Search Results

In this research, an optical system for the detection of the flame propagation under the non-knocking and knocking conditions is developed and applied to a mass produced four cylinder SI engine. The normal flames are measured and analyzed under the steady state operating conditions at various engine speeds. For knocking cycles, the flame front propagations before and after knock occurrence are simultaneously taken with cylinder pressure data. In non-knocking and knocking cycles, flame propagation shows cycle-by-cycle variations, which are quite severe especially in the knocking cycles. The normal flame propagations are analyzed at various engine speeds, and show that the flame front on the exhaust valve side becomes faster as the engine speed increases. According to the statistical analysis, knock occurence location and flame propagation process after knock can be categorized into five different types.

In this study, spark-ignition engine knock was studied experimentally. Cylinder pressure and cylinder block vibration of a four cylinder SI engine were measured. Knock characteristics, such as knock intensity, knock cycle percentage, knock occurrence crank angle, were determined from pressure and vibration signals using different analysis methods. Methods using band-pass filter, third derivative and step method, which was developed in this study, were shown to be the most suitable. The step method only used signals above threshold value during knocking and, as a result, both pressure and vibration signal analysis results with this method showed good signal-to-noise ratio. The knock intensities calculated from cylinder pressure and block vibration were proportional to each other over a wide range. It was confirmed in this study that vibration signals were useful in knock detection.

Knock control algorithms were developed for a spark-ignition engine. Spark timing was controlled using cylinder block vibration signal. The vibration signal of a 1.5 L four cylinder spark-ignition engine was measured using an accelerometer which was attached to the cylinder block. The maximum amplitude of the bandpass-filtered accelerometer signals was used as the knock intensity. Three different spark-ignition engine knock control algorithms were tested experimentally. Two algorithms were conventional algorithms in which knock threshold values were predetermined for each engine condition. Spark timing was retarded and advanced depending on the knock intensity in one algorithm and the knock occurrence interval in the other algorithm. The third algorithm was a new algorithm in which knock threshold values were automatically corrected by monitoring knock condition.

Spark-ignition engine knock was characterized in terms of when during the engine cycle and combustion process knock occurred and its magnitude or intensity. Cylinder pressure data from a large number of successive individual cycles were generated from a single-cylinder engine of hemispherical chamber design over a range of operating conditions where knock occurred in some or all of these cycles. Mean values and distributions of following parameters were quantified: knock occurrence crank angle, knock intensity, combustion rate and the end-gas thermodynamic state. These parameters were determined from the cylinder pressure data on an individual cycle basis using a mass-burn-rate analysis. The effects of engine operating variables on these parameters were studied, and correlations between these parameters were examined.

CARS temperature measurements were carried out both in a constant volume combustion chamber and in a spark-ignition engine. The CARS temperature measurement under engine-like condition was validated by comparing the unburned gas temperatures for premixed propane-air flame in a constant volume combustion chamber obtained by CARS with predicted temperatures of 2-zone flame propagation simulation model. There was good agreement between the predicted temperatures and the mean values of 10 CARS measurements. The standard deviation of 10 measurements at each measuring timing was about ±40 K. End-gas temperatures were measured by CARS technique in a conventional 4-cylinder DOHC spark-ignition engine with the engine motoring and firing. The measured motoring temperature matched well with the adiabatic core temperature calculated from the measured cylinder pressure. The engine was fueled with primary reference fuel (PRF80) of 80% iso-octane and 20% n-heptane by volume.

A combined experimental and analytical approach was followed in this work to study stress distributions and causes of failure in diesel cylinder heads under steady-state and transient operation. Experimental studies were conducted first to measure temperatures, heat fluxes and stresses under a series of steady-state operating conditions. Furthermore, by placing high temperature strain gages within the thermal penetration depth of the cylinder head, the effect of thermal shock loading under rapid transients was studied. A comparison of our steady-state and transient measurements suggests that the steady-state temperature gradients and the level of temperatures are the primary causes of thermal fatigue in cast-iron cylinder heads. Subsequently, a finite element analysis was conducted to predict the detailed steady-state temperature and stress distributions within the cylinder head. A comparison of the predicted steady-state temperatures and stresses compared well with our measurements.