Search Results

The passenger car automakers are always competing to excel in vehicle characteristics related to passenger comfort and driveability aspects. The engine calibration is a theoretical and experimental procedure with the intention to extract maximum efficiency from the engine and guarantee satisfactory levels of driving for both conventional and racing cars. This paper describes the calibration procedure of a Formula SAE race car engine. The engine was a four cylinder 600 cm3 four-strokes with modified intake and exhaust systems, controlled by an engine control unit (Motec M800 ECU). These engines present optimized characteristics for high speed, in exchange for some combustion degradation in some specific operating conditions at low speed that may impair vehicle driveability. Therefore, good tip-in reaction and the progression of the torque delivery are fundamental criteria to increase the vehicle performance, specially, to those submitted to short acceleration distances.

Controlled Auto-Ignition (CAI), also known as HCCI (Homogeneous Charge Compression Ignition), is increasingly seen as a very effective way of lowering both fuel consumption and emissions from gasoline engines. Therefore, it's seen as one of the best ways to meet future engine emissions and CO2 legislations. This combustion concept was achieved in a Ford production, port-injected, 4 cylinder gasoline engine. The only major modification to the original engine was the replacement of the original camshafts by a new set of custom made ones. The CAI operation was accomplished by means of using residual gas trapping made possible by the use of VCT (variable cam timing) on both intake and exhaust camshafts. When running on CAI, the engine was able to achieve CAI combustion with in a load range of 0.5 to 4.5 BMEP, and a speed range of 1000 to 3500 rpm. In addition, spark assisted CAI operation was employed to extend the operational range of low NOx and low pumping loss at part-load conditions.

Controlled Auto-Ignition (CAI) also known as Homogeneous Charge Compression Ignition (HCCI) is increasingly seen as a very effective way of lowering both fuel consumption and emissions. Hence, it is regarded as one of the best ways to meet stringent future emissions legislation. It has however, still many problems to overcome, such as limited operating range. This combustion concept was achieved in a production type, 4-cylinder gasoline engine, in two separated tests: naturally aspirated and turbocharged. Very few modifications to the original engine were needed. These consisted basically of a new set of camshafts for the naturally aspirated test and new camshafts plus turbocharger for the test with forced induction. After previous experiments with naturally aspirated CAI operation, it was decided to investigate the capability of turbocharging for extended CAI load and speed range.

Ethanol with high levels of hydration is a low cost fuel that offers the potential to replace fossil fuels and contribute to lower carbon dioxide (CO2) emissions. However, it presents several ignition challenges depending on the hydration level and ambient temperature. Advanced combustion concepts such as homogeneous charge compression ignition (HCCI) have shown to be very tolerant to the water content in the fuel due to their non-flame propagating nature. Moreover, HCCI tends to increase engine efficiency while reducing oxides of nitrogen (NOx) emissions. In this sense, the present research demonstrates the operation of a 3-cylinder power generator engine in which two cylinders operate on conventional diesel combustion (CDC) and provide recycled exhaust gas (EGR) for the last cylinder running on wet ethanol HCCI combustion. At low engine loads the cylinders operating on CDC provide high oxygen content EGR for the dedicated HCCI cylinder.

The possibility to vary compression ratio offers a new degree of freedom that may enable so far not exploited benefits for the combustion process especially for highly boosted spark ignited engines. Numerous approaches to enable a variable compression ratio (VCR) have been tried and tested in the past. Nevertheless, none of these systems reached series production because of several reasons, ranging from too much complexity and moveable parts to deep modification required on existing engine architectures and manufacturing lines. Instead, the approach of a variable length conrod (VCR conrod) could be the solution for integration in almost any type of engine with minor modifications. It is then considered by several OEMs as a promising candidate for midterm series production. This paper shows, firstly, a discussion of the benefits of a variable compression ratio system.

Stringent emission legislations have pushed engine operation to borderline knock. Knocking combustion limits engine efficiency, putting a threshold in carbon emission reduction that impairs further decarbonization of the transport sector. In this way, online knock monitoring is very important during engine development and calibration to allow operation with higher efficiency levels. Commonly, knock detection methods require complex calculations with high computational cost. Furthermore, these methods normally need previous calibration of a threshold value for each specific engine to indicate the knock limit, requiring important engineering resources and time. Hence, this paper proposes a novel methodology for knock detection that is simple, does not require prior calibration and can be used for sensorless knock detection. The method is applied by relating the crank angle of maximum pressure rise rate (AMPRR) with the angle of 50% of fuel mass burned (CA50), the so-called G Index (GI).

Low cost ethanol with high levels of hydrations is a fuel that can be easily produced and that offers the potential to replace fossil fuels and contribute to reduce greenhouse gas emissions. However, it shows several ignition challenges depending on the hydration level, ambient temperature compression ratio and other engine-specific aspects. Advanced combustion concepts such as homogeneous charge compression ignition (HCCI) have shown to be very tolerant to the water content in the fuel due to their non-flame propagating nature. Moreover, HCCI tends to increase engine efficiency while reducing oxides of nitrogen (NOx) emissions. In this sense, the present research demonstrates the operation of a 3-cylinder power generator engine in which two cylinders operate on conventional diesel combustion (CDC) and provide recycled exhaust gas (EGR) for the last cylinder running on wet ethanol HCCI combustion.

Experimental aviation engines face numerous challenges, including the need for energy efficiency, alternative fuel sources, reduced weight and size, greater durability with reliability, emissions reduction, and integration with advanced control and monitoring systems. This study presents the performance of a two-stroke engine with a Uniflow scavenging system with a flathead valve concept, with lower specific fuel consumption than conventional two-stroke aircraft engines. The engine’s maximum speed is limited to 3000 rpm for better cylinder scavenging efficiency, which also eliminates the need for a reduction gearbox, simplifies the design, and reduces the engine’s total mass. 1D simulations were conducted to evaluate combustion and performance parameters using aviation.