Search Results

Experiments were conducted in a turbocharged, high-pressure common rail diesel engine to investigate particulate emissions from the engine fueled with biodiesel and diesel blends. An electrical low-pressure impactor (ELPI) was employed to measure the particle size distribution and number concentration. Heated dilution was used to suppress nuclei mode particles and focus on accumulation mode particles. The experiment was carried out at five engine loads and two engine speeds. Biodiesel fractions of 10%, 20%, 40%, 60% and 80% in volume were tested. The study shows that most of the particles are distributed with their diameters between 0.02 and 0.2 μm, and the number concentration becomes quite small for the particles with the diameters larger than 0.2 μm. With the increase of biodiesel fraction, engine speed and/or engine load, particle number concentration decreases significantly, while the particle size distribution varies little.

Gasoline direct injection (GDI) engines have been developed rapidly in recent years, driven by stringent legislative requirements on vehicle fuel efficiency and emissions. However, one challenge facing GDI is the formation of particulate emissions, particularly with the presence of injector tip deposits. The Chinese market features some gasoline fuels that contain no detergent additives and are prone to deposit formation, which can affect engine performance and emissions. The use of detergent additives to mitigate the formation of injector deposits in a GDI engine was investigated in this study by testing a 1.5L turbocharged GDI engine available in the Chinese market. The engine was operated both on base gasoline and on gasoline dosed with detergent additives to evaluate the effect on injector deposit formation and engine performance and emissions.

Due to its load control strategy via fresh charge quantity, pumping loss in a homogenous charge gasoline engine is a significant contributor to the high fuel consumption rate at light load. Exhaust gas recirculation (EGR) and lean burn technologies are the common means to reduce gasoline engine pumping loss for fuel economy improvement. Many previous publications compared the EGR and lean burn concepts. However, few of those were able to compare the EGR and lean burn concepts under the same in-cylinder dilution basis. Usually the un-swept in-cylinder residual gas fraction (RGF), which can be significant at very low loads, was ignored due to lack of appropriate method to determine it. Also the theoretical potential and practical limitations were rarely discussed. In this paper, a Naturally Aspirated (NA) gasoline engine was systematically tested for both the EGR and lean mixture concepts on an engine dyno. under the same speed and load conditions.

Changan has upgraded its 1.6 L naturally aspirated GDI engine to meet future fuel economy and emission regulation base on its previous 1.6 L naturally aspirated GDI engine, the major upgrades include a high compression ratio of 13, 35Mpa direct injection system, cooled external EGR, thermo management module,and extensive measures to reduce friction. With this new engine, the vehicle fuel consumption is reduced by 9%, and meet the China 6b emission standard without GPF.

Performance and particulate emissions of a modern common-rail and turbocharged diesel engine fueled with diesel and biodiesel fuels were comparatively studied. An electrical low-pressure impactor (ELPI) was employed to measure particle size distribution and number concentration. Two biodiesel fuels, BDFs (biodiesel from soybean oil) and BDFc (biodiesel from used cooking oil), as well as ultra-low sulfur diesel were used. The study shows that biodiesels give higher thermal efficiency than diesel. Biodiesels give obviously lower exhaust gas temperature than diesel under high engine speed. The differences in fuel consumption, thermal efficiency and exhaust gas temperature between BDFs and BDFc are negligible. The first peaks of heat release rate for biodiesels are lower than that of diesel, while the second peaks are higher and advanced for biodiesels. BDFs show slightly slower heat release than BDFc during the first heat release stage at low engine speed.

Gasoline direct injection (GDI) engine technology is now widely used due to its high fuel efficiency and low CO2 emissions. However, particulate emissions pose one challenge to GDI technology, particularly in the presence of fuel injector deposits. In this paper, a 4-cylinder turbocharged GDI engine in the Chinese market was selected and operated at 2000rpm and 3bar BMEP condition for 55 hours to accumulate injector deposits. The engine spark timing, cylinder pressure, combustion duration, brake specific fuel consumption (BSFC), gaseous pollutants which include total hydro carbon (THC), NOx (NO and NO2) and carbon dioxide (CO), and particulate emissions were measured before and after the injector fouling test at eight different operating conditions. Test results indicated that mild injector fouling can result in an effect on engine combustion and emissions despite a small change in injector flow rate and pulse width.

Gasoline Direct Injection (GDI) engines have developed rapidly in recent years driven by fuel efficiency and consumption requirements, but face challenges such as injector deposits and particulate emissions compared to Port Fuel Injection (PFI) engines. While the mechanisms of GDI injector deposits formation and that of particulate emissions have been respectively revealed well, the impact of GDI injector deposits and their relation to particulate emissions have not yet been understood very well through systematic approach to investigate vehicle emissions together with injector spray analysis. In this paper, an experimental study was conducted on a GDI vehicle produced by a Chinese Original Equipment Manufacturer (OEM) and an optical spray test bench to determine the impact of injector deposits on spray and particulate emissions.