Search Results

The effect of chromium oxide (Cr2O3) and partially stabilized zirconia (PSZ) surfaces on the gas-phase ignition of hydrocarbon fuels has been studied in a high pressure chemical flow reactor under low heat-loss Diesel engine simulated conditions. Results are presented for propane and n-hexane fuels at 6 and 10 atmospheres and are compared to previously reported results obtained under similar conditions with platinum surfaces. Thermal enhancement of the gas-phase reactions, as evidenced by the catalytic production of CO and CO2, was found to be negligible for both Cr2O3 and PSZ, where as significant thermal enhancement was observed with platinum. Chemical enhancement of the gas-phase ignition reactions, as evidenced by an increase in the production of intermediate hydrocarbons, was observed under fuel rich conditions with both Cr2O3 and PSZ. Oxygen was shown to be essential in that no change in the intermediate hydrocarbon concentration was observed under pyrolysis conditions.

Enhancement of methanol combustion in a direct injected Diesel engine using catalytically coated glow plugs was examined for platinum and palladium catalysts and compared to a non-catalytic baseline case. Experiments were performed for 6 and 10 brake Kilowatts (bKW) at 2500 rpm. Comparisons were made based on combustion, performance, and emissions including carbon monoxide (CO), oxides of nitrogen (NOx), unburned hydrocarbons (UHC), unburned methanol (UBM), and aldehydes. Results show a decrease in glow plug temperature of 100 K is achievable using platinum catalysts, and 150 K for palladium. Furthermore, the palladium catalyst was found to provide better combustion characteristics than the platinum catalyst. Also, the use of both catalysts produced lower aldehyde emissions, and the palladium reduced NOx emissions as well. However, unburned methanol increased for both catalytic glow plugs with respect to the non-catalytic case.

Results are presented from an experimental study of the effects of engine speed and injection pressure transients on the cold start performance of a gasoline direct injection engine operating on iso-octane. The experiments are performed in an optically-accessible single-cylinder research engine modified for gasoline direct injection operation. In order to isolate the effects of the engine speed and injection pressure transients, three different cold start simulations are used. In the first cold start simulation the engine speed and injection pressure are constant. In the second cold start simulation the injection pressure is constant while the engine speed transient of an actual cold start is simulated. In the third cold start simulation both the engine speed and the injection pressure transients of an actual cold start are simulated.

An experimental study has been conducted to characterize NO and soot evolution in an optically-accessible D.I. diesel engine with a square combustion chamber. Two-dimensional laser-induced fluorescence was used to characterize NO evolution. Soot evolution was characterized by two-dimensional laser-induced incandescence (LII) and Mie scattering techniques as well as direct photography of the flame luminosity. The engine operating parameters were set to provide optimum conditions for NO imaging. Attenuation of the UV beam proved to be the major obstacle in obtaining NO images. Therefore, oxygen was added to the intake air charge in order to reduce the optical density of the combustion medium. The NO images showed that the NO formation started almost immediately after ignition and ceased no later than 40 degrees ATDC. No soot images could be obtained by the laser-induced incandescence or Mie scattering methods before 20 degrees ATDC since the soot concentration was very low.

The application of planar laser-induced Rayleigh scattering for quantitative 2-D measurements of vapor-phase fuel concentration in the main combustion zone of a direct-injection Diesel engine has been explored, developed and demonstrated. All studies were conducted in an optically accessible direct-injection Diesel engine of the “heavy-duty” size class at 1200 rpm and motored TDC conditions which were typical of the production version of this engine. First, this study verifies that beyond 27 mm from the injector all the fuel is vapor phase. This was done by investigating the Diesel jet under high magnification using 2-D elastic scatter imaging and subsequently evaluating the signal intensities from the droplets and other interfering particles (Mie scattering) and the vapor (Rayleigh scattering).

The potential for catalytically enhanced ignition in low-heat rejection Diesel engines has been experimentally studied under engine simulated conditions in a high pressure chemical flow reactor. Results are presented for propane oxidation on platinum at 6 and 10 atmospheres, at temperatures from 800K to 1050K, and at equivalence ratios from 0.5 to 4.0. For turbulent transport rates which are typical of those in an engine, as much as 20% of the fuel was found to react on the catalyst before the onset of the gas-phase ignition reactions. Depending on the adiabaticity of the combustion chamber walls, this could lead to significant thermal enhancement of the gas-phase ignition process. Evidence of chemical enhancement was also observed, at 10 atm under very fuel rich conditions, in terms of a change in the concentration and distribution of the hydrocarbon intermediate species. Possible mechanisms for the observed chemical enhancement due to surface generated species are discussed.

The effects of intake-generated swirl and tumble on cold start performance have been investigated in a firing single-cylinder Gasoline Direct-Injection (GDI) engine. The engine utilizes a Ford Zetec cylinder head modified for GDI operation and a fused silica cylinder which provides extensive optical access to the combustion chamber. Uniquely designed port-inserts were positioned in the intake ports to generate enhanced swirling or tumbling motion inside the cylinder. Experiments were conducted using a constant speed (∼ 900 rpm) simulated cold start procedure, where the engine is motored for approximately 40 cycles, after which fuel injection and spark ignition commence and continue for 190 cycles and then the engine is stopped. Measurements were made of the various engine temperatures, engine-out total hydrocarbon emissions, and in-cylinder pressure throughout the test period.

Experiments have been conducted in a firing single-cylinder spark-ignition engine employing a Ford Zetec cylinder head that has been modified to operate with either standard port-fuel-injection, air-forced port-fuel-injection or direct-injection. The engine utilizes a fused silica cylinder and therefore provides extensive optical access to the combustion chamber. Tests were conducted using a constant speed simulated cold start procedure, which is composed of an initial start-up transient and a quasi-steady-state idle period. In this procedure, the engine is briefly motored at 889 rpm and then combustion commences shortly after the start of fuel injection. Measurements which were performed include in-cylinder pressure as well as intake valve, exhaust valve, piston, cylinder, head, and intake air temperature throughout each cycle of the test period. The engine-out total hydrocarbon emissions were also measured.