Search Results

Diesel engines provide the necessary power for accomplishing heavy tasks across the industries, but are known to produce high levels of noise. Additionally, each type of fuel possesses unique combustion characteristics that lead to different sound and vibration signatures. Noise is an indication of vibration, and components under excessive vibration may wear prematurely, leading to repair costs and downtime. New fuels that are sought to reduce emissions, and promote sustainability and energy independence must be investigated for compatibility from a sound and vibrations point-of-view also. In this research, the sound and vibration levels were analyzed for an omnivorous, single cylinder, CI research engine with alternative fuels and an advanced combustion strategy, RCCI. The fuels used were ULSD#2 as baseline, natural gas derived synthetic kerosene, and a low reactivity fuel n-Butanol for the PFI in the RCCI process.

This study investigates combustion and emissions of Jet-A in an indirect injection (IDI) compression ignition engine and a direct injection (DI) compression ignition engine at 4.5 bar IMEP and 2000 RPM. The Jet-A was blended with ULSD that resulted in 75%Jet-A and 25% ULSD#2 by mass. Both engines were instrumented with Kistler pressure sensors in the main chamber and the IDI engine had a second pressure sensor in the pre-chamber. Combustion properties and emissions from both engines using the 75% jet-A blend (75Jet-A) were compared to a baseline test of Ultra Low Sulfur Diesel #2 (ULSD). The ignition delay was shorter when running on 75Jet-A compared to ULSD in the DI engine. For ULSD, the ignition delay was 1.8 ms and it reduced to 1.7 ms when operating on 75Jet-A (difference of 6%). In the IDI engine the ignition delay for both fuels was 2.3 ms based off the gross heat release in the Pre-Chamber.

"The Single Fuel Forward Policy" legislation enacted in the United States mandates that deployed U.S. military ground vehicles must be operable with aviation fuel (JP-8). This substitution of JP-8 for diesel raises concerns about the compatibility of this fuel with existing reciprocating piston engine systems. This study investigates the combustion, emissions, and performance characteristics of blends of JP-8 and Ultra Low Sulfur Diesel (ULSD) fuels with similar cetane numbers (CN), 48 (JP-8) and 47(ULSD), respectively, in a direct injection (DI) compression ignition engine over the load range of 3-8 bar imep at 1400 rpm. The results showed that JP-8 blends and ULSD had ignition delays ranging from approximately 1.0-1.4 ms and an average combustion duration time in the range of 47-65 CAD. Cylinder maximum heat flux values were found to be between 2.0 and 4.4 MW/m₂, with radiation flux increasing much faster than convection flux while increasing the imep.

In this study, a direct injection (DI) compression ignition engine fueled with biodiesel was supplemented with n-butanol port fuel injection (PFI) in order to simultaneously reduce in cylinder nitrogen oxides formation, decrease soot and favorable modify their trade-off. The combustion and emission characteristics were investigated for regimes of 1-5 bars IMEP at 1400 rpm. By applying this methodology, for the regimes in which the n-butanol PFI was applied, the premixed charge combustion has been split into two regions of high temperature heat release, an early one, BTDC, and a second stage ATDC, oxidizing the soot formed from biodiesel combustion and therefore modifying favorable the soot-NOx trade-off. With n-butanol injection, the soot emissions showed a significant decrease as much as 90%, concomitantly with a 50% NOx reduction at higher PFI rates. Non-regulated emissions measurements showed increases in acetaldehyde with n-butanol PFI.

In this study, a Premixed Charge Compression Ignition (PCCI) obtained by sequential dual fueling strategy of n-butanol port fuel injection (PFI) and direct injection of ULSD#2 was investigated against binary mixtures combustion (defined as premixed in the tank) of n-butanol and ultra-low sulfur diesel (ULSD#2) with the same n-butanol to diesel ratios (35%, 50%, 65% by mass) in an omnivorous compression ignition engine. The hypothesis of the study is that combustion phasing (respectively CA50) can be successfully controlled by the above named strategies. Both fueling strategies controlled the high reactivity of the ULSD#2 and slowed down the chemical reactions with the low cetane number fuel, n-butanol. These processes led to fuel reactivity stratification and an increase in the ignition delay observed as the amount of n-butanol increased.

This study presents the combustion and emissions characteristics of Reactivity Controlled Combustion Ignition (RCCI) produced by early port fuel injection (PFI) of low reactivity n-butanol (normal butanol) coupled with in cylinder direct injection (DI) of cottonseed biodiesel in a diesel engine. The combustion and emissions characteristics were investigated at 5.5 bars IMEP at 1400 RPM. The baseline was taken from the combustion and emissions of ULSD #2 which had an ignition delay of 13° CAD or 1.5ms. The PFI of n-butanol and DI of cottonseed biodiesel strategy showed a shorter ignition delay of 12° CAD or 1.45ms, because of the higher CN of biodiesel. The combustion proceeded first by the ignition of the pilot (cottonseed biodiesel) BTDC that produced a premixed combustion phase, followed by the ignition of n-butanol that produced a second spike in heat release at 2° CAD ATDC.