Search Results

Soot emissions in the combustion process of diesel engines are greatly harmful to the environment and human health. Consequently, there is large interest and great efforts in decreasing soot emission from diesel engines to meet the increasingly stringent emission standards. The mechanisms of soot formation and oxidation so far have not been well understood. Laser induced incandescence (LII) is particularly suited to measure the instantaneous spatial distribution of the soot volume concentration, which can offer much needed detailed information of soot distribution for better understanding of soot formation and oxidation. In this paper, a two-color laser induced incandescence (2C-LII) technique was implemented for measuring absolute soot volume fraction in a laminar diesel fuel diffusion flame.

Biodiesel is an alternative, renewable, clean fuel, which can effectively reduce emissions from diesel engines. However, the effects of biodiesel on engine emissions vary due to the difference in source. In this paper, performance of five different biodiesels was studied: CME, SME, RME, PME and WME. Engine power, fuel consumption, gaseous emissions and PM, DS and none soot fraction (NSF) were investigated in a Cummins ISBe6 Euro III diesel engine fueled with five biodiesels respectively and compared with the diesel fuel. Results revealed that using different biodiesels resulted in PM reductions ranging from 53% to 69%, which included DS reduction ranging from 79% to 83%. Observations showed that fuel oxygen content and viscosity had obvious effects on DS. Higher oxygen content biodiesels produced less DS at high load while lower viscosity biodiesels produced less DS at low load.

Beijing will implement the 4th stage emission regulations (equivalent to Euro IV) in 2008 ahead of other provinces or cites in China. Beijing Environmental Protection Bureau (EPB) organized petroleum corporations, automobile and engine manufactories as well as research institutes to test the adaptability of the fuels from Chinese refineries to the modern vehicles or engines on the road running conditions in China. In this paper, the effects of diesel fuel quality on combustion and emission of a Euro IV heavy-duty diesel engine as one part of the program were studied to provide technical data to stipulate the feasible diesel fuel standard, which should guarantee modern vehicles or engines to meet the 4th stage regulations. Eight kinds of diesel fuels with different properties, such as cetane number, distillation temperature (T90) and sulfur content, were tested on a Euro IV Cummins heavy-duty diesel engine with urea SCR after-treatment.

Beijing will implement the national 4th stage emissions standards (equivalent to Euro IV emissions standards) in advance in China from 2008. The objective of this study was to provide some technical support for proposing automotive gasoline fuel standards matching with the emission standards. In this paper, tests were conducted on two engines and one gasoline passenger vehicle meeting Euro III or IV emission standards to study the correlation between gasoline fuel properties and engine performances, including power, fuel consumption and emissions. Test results showed that the effect of octane number on engine power depended on engine technologies. High octane number had a negative effect on fuel consumption and emissions. As olefin content increased, the engine-out THC emissions decreased significantly. The vehicle test results also showed that high olefin content greatly reduced the tailpipe THC emissions.

According to China's “oil-poor, gas-litte, coal-rich” structure of energy resources, to promote the development of coal-based methanol fuel as a clean alternative to gasoline and diesel fuel is one of the most realistic options. So the adaptability of methanol gasoline blend fuel used in the gasoline engine and vehilce should be investigated. Engine load performance, engine out emission, air fuel ratio variation and combustion characteristics were tested in a PFI Euro III gasoline engine using gasoline, M10, M15, M20, M30 as fuel without any modification of the engine. Air fuel ratio, light-off temperature and load characteristics of catalystic conversion coefficient were also investigated. And effects of methanol content on fuel consumption and vehicle out emissions of a Euro - vehicle are analyzed.

Knocking is the main obstacle of increasing compression ratio to improve the thermal efficiency of gasoline engines. In this paper, the concept of stratified stoichiometric mixture (SSM) was proposed to suppress knocking in gasoline engines. The rich mixture near the spark plug increases the speed of the flame propagation and the lean mixture in the end gas suppresses the auto ignition. The overall air/fuel ratio keeps stoichiometric to solve the emission problem using three way catalysts (TWC). Moreover, both the rich zone and lean zone lead to soot free combustion due to homogeneous mixture. The effect on the knocking of homogeneous and stratified mixture was studied in a direct injection spark ignition (DISI) engine using numerical simulation and experimental investigation respectively.

Particle Number (PN) have already been a big issue for developing high efficiency internal combustion engines (ICEs). In this study, controlled spark-assisted stratified compression ignition (SSCI) with moderate end-gas auto-ignition was used for reducing PN in a high compression ratio gasoline direct injection (GDI) engine. Under wide open throttle (WOT) and Maximum Brake Torque timing (MBT) condition, high external cooled exhaust gas recirculation (EGR) was filled in the cylinder, while two-stage direct injection was used to form desired stoichiometric but stratified mixture. SSCI combustion mode exhibits two-stage heat release, where the first stage is associated with flame propagation induced by spark ignition and the second stage is the result of moderate end-gas auto-ignition without pressure oscillation at the middle or late stage of the combustion process.

Homogeneous Charge Induced Ignition (HCII) combustion is believed to be a promising approach to achieve clean and high efficiency combustion. HCII can be realized by using port-injection of the high-volatile fuel (gasoline) to prepare in-cylinder homogeneous charge and direct injection of the high-ignitable fuel (diesel) near the top dead center to control the start of combustion. In the current study, a numerical study was carried out to understand the mixing and auto-ignition process in HCII combustion. A multicomponent chemical kinetic mechanism for gasoline and diesel, consisting of n-heptane, iso-octane, ethanol, toluene, diisobutylene and n-decane, has been developed for predicting their ignition and oxidation. The final mechanism consists of 104 species and 398 reactions. This mechanism was validated with the experimental data of ignition delay times and laminar flame speeds for each component and real transportation fuels.

This research focuses on the potential of Homogeneous Charge Induced Ignition (HCII) combustion meeting the Euro V emission standard on a heavy-duty multi-cylinder engine using a simple after-treatment system. However, in our previous studies, it was found that the gasoline ratio was limited in HCII by the over-high compression ratio (CR). In this paper, the effects of reducing CR on the performances of HCII at medium and high loads were explored by experimental methods. It was found that by reducing CR from 18:1 to 16:1 the peak in-cylinder pressure and the peak pressure rise rate were effectively reduced and the gasoline ratio range could be obviously extended. Thus, the combustion and emission characteristics of HCII at medium and high loads were noticeably improved. Soot emissions can be significantly reduced because of the increase of premixed combustion ratio. The reduction could be over 50% especially at high load and high speed conditions.

A Homogeneous charge induced ignition (HCII) combustion, realized by in-cylinder fuel blending of gasoline and diesel fuel, was developed and carefully optimized, both on a single cylinder and a multi-cylinder light-duty diesel engines, for high thermal efficiency and near zero emissions in a wide engine-operation range up to IMEP of 1 MPa. The effects of mixing and chemical parameters of HCII combustion, which can be controlled by production-viable hard-ware using conventional gasoline and diesel fuel, include injection timing of diesel fuel, injection rate pattern of diesel fuel (such as split injection), the gasoline/diesel ratio, boost pressure and exhaust gas recirculation (EGR). Based on a single cylinder engine, the experimental result shows that the interaction of the mentioned control parameters plays decisive role in determination of exhaust emissions and thermal efficiency.

A catalyst surfaced on Ag/Al2O3 substrate for the selective catalyst reduction (SCR) of NOx by ethanol was evaluated in a diesel engine, and the effect of the catalyst on the reduction of NOx from the diesel engine under the EURO III ESC test modes was also investigated. The reductant injecting device was designed by means of computational fluid dynamics (CFD) analysis, and the engine test bench including the reductant injection system for the evaluation of the NOx-SCR catalyst performance was established. On the bench, the SCR catalyst with the ethanol reductant was tested at different temperatures and space velocities (SV), and integrated with an oxidation catalyst to reduce the diesel exhaust emissions of NOx, HC and CO. Under the conditions of the SV=30,000 h-1 and the exhaust temperature range of 350∼420°C, the NOx conversion efficiency is high over 90% and low beyond the temperature range.

A 1-Dimensional (1-D) model of fluid dynamic and chemistry kinetics following hot spot auto-ignition has been developed to simulate the process from auto-ignition to pressure wave propagation. The role of wall effect on the physical-chemical interaction process is numerically studied. A pressure wave is generated after hot spot auto-ignition and gradually damped as it propagates. The reflection of the wall forms a reflected pressure wave with twice the amplitude of the incident wave near the wall. The superposition of the reflected and forward pressure waves reinforces the intensity of the initial pressure wave. Wall effect is determined by the distance between the hot spot center and the cylinder wall. Hot spot auto-ignition near the wall easily initiates detonation under high-temperature and high-pressure conditions because pressure wave reflection couples with chemical reactions and propagates in the mixture with high reactivity.

Super knock which occurs in highly boosted spark ignition engines in low speed pre-ignition regime can lead to severe engine damage. However, super knock occurs occasionally, it is difficult to clearly identify the causes. The widely accepted assumption for the cause of this phenomenon is oil intrusion. Most of oils have been proved to have higher cetane number than n-heptane dose, indicating that the intruded oil is very liable to auto-ignition in a boosted engine. Although there have been reported the type of base oil and additive has significant effect on pre-ignition frequency, the oil induced super knock is still so far not supported by any direct evidence. This paper presents the effect of direct oil intrusion into cylinder on super knock. The experiment was carried out in a single cylinder engine. The diluted oil by gasoline with different ratio was directly injected into cylinder using a modified single-hole injector with 4MPa injection pressure.

Gasoline Compression Ignition has been widely studied in recent years. The in-cylinder stratified charge in gasoline Partially Premixed Compression Ignition (PPCI) can extend the high load range with lower pressure rise rate than Homogeneous Charge Compression Ignition (HCCI). However, it is still not clear that whether there is flame propagation in the gasoline compression igntion mode and how the flame propagation influences the combustion process and pollution formation. In order to investigate the effect of flame, several gasoline compression ignition cases, including the single-stage and two-stage heat release processes, are simulated with the KIVA-3V Release 2 code in this study. The G-equation is employed to account for flame propagation, and the reduced i-octane/n-heptane mechanism is used to handle the chemical reactions. The results show that the flame propagation exists in the combustion process and it can accelerate the heat release slightly.