Search Results

The exhaust emissions of two Euro 6 diesel cars with different emissions control systems have been evaluated both on the road and over various chassis dynamometer test cycles. European emissions limits are currently set using the New European Driving Cycle (NEDC), but the European Commission is preparing additional test procedures to ensure that emissions are well controlled both in real-world use and over the legislative test cycle. The main focus of this work on ‘Real Driving Emissions’ (RDE) is on measurements using Portable Emissions Measurement Systems (PEMS) in truly representative, on-road, driving. A key focus of the test programme, undertaken as a collaboration between AECC (the Association for Emissions Control by Catalyst) and Ricardo UK, was therefore the use of PEMS systems to measure on-road emissions of both gaseous pollutants and particulate matter. This included measurement of particle number emissions with a new candidate system for this type of measurement.

The European emission legislation for two-wheeler vehicles driven by engines of ≤ 50 cm₃ is continuously developing. One of the most important issues in the near future will be the finalization of the European Commission's proposals for future steps in the emissions regulations as well as the verification of the impacts of current standards on the market. To have a basis for the discussion about these topics, the Association for Emissions Control by Catalyst (AECC) with the Institute for Internal Combustion Engines and Thermodynamics of Graz University of Technology (IVT) carried out an extensive test program to show the actual emission situation of state-of-the-art mopeds including mass and number of particulate matter as well as unregulated gaseous components. One of the main goals of these tests was to measure exhaust emissions without any modifications to the engines of standard production vehicles available on the European market.

The market share of Gasoline Direct Injection (GDI) vehicles has been increasing, promoted by its positive contribution to the overall fleet fuel economy improvement. It has however been reported that this type of engine is emitting more ultrafine particles than the Euro 6c Particle Number (PN) limit of 6·1011 particles/km that will be introduced in Europe as of September 2017 in parallel with the Real Driving Emission (RDE) procedure. The emissions performance of a Euro 6b GDI passenger car was measured, first in the OEM build without a Gasoline Particulate Filter (GPF) and then as a demonstrator with a coated GPF in the underfloor position. Regulated emissions were measured on the European regulatory test cycles NEDC and WLTC and in real-world conditions with Portable Emissions Measurement Systems (PEMS) according to the published European RDE procedure (Commission Regulation (EU) 2016/427 and 2016/646).

AECC, the Association for Emissions Control by Catalyst, conducted a test program to compare the newly developed World-harmonized Light vehicles Test Cycle (WLTC) with the current European regulatory New European Drive Cycle (NEDC) and the cold-start Common Artemis Driving Cycle (CADC). Vehicle engines and aftertreatment technologies were selected to cover a wide range of future systems. Six European commercially available passenger cars were chosen: three Euro 5 Gasoline Direct Injection cars, two Euro 6 Diesel cars and a Euro 5 non-plug-in gasoline hybrid car. The hybrid car was tested with three different battery state of charge: nominal, minimum charge, and maximum charge. Investigations on the test temperature were also conducted by comparing emissions at 25°C and at −7°C. Regulated gaseous emissions (HC, CO, NOx) and particulate mass and particles number were measured, together with additional pollutants such as CH4, NO2 and ammonia.

The gap between diesel vehicle emissions in laboratory tests compared to those in use has been addressed by the introduction of the Real Driving Emissions (RDE) requirements. Modern diesel technology now demonstrates low emissions on the road over a wide range of driving conditions. This paper further demonstrates that consistent low nitrogen oxide (NOx) and particle number (PN) emissions can be achieved over a wide range of driving conditions beyond Euro 6d RDE requirements, with emission control technologies combined in an integrated approach. An LNT (Lean NOx Trap) is combined with a dual-dosing SCR (Selective Catalytic Reduction) system. Low-load NOx control is achieved by the LNT in combination with a close-coupled SCR coated on the Diesel Particulate Filter (SDPF). High load conditions, on the other hand, are covered by the underfloor SCR system with a second AdBlue® injector.

To get an overview of the emission situation in the field of small non-road mobile machinery powered by various types of SI engines, the Association for Emissions Control by Catalyst (AECC), together with the Institute for Internal Combustion Engines and Thermodynamics (IVT) of Graz University of Technology, conducted a customized test program. The main goal for this campaign was to derive information regarding the emissions of regulated gaseous components (following European Directive 97/68/EC) as well as particulate matter. With regard to the big variety of different engines that are available on the European and North-American market, the most representative ones had to be chosen. This resulted in a pool of test devices to cover different engine working principles (2-Stroke and 4-Stroke), technological standards (low-cost and professional tools) and different emissions control strategies (advanced combustion and exhaust gas aftertreatment).