Search Results

Mechanical friction and heat transfer in internal combustion engines are two highly researched topics, due to their importance on the mechanical and thermal efficiencies of the engine. Despite the research efforts that were done throughout the years on both these subjects, engine modeling is still somewhat limited by the use of sub-models which do not fully represent the phenomena happening in the engine. Developing new models require experimental data which is accurate, repeatable and which covers wide range of operation. In SAE 2018-01-0121, the conventional pressurized motored method was investigated and compared with other friction determination methods. The pressurized motored method proved to offer a good intermediate between the conventional motored tests, which offer good repeatability, and the fired tests which provide the real operating conditions, but lacks repeatability and accuracy.

Research on turbocharging for FSAE at the University of Malta, has been ongoing for a number of years. 1D simulations were done to determine best design configuration and determine a lowered compression ratio. A decompression plate was installed on the Kawasaki 600 cc engine. Calibration of the engine was performed on the engine dynamometer. A hot-gas test stand for testing of the turbocharger was developed. The turbocharger speed was measured by a custom built hall-effect sensing setup that is compact enough to be implemented also in the FSAE vehicle. Bespoke camshafts with optimized valve timing determined through WAVE 1D simulations and designed with Valdyn® were machined. The turbocharged setup was used on the University of Malta FSAE vehicle in the FSAE Italy 2017 competition. Knock was investigated through in-cylinder pressure measurements and use of commercial knock sensor on the 600 cc engine.

Several methods are nowadays used by OEM’s in order to determine engine friction through experiments to help them develop friction correlations to be used in 1D simulation models. Some of the friction measurement methods used are; Willans Line, Morse test, Teardown test and Indicated Method. Each of these methods have their own disadvantages, with some reliant on heavy assumptions. In this paper a friction measurement method is discussed which requires a conventional motoring dynamometer cell by which the engine can be motored at different speeds. The exhaust manifold of the motored 2 litre, 4 cylinder diesel engine was shorted to the intake manifold with an unrestrictive ‘shunt’ pipe which reroutes the exhausted air to the intake [1]. The shunt pipe was pressurized by an external source of compressed air to make up for blow-by losses. It is noted that the compressed air supply is thus a small fraction of what would be required if no recirculation is used.

The variation of in-cylinder heat transfer with parameters such as engine speed, air-to-fuel ratio, coolant temperature and compression ratio were frequently studied in classical research. These experimentally-obtained relationships are important for improving in-cylinder heat transfer models, essential in developing CO2 reducing strategies. In this publication, a 2.0 liter compression ignition engine was tested in the pressurized motored configuration. This developed experimental setup allowed testing of the engine at speeds ranging between 1400 rpm and 3000 rpm, with peak in-cylinder gas pressures from 40 bar to 100 bar. The engine was motored using different gas compositions chosen specifically to have ratios of specific heats of 1.40, 1.50, 1.60 and 1.67 at room temperature. This enabled motored testing with peak in-cylinder bulk gas temperatures ranging from 700 K to 1500 K.

In the ever increasing challenge of developing more efficient and less polluting engines, friction reduction is of significant importance and its investigation needs an accurate and reliable measurement technique. The Pressurized Motoring method is one of the techniques used for both friction and heat transfer measurements in internal combustion engines. This method is able to simulate mechanical loading on the engine components similar to the fired conditions. It also allows measurement of friction mean effective pressure (FMEP) with a much smaller uncertainty as opposed to that achieved from a typical firing setup. Despite its advantages, the FMEP measurements obtained by this method are usually criticized over the fact that the thermal conditions imposed in pressurized motoring are far detached from those seen in fired conditions. In light of these considerations, the authors have put forward a modification to the method, employing Argon in place of Air as pressurization medium.

Mechanical friction is a significant power dissipater in the internal combustion engine. In the effort of designing more efficient and less pollutant engines, friction reduction is certainly on the agenda to be investigated. Such investigation cannot be possible without an accurate measurement of the same quantity. This publication regards a continued study on the mechanical friction determination in an internal combustion engine using the Pressurised Motoring Method. In this work, the friction mean effective pressure of a four-cylinder compression ignition engine was investigated with varying engine speed and manifold pressurisation, using a dedicated high precision sensor for the correct determination of the cylinder Top Dead Centre position.

Mechanical friction and heat transfer in internal combustion engines have long been studied through both experimental and numerical simulation. This publication presents a continuation study on a Pressurized Motoring setup, which was presented in SAE paper 2018-01-0121 and found to offer robust measurements at relatively low investment and running cost. Apart from the limitation that the peak in-cylinder pressure occurs around 1 DegCA BTDC, the pressurized motoring method is often criticized on the fact that the gas temperatures in motoring are much lower than that in fired engines, hence might reflect in a different FMEP measurement. In the work presented in SAE paper 2019-01-0930, Argon was used as the pressurization gas due to its high ratio of specific heats. This allowed to achieve higher peak in-cylinder temperatures which close further the gap between fired and motored mechanical friction tests.

Hybrid powertrains utilize an engine to benefit from the power density of the liquid fuel to extend the range of the vehicle. On the other hand, the electric machine is used for; transient operation, for very low loads and where legislation prohibits any gaseous and particulate emissions. Consequently, the operating points of an engine nowadays shifted from its conventional, broad range of speed and load to a narrower operating range of high thermal efficiency. This requires a departure from conventional engine architecture, meaning that analytical models used to predict the behavior of the engines early in the design cycle are no longer always applicable. Friction models are an example of sub-models which struggle with previously unexplored engine architectures. The “pressurized motored” method has proven to be a simple experimental setup which allows a robust FMEP determination against which engine friction simulation can be fine-tuned.