Search Results

Homogeneous lean spark-ignited combustion is known for its thermodynamic advantages over conventional stoichiometric combustion but remains a challenge due to combustion instability, engine knock and NOx emissions especially at higher engine loads above the naturally aspirated limit. Investigations have shown that lean combustion can partly suppress knock, which is why the concept may be particularly advantageous in high load, boosted operation in downsized engines with high compression ratios. However, the authors have previously shown that this is not true for all cases due to the appearance of a lean load limit, which is defined by the convergence of the knock limit and combustion stability limit. Therefore, further research has been conducted with the alternative and potentially renewable fuel methane which has higher resistance to autoignition compared to gasoline.

To characterize the effects of renewable fuels on particulate emissions from GDI engines, engine experiments were conducted using EN228-compliant gasoline fuel blends containing no oxygenates, 10% ethanol (EtOH), or 22% ethyl tert-butyl ether (ETBE). The experiments were conducted in a single cylinder GDI engine using a 6-hole fuel injector operated at 200 bar injection pressure. Both PN in raw exhaust and solid PN (SPN) were measured at two load points and various start of injection (SOI) timings. Raw PN and SPN results were classified into various size ranges, corresponding to current and future legislations. At early SOI timings, where particulate formation is dominated by diffusion flames on the piston due to liquid film, the oxygenated blends yielded dramatically higher PN and SPN emissions than reference gasoline because of fuel effects.

Gasoline and gasoline-ethanol sprays from an outward-opening piezo-injector were studied in a constant volume/pressure chamber using high-speed imaging and phase doppler anemometry (PDA) under stratified cold start conditions corresponding to a vehicle ambient temperature of 243 K (−30°C/−22°F); in-cylinder air pressure of 5 bar, air temperature of 350 K (−30°C/−22°F) and fuel temperature of 243 K. The effects of varying in-cylinder pressure and temperature, fuel injection pressure and fuel temperature on the formation of gasoline, E75 and pure ethanol sprays were investigated. The results indicate that fuel composition affects spray behaviour, but less than expected. Furthermore, varying the temperature of the fuel or the air surrounding the spray also had minor effects. As expected, the fuel injection pressure was found to have the strongest influence on spray formation under stratified conditions.

The spray formation and consequent atomization of an outward opening piezo-electric gasoline DI injector have been experimentally investigated in a constant pressure spray chamber. The sizes and velocities of the droplets and the resulting spray shape were evaluated, under different boundary conditions, using Planar Mie scattering and Planar Laser-induced Fluorescence (PLIF) in combination with Phase Doppler Anemometry (PDA) analyses and high-speed video photography. The use of piezo-electric actuation for gasoline DI injectors provides an additional means to control the atomization and spray shape that is not available with solenoid-driven injectors such as swirling and multi-hole type injectors. For instance, with piezo injectors up to four injections per cycle are possible, and the fuel flow rate can be controlled by adjusting needle lift. The captured high-speed video images show that a hollow-cone spray forms as the fuel exits the outward-opening nozzle.

Among many techniques used for increasing fuel efficiency of a modern Gasoline Direct-Injected (GDI) engine are boosting and stratified operation. In modern downsized GDI engines, boosting is standard in order to achieve a high power output. Boosted GDI-engines have however mostly been operated in homogenous mode and little is known on the effects of operating a boosted GDI-engine in stratified mode. This paper presents the influence on combustion, standard emissions and particulate size distribution in a Spray-Guided, Gasoline, Direct-Injected (SGDI), single cylinder, research engine operated with various levels of boost. The engine was operated in steady state mode at five engine operating points of various load and speed. The engine was boosted with a Roots blower and operated at four levels of boost as well as atmospheric pressure for comparison. The engine was fueled with market gasoline (95 RON) blended with 10% ethanol.

High-pressure multi-hole injectors are one candidate injector type for closed-spaced direct injection (DI) gasoline engines. In such a system, the spark plug must be located close to the spray and, during stratified operation, the spray is ignited very soon after the fuel droplets have been vaporized. Thus there are very high demands on the sprays used in such a system. An additional challenge is the positioning of the spark plug relative to the spray; both consistent ignitability and the absence of liquid fuel droplets must be achieved. Many injector parameters influence spray formation; for example, hole diameter, length to hole diameter ratio, nozzle hole configuration etc. This paper investigates the spray formation and spray induced air movement associated with rotational symmetrical and asymmetrical nozzle hole configurations.