Search Results

In this research, simulation and experimental investigation of H2 emission formation and its influence during the post-oxidation phenomenon were conducted on a turbo-charged spark ignition engine. During the post-oxidation phenomenon phase, rich air-fuel ratio (A/F) is used inside the cylinder. This rich excursion gives rise to the production of H2 emission by various reactions inside the cylinder. It is expected that the generation of this H2 emission can play a key role in the actuation of the post-oxidation and its reaction rate if enough temperature and mixing strength are attained. It is predicted that when rich combustion inside the cylinder will take place, more carbon monoxide (CO)/ Total Hydro Carbon (THC)/ Hydrogen (H2) contents will arrive in the exhaust manifold. This H2 content facilitates in the production of OH radical which contributes to the post-oxidation reaction and in-turn can aid towards increasing the enthalpy.

Turbocharged SI-DI-engines in combination with a reduction of engine displacement (“Downsizing”) offer the possibility to remarkably reduce the overall fuel consumption. In charged mode it is possible to scavenge fresh unburnt air into the exhaust system if a positive slope during the overlap phase of the gas exchange occurs. The matching of the turbo system in SI-engines always causes a trade-off between low-end torque and high power output. The higher mass flow at low engine speeds of an engine using scavenging allows a partial solution of this trade-off. Thus, higher downsizing grades and fuel consumption reduction potential can be obtained. Through scavenging the global fuel to air ratio deviates from the local in-cylinder fuel to air ratio. It is possible to use a rich in-cylinder fuel to air ratio, whereas the global fuel to air ratio remains stochiometrical. This could be very beneficial to reduce the effect of catalytic aging on the one hand and engine knock on the other hand.

Fulfilling exhaust emissions regulations and meet customer performance needs mainly drive the current engine development. Turbocharging system plays a key role for that. Currently turbocharging should provide highest engine power density at high engine speed by also allowing a very responsive performance at low end. This represents a trade-off in turbocharger development. A large scaled turbine allows having moderate exhaust gas back pressure for peak power region, but leading to loss of torque in low engine speed. In the last years of engine development scavenging helped to get away a bit from this trade-off as it increases the turbine mass flow and also reduces cylinder internal residual gas at low engine speed. The mostly in-use lean strategy runs air fuel ratios of closed to stoichiometric mixture in cylinder and global (pre catalyst) of λ = 1.05 to l = 1.3. This will be out of the narrow air fuel ratio band of λ = 1 to ensure NOx conversion in the 3-way-catalyst.

In order to operate effectively, exhaust gas aftertreatment (EAT) systems require a certain temperature level. The trend towards higher grades of hybridisation causes longer switch-off phases of the internal combustion engine (ICE) during which the EAT components cool down. Additionally, efficiency enhancements of the ICE result in lower exhaust gas temperatures. In combination with further strengthening of the legal requirements regarding tailpipe emissions, new approaches are desired to ensure reliable emission reductions under all conditions. One possibility to achieve a faster warm-up of the EAT system is to place it upstream of the turbine, where temperatures are higher. Although, the extra thermal inertia and larger volume upstream of the turbine delay the throttle response, even a light hybridisation is sufficient for compensating the dynamic loss.

The introduction of real driving emission measurements increases the need of improved transient engine behavior while keeping the emissions to a minimum. A possible way of enhancing the transient engine behavior is the targeted usage of scavenging. Scavenging is realized by an inlet- and exhaust-valve overlap. Fresh scavenging air flows directly from intake manifold through the cylinder into the exhaust manifold. Therefore, the mass flow at the turbine increases and causes a reduced turbo lag, which results in a more dynamic engine behavior. The unburned oxygen causes a decrease of the three-way catalyst (TWC) conversion rate. To keep the TWC operation close to stoichiometry, a rich combustion is performed. The rich combustion products (most notably carbon monoxide) mix in the exhaust manifold and react with oxygen so that the conversion rate of the TWC is ensured.