting the benefits of these systems has been directed towards improving engine fuel economy and reducing emissions. In the present work a study has been made, using an engine simulation program, in to some of the possible benefits to engine performance that may be facilitated by the flexibility of fully variable valve train (FVVT) systems. The simulation study indicates that FVVT systems, limited by realistic opening and closing rates, provide sufficient range in the valve event duration and timing to enable the engine to produce very high specific outputs whilst achieving a high level of torque in the low- and mid-speed range.

For efficiency, the majority of modern diesel engines implement multiple injection strategies, increasing the frequency of transient injection phases and thus, end of injection (EOI) events. Recent advances in diagnostic techniques have identified several EOI phenomena pertinent to nozzle surface wetting as a precursor for deposit formation and a potential contributor towards pollutant emissions. To investigate the underlying processes, highspeed optical measurements at the microscopic scale were performed inside a motored diesel engine under low load/idling conditions. Visualisation of the injector nozzle surface and near nozzle region permitted an indepth analysis of the post-injection phenomena and the behaviour of fuel films on the nozzle surface when the engine is not fired. Inspection of the high-speed video data enabled an interpretation of the fluid dynamics leading to surface wetting, elucidating the mechanisms of deposition and spreading.