Search Results

An extensive literature search was conducted and potential additive candidates were identified to improve the safety aspects associated with the use of methanol as a motor fuel. Before any laboratory measurements were conducted, candidate additives were evaluated for possible formation of known or suspected toxic compounds as combustion products. The remaining potential additives were then screened for their effectiveness in improving methanol fuel properties in a laboratory test program emphasizing flame luminosity, lubricity, and flammability. Flame luminosity was measured with a specially designed system to monitor the light produced by the flame in lux. Lubricity was measured with a Ball-on-Cylinder Lubricity Evaluator (BOCLE). For flammability limits, a device was designed to determine the presence of flammable vapors above the liquid at different additive concentrations.

This paper summarizes the impact of recent developments in diesel fuel and the effect of these changes in conjunction with emerging compression-ignition engine technologies. Some changes were made to reduce exhaust emissions or were the result of advancements in aftertreatment systems. These changes included fuel properties such as aromatic and sulfur content, cetane number, density, lubricity, and viscosity. Other changes included the introduction of blending components and additives. Blending components included such things as water, ethanol, and bio-mass materials. The pros and cons related to these changes in diesel fuel technologies are discussed.

The Tank-Automotive RD&E Center periodically conducts foreign materiel evaluations to assess the current state of the art for ground vehicle technologies. The Propulsion Laboratory is conducting performance evaluations of an opposed-piston two-stroke diesel tank engine produced by the Kharkov Design Bureau in Ukraine. A key factor in the performance of all two-stroke engines is the scavenging process, which determines how well the cylinders are emptied of exhaust and filled with fresh air. The overall air flow rate is not sufficient to determine this, as a significant amount of air may be lost through the exhaust ports during the scavenging process. The inlet tracer gas method was employed to provide the additional data required. With methane as the tracer, it produced reasonable and consistent data over a wide range of engine speeds and loads. The inlet tracer gas method was found to be an effective tool for measuring the scavenging performance of a running two-stroke diesel engine.

Two additive blends proposed for improving the flame luminosity in neat methanol fuel were investigated to determine the effect of these additives on the exhaust emissions in a dual-fueled Volkswagen Jetta. The two blends contained 4 percent toluene plus 2 percent indan in methanol and 5 percent cyclopentene plus 5 percent indan in methanol. Each blend was tested for regulated and unregulated emissions as well as a speciation of the exhaust hydrocarbons resulting from use of each fuel. The vehicle exhaust emissions from these two fuel blends were compared to the Coordinating Research Council Auto-Oil national average gasoline (RF-A), M100, and M85 blended from RF-A. Carter Maximum Incremental Reactivity Factors were applied to the speciated hydrocarbon emission results to determine the potential ozone formation for each fuel. Toxic emissions as defined in the 1990 Clean Air Act were also compared for each fuel.

This paper reviews the use of additives to improve safety aspects associated with the use of methanol as a motor fuel. A survey of the literature was conducted to determine candidate additives for methanol that produce one or more of the following properties: provide a visible or luminous flame, reduce the potential for skin contact, give a foul or unpleasant taste and odor, and act as an emetic. Candidate additives were reviewed to determine potential effectiveness, cost, east of production, health problems, and effects on vehicle performance. Potential additives include complex hydrocarbon mixtures such as gasoline, alcohol soluble dyes and unpalatable compounds such as denatonium benzoate.

Neat methanol fuel (M100) has many advantages for achieving low emission levels as an automotive fuel, but there are several items that require attention before this fuel can replace conventional fuels. One item involves the low flame luminosity of methanol. An extensive literature search and laboratory evaluation were conducted to identify potential additive candidates to improve the luminosity of a methanol flame. Potential compounds were screened based on their concentration, luminosity improvement, and duration of luminosity improvement during the burn. Three compounds were found to increase the flame luminosity for segments of the burn at relatively low concentrations: toluene, cyclopentene, and indan. In combination, these three compounds markedly improved the luminosity of methanol throughout the majority of the burn. The two combinations were 1) 4 percent toluene plus 2 percent indan and 2) 5 percent cyclopentene plus 5 percent indan in methanol.