Search Results

The paper compares two different design concepts for a range extender engine rated at 30 kW at 4500 rpm. The first project is a conventional 4-Stroke SI engine, 2-cylinder, 2-valve, equipped with port fuel injection. The second is a new type of 2-Stroke loop scavenged SI engine, featuring a direct gasoline injection and a patented rotary valve for enhancing the induction and scavenging processes. Both power units have been virtually designed with the help of CFD simulation. Moreover, for the 2-Stroke engine, a prototype has been also built and tested at the dynamometer bench, allowing the authors to make a reliable theoretical comparison with the well assessed 4-Stroke unit.

In order to investigate the effects of split injection on emission formation and engine performance, experiments were carried out using a heavy duty single cylinder diesel engine. Split injections with varied dwell time and start of injection were investigated and compared with single injection cases. In order to isolate the effect of the selected parameters, other variables were kept constant. In this investigation no EGR was used. The engine was equipped with a common rail injection system with a piezo-electric injector. To interpret the observed phenomena, engine CFD simulations using the KIVA-3V code were also made. The results show that reductions in NOx emissions and brake specific fuel consumption were achieved for short dwell times whereas they both were increased when the dwell time was prolonged. No EGR was used so the soot levels were already very low in the cases of single injections.

Two-stroke diesel engines could be a promising solution for reducing carbon dioxide (CO2) emissions from light-duty vehicles. The main objective of this study was to assess the potential of two-stroke engines in achieving a substantial reduction in CO2 emissions compared to four-stroke diesel baselines. As part of this study 1-D models were developed for loop scavenged two-stroke and opposed piston two-stroke diesel engine concepts. Based on the engine models and an in-house vehicle model, projections were made for the CO2 emissions for a representative light-duty vehicle over the New European Driving Cycle and the Worldwide Harmonized Light Vehicles Test Procedure. The loop scavenged two-stroke engine had about 5-6% lower CO2 emissions over the two driving cycles compared to a state of the art four-stroke diesel engine, while the opposed piston diesel engine had about 13-15% potential benefit.

The internal combustion engine (ICE) for a series hybrid vehicle must be very compact, fuel efficient reliable and clean; furthermore it should possess excellent NVH features; finally, the cost should be as low as possible. An unconventional but not exotic solution, potentially ideal to fulfill all the above mentioned requirements, is represented by a 2-Stroke externally scavenged GDI engine, without poppet valves. BRC (Cherasco, Italy) and PRIMAVIS (Turin, Italy) are currently developing an engine of this type, incorporating a patented rotary valve for the control of the charge induced to cylinder. The development is supported by extensive CFD simulations, which are able to predict all the main engine performance characteristics. The paper analyzes, from a theoretical point of view, the installation of the engine on an electric vehicle, previously optimized for a small Diesel engine (Smart 0.8 l CDi).

The paper presents a numerical investigation, aimed to explore the potential of 2-stroke Diesel engines, able to meet Euro VI requirements, for application to medium size commercial vehicles (power rate: 80 kW at 2600 rpm, max. torque 420 Nm from 1200 to 1400 rpm). The study is based on experimental performance of a highly developed 4-stroke engine. Two different designs are considered: Loop and Uniflow scavenging, the latter obtained through an opposed piston configuration. In both cases, no poppet valves are used, and the lubrication is provided by a 4-stroke-like oil sump. The study started with the development of a 4-stroke EURO VI engine, on the basis of a previous EURO IV version. A prototype of the new engine (named 430) was built and tested.

Oxygen enriched air (EA) is a well known industrial mixture in which the content of oxygen is higher respect the atmospheric one, in the range 22-35%. Oxygen EA can be obtained by desorption from water, taking advantage of the higher oxygen solubility in water compared to the nitrogen one, since the Henry constants of this two gases are different. The production of EA by this new approach was already studied by experimental runs and theoretical considerations. New results using salt water are reported. EA promoted combustion is considered as one of the most interesting technologies to improve the performance in diesel engines and to simultaneously control and reduce pollution. This paper explores, by means of 3-dimensional computational fluid dynamics simulations, the effects of EA on the performance and exhaust emissions of a high-speed direct-injection diesel engine.

The basic requirements for range extender engines are low cost, compact dimensions, high specific power, good efficiency, low pollutant emission levels, excellent NVH behavior. For a power rate lower than 30 kW, it is very difficult to find an off-the-shelf engine meeting all the requirements listed above, so that a new generation of dedicated engines is under development. Following a preliminary theoretical work presented in 2012 [1], the current paper reviews the design process and the first experimental tests carried out on a novel 2-stroke GDI single-cylinder engine, rated at 30 kW at 4500 rpm, featuring a patented induction valve and a piston pump for scavenging. A prototype has been designed with the support of CFD simulations, then built and tested at the BRC laboratories, in Cherasco (Italy).

The new Stage 5 European regulation for Non Road Mobile Machinery has lowered the limits on pollutant emissions for all the categories of internal combustion engines. An interesting alternative to the implementation of sophisticated after-treatment systems is to downsize the engine, and provide the extra power for peak demands with an electric motor, installed in place of the flywheel. The paper explores the potential of this concept, applied to an industrial engine, manufactured by Kohler, and delivering a maximum power of 56 kW@2600 rpm. The study is supported by a comprehensive experimental characterization of the internal combustion engine and of the electric components. A representative duty cycle is also defined, on the basis of a set of measures, taken in real operating conditions. The analysis of this reference cycle is performed by using a GT-Suite model, comparing different power split strategies.

Biodiesel from Algae appears as an almost ideal solution to address the problem of decreasing availability of conventional fossil fuels, as well as to reduce the impact in terms of CO2 of internal combustion engines. In comparison to other biodiesels, algae do not compete for the land use with food cultures, and they have an excellent oil yield. Despite the significant amount of technical reports about the production process of algal biodiesel, detailed information about the application to current production engines is almost completely missing. The present paper describes the experimental campaign carried out on a current production 4-cylinder, 4-stroke naturally aspirated Diesel engine, running on standard Diesel oil and on a blend made up of 20% of oil manufactured by transesterification of Microalgae (B20). Performance and emission parameters have been measured over the whole engine operating range.

The paper describes a numerical study, supported by experiments, on light aircraft 2-Stroke Direct Injected Diesel engines, typically rated up to 110 kW (corresponding to about 150 imperial HP). The engines must be as light as possible and they are to be directly coupled to the propeller, without reduction drive. The ensuing main design constraints are: i) in-cylinder peak pressure as low as possible (typically, no more than 120 bar); ii) maximum rotational speed limited to 2600 rpm. As far as exhaust emissions are concerned, piston aircraft engines remain unregulated but lack of visible smoke is a customer requirement, so that a value of 1 is assumed as maximum Smoke number. For the reasons clarified in the paper, only three cylinder in line engines are investigated. Reference is made to two types of scavenging and combustion systems, designed by the authors with the assistance of state-of-the-art CFD tools and described in detail in a parallel paper.