Search Results

The development of a modern internal combustion engine can be characterized by three main trends: durability increase, emission reduction, and fuel economy improvement. Ring pack design addresses all of these issues. The ring behavior affects the blow-by past the ring pack, the oil film left on the cylinder liner, the friction force between the liner and the ring, and the wear of the ring and the cylinder liner. In order to predict these phenomena, the prediction of inter-ring gas flow and ring behavior, especially ring motion and ring twist about ring centroid, is needed. This paper presents the results of the modeling of 3-dimensional ring twist and its influence on ring performance and blow-by. The TWIST program includes a 3-dimensional beam model of a piston ring.

Three-dimensional transient simulations using KIVA-3V were conducted on a 4-stroke high-compression ratio, methanol-fueled, direct-injection (DI) engine. The engine had two intake ports that were designed to impart a swirling motion to the intake air. In some cases, the intake system was modified, by decreasing the ports diameter in order to increase the swirl ratio. To investigate the effect of adding shrouds to the intake valves on swirl, two sets of intake valves were considered; the first set consisted of conventional valves, and the second set of valves had back shrouds to restrict airflow from the backside of the valves. In addition, the effect of using one or two intake ports on swirl generation was determined by blocking one of the ports.

Numerical simulations of lean Methanol combustion in a four-stroke internal combustion engine were conducted on a high-compression ratio engine. The engine had a removable integral injector ignition source insert that allowed changing the head dome volume, and the location of the spark plug relative to the fuel injector. It had two intake valves and two exhaust ports. The intake ports were designed so the airflow into the engine exhibited no tumble or swirl motions in the cylinder. Three different engine configurations were considered: One configuration had a flat head and piston, and the other two had a hemispherical combustion chamber in the cylinder head and a hemispherical bowl in the piston, with different volumes. The relative equivalence ratio (Lambda), injection timing and ignition timing were varied to determine the operating range for each configuration. Lambda (λ) values from 1.5 to 2.75 were considered.

The paper presents reportage of the debate on the topic expressed by its title that was held as a special session at the SAE 2003 Congress, supplemented by commentaries on its highlights. The debate brought to focus the fact that fuel cells are, indeed, superb powerplants for automobiles, while hydrogen is at the pinnacle of superiority as the most refined fuel. The problems that remained unresolved, are: (1) when fuel cells will be practically viable to replace internal combustion engines and (2) under what circumstances hydrogen, as the ultimate fuel, will be economically viable in view of its intrinsically high cost and hazards engendered by its extraordinary flammability and explosive tendency.

A stratified charge research engine and test stand were designed and built for this work. The engine was designed to exhibit some of the desirable traits of both the premixed charge gasoline engine and modern diesel engine. This spark ignition engine is fueled by M100 (99.99% pure methanol), operates under high compression (19.3:1) and uses direct fuel injection to form a stratification of the fuel-air mixture in the cylinder. The beginning of the combustion event of the stratified mixture is triggered by spark plug discharge. The primary goal of this project was to evaluate the feasibility of using a removable integral injector ignition source insert, which allows a convenient method of changing the relative location of the fuel injector to the ignition source, as well as the compression ratio, squish height, and bowl volumes. This paper provides an explanation of the hardware included in the experimental setup of the engine and selection of the direct injector configuration.

A numerical study on the combustion of Methanol in a directly injected (DI) engine was conducted. The study considers the effect of the bowl-in-piston (BIP) geometry, swirl ratio (SR), and relative equivalence ratio (λ), on flame propagation and burn rate of Methanol in a 4-stroke engine. Ignition-assist in this engine was accomplished by a spark plug system. Numerical simulations of two different BIP geometries were considered. Combustion characteristics of Methanol under swirl and no-swirl conditions were investigated. In addition, the amount of injected fuel was varied in order to determine the effect of stoichiometry on combustion. Only the compression and expansion strokes were simulated. The results show that fuel-air mixing, combustion, and flame propagation was significantly enhanced when swirl was turned on. This resulted in a higher peak pressure in the cylinder, and more heat loss through the cylinder walls.

This paper reports the development of vapor/liquid visualization systems based on an exciplex (excited state complex) formed between dimethyl- or diethyl-substituted aniline and trimethyl-substituted naphthalenes. Quantum yields of individual monomers were measured and the exciplex emission spectra as well as fluorescence quenching mechanisms were analyzed. Among the many systems and formulations investigated in this study, an exciplex consisting of 7% 1,4,6-trimethylnaphthalene (TMN) and 5% N,N-dimethylaniline (DMA) in 88% isooctane was found to be the best system for the laser-induced exciplex fluorescence (LIEF) technique, which is used to observe mixture formation in diesel or spark ignition (SI) engines. Observation of spectrally separated fluorescence from monomer in the gas phase and from exciplex in the gasoline fuel [1] requires that the exciplex forming dopants have boiling points within the distillation range of gasoline (20 to 215°C).

Significant improvement of engine performance can be achieved by ushering in a micro-electronic system to control the execution of combustion - an exothermic process whose sole purpose is to generate pressure. Hence, the primary feedback for the controller is provided by a pressure transducer. The activators are piezo-electrically activated pintle valves of MEMS type. The task of the micro-electronic processor is to provide an accurate feed-forward signal for the actuators on the basis of the information obtained from the feedback signal, within a time interval between consecutive cycles. Furnished here for this purpose is an algorithm for an interface module between the pressure sensor and the governor. Concomitantly, the gains thus attainable in the reduction of fuel consumption and curtailment of pollutant formation are thereby assessed. The implementation of this method of approach is illustrated by application to a HCCI engine.

Increasing oil prices and more stringent emission laws require an improved efficiency from future automotive engines. Additionally, the competition of the automotive market demands longer service intervals and engine life-times. A potential to decrease the specific fuel consumption and improve specific volume is offered by means of increasing engine speed and maximum cylinder pressure. Hence, the mechanical stress on the tribological system including the piston, piston rings, cylinder liner, are increased and the reliability decreases. The objective of this research is the development of a mathematical model implemented in software, which can deliver a prediction of piston ring wear in internal combustion engines. The program has been applied to a top compression piston ring of a turbo charged Diesel engine at WOT operation conditions.

The ring-pack behavior in a modern gasoline engine represent complicated phenomena. The process of ring pack design consists of two stages: understanding the physical behavior and design synthesis on the systematic manner. Computer models give an inside on the physical processes associated with the ring-pack behavior. Mathematical optimization techniques provide the tools for design synthesis on the systematic way based on an optimal criteria. The mathematical optimization technique was developed and applied to ring pack design synthesis. When applied to the existing engine ring-pack designs, the optimized results indicated the potential for significant reduction in blow-by through the ring-pack by optimizing ring pack geometry. The optimization results were compared with the original ring pack designs for two gasoline engines for a wide range of operating conditions.