Search Results

The paper describes the principal features of Omnivore, a spark-ignition-based research engine designed to investigate the possibility of true wide-range HCCI operation on a variety of fossil and renewable liquid fuels. The engine project is part-funded jointly by the United Kingdom's Department for the Environment, Food and Rural Affairs (DEFRA) and the Department of the Environment of Northern Ireland (DoENI). The engineering team includes Lotus Engineering, Jaguar Cars, Orbital Corporation and Queen's University Belfast. The research engine so far constructed is of a typical automotive cylinder capacity and operates on an externally-scavenged version of the two-port Day 2-stroke cycle, utilising both a variable charge trapping mechanism to control both trapped charge and residual concentration and a wide-range variable compression ratio (VCR) mechanism in the cylinder head.

A single-cylinder, 500cc research engine was tested under Spark-Ignition (SI) and Controlled Auto-Ignition (CAI) operation with similar load and speed conditions. Camshafts with low-lift and short duration, run with a negative valve overlap, were used to obtain CAI at wide open throttle. Two different camshaft profiles were tested in order to get a wide span of loads at 1200 and 2000rpm. The SI engine was Port Fuel-Injected (PFI) while the CAI engine was tested with both PFI and an Orbital Air-Assist Direct-Injection (DI) system. To reduce the high Indicated Specific Nitrogen Oxide (ISNOx) emissions at λ=1, 10% External Exhaust Gas Residuals (EEGR) was applied to the SI engine. EEGR reduced ISNOx emissions and there was slight reduction in ISFC. However, when the engine was tested in CAI mode, both ISNOx and ISFC were lower than the SI engine.

The unsteady gas dynamic phenomena in engine intake systems of the type found in racecars have been examined. In particular, the resonant tuning effects, including cylinder-to-cylinder power variations, which can occur as a result of the interaction between an engine and its airbox have been considered. Frequency analysis of the output from a Virtual 4-Stroke 1D engine simulation was used to characterise the forcing function applied by an engine to an airbox. A separate computational frequency sweeping technique, which employed the CFD package FLUENT, was used to determine the natural frequencies of virtual airboxes in isolation from an engine. Using this technique, an airbox with a natural frequency at 75 Hz was designed for a Yamaha R6 4-cylinder motorcycle engine. The existence of an airbox natural frequency at 75 Hz was subsequently confirmed by an experimental frequency sweeping technique carried out on the engine test bed.

The purpose of the ELEVATE (European Low Emission V4 Automotive Two-stroke Engine) industrial research project is to develop a small, compact, light weight, high torque and highly efficient clean gasoline 2-stroke engine of 120 kW which could industrially replace the relatively big existing automotive spark ignition or diesel 4-stroke engine used in the top of the mid size or in the large size vehicles, including the minivan vehicles used for multi people and family transportation. This new gasoline direct injection engine concept is based on the combined implementation on a 4-stroke bottom end of several 2-stroke engine innovative technologies such as the IAPAC compressed air assisted direct fuel injection, the CAI (Controlled Auto-Ignition) combustion process, the D2SC (Dual Delivery Screw SuperCharger) for both low pressure engine scavenging and higher pressure IAPAC air assisted DI and the ETV (Exhaust charge Trapping Valve).

This paper describes an experimental investigation into the effect of bore/stroke ratio on a simple two-stroke engine. This was achieved with a special purpose engine of modular design. The engine allowed four combinations of bore and stroke to be contrived to yield a common swept volume of 400 cm3 with bore/stroke ratios of: 0.8, 1.0, 1.2 and 1.4. Other factors that might affect engine performance were standardised: the exhaust, intake and ignition systems were common, the combustion chamber designs were similar, scavenge characteristics were similar, port timings and time-areas were kept the same, and cylinder and crankcase compression ratios were also kept the same. The most important conclusions were: Engine power was greatest with the compromise bore/stroke ratio of 1.0 or 1.2. Combustion efficiency tended to decrease with increasing bore/stroke ratio. Mechanical efficiency tended to increase with increasing bore/stroke ratio.