Criteria

Text:
Display:

Results

Viewing 1 to 30 of 146
CURRENT
2011-10-27
Standard
J1580_201110
this document is to be used on cutting edges and end bits in conjunction with metric bolts (reference ISO 7852-1982) typically used on off-road, self-propelled work machines as described in SAE J1116. The cutting edges are further defined in SAE J737, J739, J1304, and J1581. The end bits are further defined in SAE J63.
HISTORICAL
1989-12-01
Standard
J1580_198912
This document is to be used on cutting edges and end bits in conjunction with metric bolts (Reference ISO 7852-1982) typically used on off-road, self-propelled work machines as described in SAE J1116. The cutting edges are further defined in SAE J737, J739, J1304, and J1581. The end bits are futher defined in SAE J63. This document specifies the principle shapes and dimensions for countersunk square holes.
HISTORICAL
2002-10-31
Standard
J1197_200210
This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.
CURRENT
2011-10-27
Standard
J1197_201110
This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions.
HISTORICAL
1991-02-01
Standard
J1197_199102
This SAE Recommended Practice applies to wheel and crawler loaders when equipped with log or material handling forks without vertical masts, taking only hydraulic lift capacity and operating stability into consideration. It is recognized that specific operating conditions may allow larger, or require smaller, loads than the rated operating load. some conditions would require more careful or restricted operation with the rated operating load. This practice is not to be construed as setting up test procedures or conditions. This document establishes the definition of a normal all day rated operating load for loaders as defined in SAE J/ISO 6165.
1993-09-01
Standard
J874_199309
This SAE Standard specifies a method for determining the coordinates of the center of gravity of earthmoving machinery such as tractors, loaders, dumpers, and graders in any condition of loading or position of attachments.
2003-05-08
Standard
J874_200305
This SAE Standard specifies a method for determining the coordinates of the center of gravity of earthmoving machinery such as tractors, loaders, dumpers, and graders in any condition of loading or position of attachments.
1985-10-01
Standard
J874_198510
This SAE Standard specifies a method for determining the coordinates of the center of gravity of earthmoving machinery such as tractors, loaders, dumpers, and graders in any condition of loading or position of attachments.
1986-03-01
Standard
J874_198603
This SAE Standard specifies a method for determining the coordinates of the center of gravity of earthmoving machinery such as tractors, loaders, dumpers, and graders in any condition of loading or position of attachments.
1977-06-01
Standard
J874A_197706
This SAE Standard specifies a method for determining the coordinates of the center of gravity of earthmoving machinery such as tractors, loaders, dumpers, and graders in any condition of loading or position of attachments.
CURRENT
2003-05-08
Standard
J872_200305
This SAE Standard specifies a test method to measure the drawbar pull performance of self-propelled construction, forestry, and industrial machines and their combinations with mounted and/or trailed equipment, with or without payload, as listed in SAE J1116. It covers the following criteria measured against travel speed: drawbar pull, drawbar power, and wheel or track slip.
HISTORICAL
1986-05-01
Standard
J872_198605
This SAE Standard specifies a test method to measure the drawbar pull performance of self-propelled construction, forestry, and industrial machines and their combinations with mounted and/or trailed equipment, with or without payload, as listed in SAE J1116. It covers the following criteria measured against travel speed: drawbar pull, drawbar power, and wheel or track slip.
HISTORICAL
2006-02-05
Standard
J740_200602
This standard specifies the principal shapes and dimensions for countersunk square holes. To be used on cutting edges and end bits in conjunction with No. 3 head plow bolts (Ref. ANSI B18.9) typically used on off-road self-propelled work machines as described in SAE J1116. Cutting edges are further in SAE J737, J739 and J1304. End bits are further defined in SAE J63.
CURRENT
2011-10-25
Standard
J740_201110
To be used on cutting edges and end bits in conjunction with No. 3 head plow bolts (Ref. ANSI B18.9) typically used on off-road self-propelled work machines as described in SAE J1116. Cutting edges are further defined in SAE J737, J739 and J1304. End bits are further defined in SAE J63. When section thickness exceeds A in drawing 1 (Figure 2) (countersunk one side) or B in drawing 4 (countersunk both sides), use counterbore with diameter D, as shown in cross section drawings 2, 5 and 6, or extended countersink C, as shown in cross section drawings 3 and 7. The inscribed circle of the square holes shall be concentric with countersink or counterbore within 0.03 in (0.8 mm).
HISTORICAL
2006-02-05
Standard
J739_200602
This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580. This document specifes hole placement along the length and width of the cutting edge and dimensions for cutting edge cross sections. See Table 1.
CURRENT
2007-08-30
Standard
J739_200708
This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580. This document specifes hole placement along the length and width of the cutting edge and dimensions for cutting edge cross sections. See Table 1.
HISTORICAL
1986-07-01
Standard
J740_198607
This standard specifies the principal shapes and dimensions for countersunk square holes. To be used on cutting edges and end bits in conjunction with No. 3 head plow bolts (Ref. ANSI B18.9) typically used on off-road self-propelled work machines as described in SAE J1116. Cutting edges are further in SAE J737, J739 and J1304. End bits are further defined in SAE J63.
CURRENT
2002-02-21
Standard
J733_200202
This Standard is to establish identification terminology for major components and parts used in the ripping operation on earthmoving machines. The components and parts illustrated are attached to certain self-propelled earthmoving machines and/or attachments as defined in SAE J326, J727, J729, J870 and J1193.
HISTORICAL
1991-06-01
Standard
J739_199106
This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580. This document specifes hole placement along the length and width of the cutting edge and dimensions for cutting edge cross sections. See Table 1.
HISTORICAL
1986-06-01
Standard
J739_198606
This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580. This document specifes hole placement along the length and width of the cutting edge and dimensions for cutting edge cross sections. See Table 1.
HISTORICAL
1978-05-01
Standard
J49_197805
1.1 This standard applies to hydraulic backhoes which have no more than 190 degrees of rotational swing, and are mounted on wheel tractors and crawler tractors. 1.2 Purpose The purpose of the standard is to establish a uniform method of providing dimensional and operational specifications for hydraulic backhoes. Dimensional and operational specifications are determined without assembly or equipment changes such as buckets, dippersticks, etc. When specifications are affected by adjustable or extendable members, the position must be specified. 4.2.1 – 6.2 are further defined by Figures 1–8. Figures 1–8 are not intended to be descriptive of any existing machine and are used only to clarify the meaning of the standard.
CURRENT
2012-07-16
Standard
J49_201207
This standard applies to hydraulic backhoes which have no more than 190 degrees of rotational swing, and are mounted on wheel tractors and crawler tractors.
HISTORICAL
1980-04-30
Standard
J49_198004
The purpose of this standard is to establish a uniform method of providing dimensional operational specifications for hydraulic backhoes. This standard includes the definitions of specification most commonly used to describe nonfull-rotating hydraulic backhoes. Dimensional and operational specifications are to be determined without assembly or equipment changes such as buckets, dippersticks, etc. When specifications are affected by adjustable or extendable members, the position must be specified. Paragraphs 4.2.1-6.2 are further defined by Figs. 1-8. Figs 1-8 are not intended to be descriptive of any existing machine and are used only to clarify the meaning of the standard.
CURRENT
2002-02-21
Standard
J749_200202
This SAE Standard provides recommended dimensions for drawbars for crawler tractors as defined in SAE J1057 (SEP88). It includes only those dimensions which will affect the attaching of towed equipment.
HISTORICAL
1983-12-01
Standard
J749_198312
This SAE Standard provides recommended dimensions for drawbars for crawler tractors as defined in SAE J1057 (SEP88). It includes only those dimensions which will affect the attaching of towed equipment.
HISTORICAL
1984-12-01
Standard
J1016_198412
This SAE Standard provides names of major components peculiar to dumpers as defined in SAE J1057 (See Figure 1). Illustrations of components are not intended to be exactly descriptive of any particular machine. For component nomenclature for dumper trailers, refere to SAE J734.
HISTORICAL
1990-07-01
Standard
J1016_199007
This SAE Standard provides names of major components peculiar to dumpers as defined in SAE J1057 (See Figure 1). Illustrations of components are not intended to be exactly descriptive of any particular machine. for component nomenclature for dumper trailers, refere to SAE J734.
HISTORICAL
1986-01-01
Standard
J1017_198601
This SAE Standard provides names of major components peculiar to rollers and compactors. Illustrations of components are not intended to be exactly descriptive of any particular machine. NOTE: Rollers and compactors will be defined in a section added to SAE J1057a.
CURRENT
2000-06-28
Standard
J1016_200006
This SAE Standard provides names of major components peculiar to dumpers as defined in SAE J1057 (See Figure 1). Illustrations of components are not intended to be exactly descriptive of any particular machine. For component nomenclature for dumper trailers, refere to SAE J734.
CURRENT
2011-10-27
Standard
J1017_201110
This SAE Standard provides names of major components peculiar to rollers and compactors. Illustrations of components are not intended to be exactly descriptive of any particular machine. NOTE: Rollers and compactors will be defined in a section added to SAE J1057a.
Viewing 1 to 30 of 146