Search Results

Diesel spray experimentation at controlled high-temperature and high-pressure conditions is intended to provide a more fundamental understanding of diesel combustion than can be achieved in engine experiments. This level of understanding is needed to develop the high-fidelity multi-scale CFD models that will be used to optimize future engine designs. Several spray chamber facilities capable of high-temperature, high-pressure conditions typical of engine combustion have been developed, but because of the uniqueness of each facility, there are uncertainties about their operation. For this paper, we describe results from comparative studies using constant-volume vessels at Sandia National Laboratories and IFP.

An experimental study has been carried out on the homogeneous charge compression ignition (HCCI) combustion of Dimethyl Ether (DME). The study was performed as a parameter variation of engine speed and compression ratio on excess air ratios of approximately 2.5, 3 and 4. The compression ratio was adjusted in steps to find suitable regions of operation, and the effect of engine speed was studied at 1000, 2000 and 3000 RPM. It was found that leaner excess air ratios require higher compression ratios to achieve satisfactory combustion. Engine speed also affects operation significantly.

Seven shapes of piston crowns have been evaluated for their ability to reduce HCCI knock and transmission of combustion noise to the engine. The performance of each piston crown was evaluated with measurements of cylinder pressure, engine vibration and acoustic sound pressure measured one meter away from the engine. The experiments were conducted in a diesel engine that was run in HCCI combustion mode with a fixed quantity of DME as fuel. The results show that combustion knock is effectively suppressed by limiting the size of the volume in which the combustion occurs. Splitting the compression volume into four smaller volumes placed between the perimeter of the piston and the cylinder liner increased the noise to a higher level than that generated with a flat piston crown. This was due to resonance between the four volumes. Using eight volumes instead decreased the noise.

Investigations were made concerning the formation of combustion chamber deposits (CCD) in SI gas engines fueled by producer gas. The main objective was to determine and characterise CCD and PAH formation caused by the presence of the light tar compounds phenol and guaiacol in producer gas from an updraft gasifier. The work was based on previous work regarding the assumption that phenol is a soot precursor and therefore could lead to CCD formation. Laboratory experiments were conducted, where pyrolysis products of the single tar components were collected on small aluminium plates. The experiments showed that guaiacol formed significant amount of deposits. The structure observed was a lacquer type of deposit. It was determined that there was no distinct deposit formation due to phenol. Experiments were conducted with a 0.48 litre one-cylinder high compression ratio SI engine fueled by synthetic producer gas.

The paper describes the optimization of a 50 cc crankcase scavenged two-stroke diesel engine operating on dimethyl ether (DME). The optimization is primarily done with respect to engine efficiency. The underlying idea behind the work is that the low weight, low internal friction and low engine-out NOx of such an engine could make it ideal for future vehicles operating on second-generation biofuels. Data is presented for the performance and emissions at the current state of development of the engine. Brake efficiencies above 30% were obtained despite the small size of the engine. In addition, efficiencies near the maximum were found over a wide operating range of speeds and loads. Maximum bmep is 500 kPa. Results are shown for engine speeds ranging from 2000 to 5000 rpm and loads from idle to full load. At all speeds and loads NOx emissions are below 200 ppm and smokeless operation is achieved. Design improvements relative to an earlier prototype are described.

Development of numerical tools for quantitatively assessing biofuel combustion in Internal Combustion Engines and facilitating the identification of optimum operating parameters and emission strategy are challenges of engine combustion research. Biofuels obtained through e.g. a Fischer-Tropsch process (FT) are complex mixtures of wide ranges of high molecular weight hydrocarbons in the diesel and naphtha boiling range dominated by C10-C18 hydrocarbons in n-alkane, iso-alkane, alkenes, aromatic and oxygenate classes. In this paper modeling of combustion in a rapid compression machine has been performed using model compounds from a given FT biofuel distribution as surrogate fuels. Furthermore, the detailed mechanism has been reduced by applying an automatic necessity analysis removing redundant species from the detailed model.

Engine experiments were carried out on a six cylinder DI-diesel engine using synthetic fuel and lubricant containing no PAH (Polycyclic Aromatic Hydrocarbons) [1]. By selectively doping the fuel and oil with pyrene, the effect of fuel and oil originating PAH on the exhaust emissions could be investigated. The experimental results are analyzed in a new way by suggesting a general transport model for PAH. By estimating as many transport quantities as possible it is attempted to gain knowledge about the most dominant mechanisms. The main finding is not surprisingly that for commercial fuels containing substantial concentrations of PAH, the by far major contributor to exhaust PAH is unburned fuel PAH. The concentration of PAH in the oil sump affects only weakly the PAH concentration in the exhaust for engines operating on commercial fuels. The PAH desorbing from the liner are getting burned efficiently, thereby being insignificant.

The effects of lubricant composition on hydrocarbon emissions from a SI engine have been experimentally investigated. Results based on measurements of solubilities of different fuel components in different types of lubricants are presented. 2 lubricants and two hydrocarbons were chosen for testing in a single cylinder engine. Emissions and performance was measured for various fuel air ratios and ignition timings. The lubricant with the lowest solubility with respect to isooctane also showed the lowest hydrocarbon emissions. The influence of the lubricant was greatest at lean air fuel ratios. Xylene is much more soluble in the lubricants than isooctane and gave lower hydrocarbon emissions when the engine was operated at rich air fuel ratios. At leaner mixtures, isooctane gave lower emissions. The results indicate that the lubricant plays a contributing, but not dominating role in hydrocarbon emissions from gasoline engines.

The effects of methanol and EGR on HCCI combustion of dimethyl ether have been tested separately in a diesel engine. The engine was equipped with a common rail injection system which allowed for random injection of DME. The engine could therefore be operated either as a normal DI CI engine or, by advancing the injection timing 360 CAD, as an HCCI engine. The compression ratio of the engine was reduced to 14.5 by enlarging the piston bowls. The engine was operated in HCCI mode with DME at an equivalence ratio of 0.25. To retard the combustion timing, methanol was port fuel injected and the optimum quantity required was determined. The added methanol increased the BMEP by increasing the total heat release and retarding the combustion to after TDC. Engine knock was reduced with increasing quantities of methanol. The highest BMEP was achieved when the equivalence ratio of methanol was around 0.12 at 1000 RPM, and around 0.76 at 1800 RPM. EGR was also used to retarding the timing.

This work concerns the modelling of soot formation process in diesel spray combustion under engine-like conditions. The key aim is to investigate the soot formation characteristics at different ambient temperatures. Prior to simulating the diesel combustion, numerical models including a revised multi-step soot model is validated by comparing to the experimental data of n-dodecane fuel in which the associated chemistry is better understood. In the diesel spray simulations, a single component n-heptane mechanism and the multi-component Diesel Oil Surrogate (DOS) model are adopted. A newly developed C16-based model which comprises skeletal mechanisms of n-hexadecane, heptamethylnonane, cyclohexane and toluene is also implemented. Comparisons of the results show that the simulated liftoff lengths are reasonably well-matched to the experimental measurement, where the relative differences are retained to below 18%.

This study explores the feasibility of using a sustainable lignin-based fuel, consisting of 44 % lignin, 50 % ethanol, and 6 % water, in conventional compression ignition (CI) marine engines. Through experimental evaluations on a modified small-bore CI engine, we identified the primary challenges associated with lignin-based fuel, including engine startup and shutdown issues due to solvent evaporation and lignin solidification inside the fuel system, and deposit formation on cylinder walls leading to piston ring seizure. To address these issues, we developed a fuel switching system transitioning from lignin-based fuel to cleaning fuel with 85 vol% of acetone, 10 vol% of water and 5 vol% of ignition improving additive, effectively preventing system clogs.