Search Results

Concerns over energy security and global warming are beginning to be a serious issue for society and are also starting to drive customer purchasing decisions across many areas. Against this background there is an increasing call for motor sport to improve its environmental image, despite the fact that the global energy consumption and CO2 emissions attributable to motor sport are a very low proportion of the total. The real issue for motor sport in the face of the wider societal concerns is that, if it is truly at the cutting edge of relevant automotive engineering, it should be configured and managed in such a way as to drive technology for the betterment of mankind. The status quo is, it is contended, increasingly seen to be blatantly energy-profligate in the eyes of many people and this issue must be resolved if motor sport is to demonstrate the wider benefits of the technology developed by the huge financial investments committed to competing at the highest level.

Omnivore is a single cylinder spark ignition based research engine conceived to maximize the operating range of auto-ignition on a variety of fossil and renewable fuels. In order to maximize auto-ignition operation, the two-stroke cycle was adopted with two independent mechanisms for control. The charge trapping valve system is incorporated as a means of varying the quantity of trapped residuals whilst a variable compression ratio mechanism is included to give independent control over the end of compression temperature. The inclusion of these two technologies allows the benefits of trapped residual gas to be maximised (to minimize NOx formation) whilst permitting variation of the onset of auto-ignition. 2000rpm and idle are the main focus of concern whilst also observing the influence of injector location. This paper describes the rational behind the engine concept and presents the results achieved at the time of writing using 98ulg and E85 fuels.

The paper presents the concept of ternary blends of gasoline, ethanol and methanol in which the stoichiometric air-fuel ratio (AFR) is controlled to be 9.7:1, the same as that of conventional ‘E85’ alcohol-based fuel. This makes them iso-stoichiometric. Such blends are termed ‘GEM’ after the first initial of the three components. Calculated data is presented showing how the volumetric energy density relationship between the three components in these blends changes as the stoichiometric AFR is held constant but ethanol content is varied. From this data it is contended that such GEM blends can be ‘drop-in’ alternatives to E85, because when an engine is operated on any of these blends the pulse widths of the fuel injectors would not change significantly, and so there will be no impact on the on-board diagnostics from the use of such blends in existing E85/gasoline flex-fuel vehicles.

The use of methanol as spark-ignition engine fuel can help to increase energy security and offers the prospect of carbon neutral transport. Methanol's properties enable considerable improvements in engine performance, efficiency and CO2 emissions compared to gasoline operation. SAE paper 2012-01-1283 showed that both flex-fuel and dedicated methanol engines can benefit from an operating strategy employing exhaust gas recirculation (EGR) to control the load while leaving the throttle wide open (WOT). Compared to throttled stoichiometric operation, this reduces pumping work, cooling losses, dissociation and engine-out NOx. The current paper presents follow-up work to determine to what extent these advantages still stand over an entire drive cycle. The average vehicle efficiency, overall CO2 and NOx emissions from a flexible fuel vehicle completing a drive cycle on gasoline and methanol were evaluated.

One-dimensional ‘wave-action’ codes are widely used by internal combustion engine manufacturers. However, the modelling of multi-pipe junctions within such simulations presents a problem, since the geometry of the junctions cannot be represented fully using a one-dimensional approach, and it can produce a strongly directional effect on the propagated waves. ‘Pressure-loss’ models of junctions have been devised as boundary conditions for one-dimensional simulations, these allow the some geometry induced effects to be introduced into the calculation. This paper examines the performance of such models, when used to simulate a pulse converter-type junction, under unsteady flow conditions.

The propagation of pressure waves through junctions in engine manifolds is an intrinsically multi-dimensional phenomenon. In the present work an inviscid two-dimensional model has been applied to the simulation of shock-wave propagation through 45° and 90° junctions: the results are compared with schlieren images and measured pressure-time histories. The HLLC integral state Riemann solver is used in a shock-capturing finite volume scheme, with second-order accuracy achieved via slope limiters. The model can successfully predict the evolution of the wave fronts through the junctions and the high frequency pressure oscillations induced by the transverse reflections. The calculation time is such as to make it feasible for inclusion, as a local multi-dimensional region, within a one-dimensional wave-action engine simulation.

Computer programs to simulate the gas dynamics of internal combustion engines are commonly used by manufacturers to aid optimization. These programs are typically one-dimensional and complex flow features are included as ‘special’ boundaries. One such boundary is the ‘pressure-loss’ junction model, which allows the inclusion of directionality effects brought about by the geometry of a manifold junction. The pressure-loss junction model requires empirical, steady-flow pressure-loss data, which is both time consuming and expensive to obtain, and also requires the junction to be manufactured before its performance can be established. This paper presents a technique for estimating the steady-flow data, thus obviating the need to perform these flow-tests.