Search Results

It is well known that lubricating oil consumption (LOC) is much affected by the cylinder bore deformation occurring within internal combustion engines. There are few analytical reports, however, of this relationship within internal combustion engines in operation. This study was aimed at clarifying the relationship between cylinder bore deformation and LOC, using a conventional in-line four-cylinder gasoline engine. The rotary piston method developed by the author et al. was used to measure the cylinder bore deformation of the engine’s cylinder #3 and cylinder #4. In addition, the sulfur tracer method was applied to measure LOC of each cylinder. LOC was also measured by changing ring tension with a view to taking up for discussion how piston ring conforms to cylinder, and how such conformability affects LOC. Their measured results were such that the cylinder bore deformation was small in the low engine load area and large in the high engine load area.

This paper deals with the friction performance results for various new concept piston skirt profiles. The program was conducted under the assumption that friction performance varies by the total amount of oil available at each crank angle in each stroke and the instantaneous distribution of the oil film over the piston skirt area. In previous papers [1,2] it was that lower friction designs would be expected to show higher skirt slap noise. This paper discusses the correlation between friction and skirt slap for each new concept profile design. Finally, this paper explains the friction reduction mechanism for the test samples for each stroke of the engine cycle by observing the skirt movement and oil lubrication pattern using a visualization engine.

Aiming at the improvement in piston lubrication and the reduction of piston friction loss under this study, piston friction forces of cylinders with different surface roughness and treatment methods have been measured by means of a floating liner method, and the piston surface conditions have been also observed. As a result, it is found that the piston lubrication can be markedly improved by reducing the cylinder surface roughness. It is also verified that the deterioration in lubrication can be reduced even if some low viscosity oil is used, and the effect on the friction loss reduction becomes greater by reducing the piston surface roughness. On the other hand, it is found that many small vertical flaws are generated on the cylinder surface by reducing the surface roughness. In order to cope with this problem, etching and DLC (Diamond Like Carbon) coating have been tested as the surface treatments. As a result, it is confirmed that DLC coating is effective for the above.

This study has been conducted aiming at reductions of piston slap noise and piston friction loss, and effects of lubricating oil supply between the piston skirt and cylinder on diesel engine have been verified through a series of experiments. Namely, lubricating oil was supplied forcibly into the piston skirt from outside of engine, and its effects on the cylinder block vibration, piston friction force, slap motion and oil consumption have been measured. As a result, it has been verified that the supply of a small amount of oil (6mL/min) to the piston skirt reduces about 50 % of the block vibration caused by the piston slap motion in idling operation, and about 20 % of the piston friction loss in full load operation. Furthermore it has verified without giving any significant adverse effect on oil consumption.

Frictional force as a function of crank angle of a piston assembly and piston rings alone were measured after the following devices were developed. (1) A gas sealing device that did not affect the measuring values. (2) A device to minimize the effect of gas pressure on the cylinder head and block deformations. (3) A device to minimize the effect of piston slap force. From the measurement of the frictional force diagrams the following characteristics have been found. (1) Lubricating oil temperature has the greatest effect upon the frictional loss of the piston. (2) Piston friction does not increase to the point of becoming proportional to the engine speed. (3) Friction in the expansion stroke increases at high load by the piston slap phenomenon. But the increase of total losses are small because the duration is short. (4) Piston rings account for the majority of the entire frictional force of the piston.

A hydrogen powered vehicle system consisted of LH2 tank high pressure LH2 -pump, a device to inject hydrogen onto the hot surface, and ignitor in turbo-engine of CR 12:1 had been developed by Musashi Institute of Technology- Recently the authors applied this system to a medium duty truck produced by Hino Motors Ltd. Then following improvement were required. (1) Gas tightness and endurance of hydrogen injector were improved by the selection of material, size, finishing and by suppling a small amount of lubricating oil. (2) Mixture formation of the injected hydrogen with the compressed air was improved by tuning up the size and number of the nozzle holes and injection timing with the hydraulic pump and valve. (3) A small amount of hydrogen was supplied into the intake manifold. It reduced the combustion noise and also it recovered the evaporation loss in the LH2 -tank.

Exhaust-gas recirculation (EGR) causes the piston ring and cylinder liners of a diesel engine to suffer abnormal wear. The present study aimed at making clear the mechanism of wear which is induced by soot in the EGR gas. The piston ring has been chrome plated and the cylinder was made of boron steadite cast iron. Detailed observations of the ring sliding surfaces and that of the wear debris contained in lubricating oil were carried out. As a result, it was found that the wear of the top ring sliding surfaces identify abrasive wear without respect to the presence of EGR by steadite on the cylinder liner sliding surface. In addition, it is confirmed in a cutting test that soot mixed lubricating oil improved in performance as cutting oil. Based on these results, we proposed the hypothesis in the present study that ring wear is accelerated at EGR because abrasive wear increases due to a lot of soot mixed into lubricating oil improving the performance of lubricating oil as cutting oil.

The effect of local lubricant viscosity on the temperature and thickness of oil film on a piston ring in a diesel engine is analyzed by using the Reynolds equation, and unsteady and two-dimensional energy equation with heat generated from viscous dissipation. The oil film viscosity for a multi-grade oil is then estimated by using the local oil film temperature and the local shear rate. Moreover, the heat transfer between ring and liner surfaces is examined. The oil film thickness calculated from this method is lesser than that of the case where the viscosity is based on the liner temperature and the mean shear rate. Maximum values of heat transfer at the ring and liner surfaces are obtained at the vicinity of crank angle where the oil film thickness is at a minimum.

Due to increasing economic and environmental performance requirements of internal combustion engines, piston manufacturers now focus more on lower friction designs. One factor strongly influencing the friction behavior of pistons is the dynamic interaction between lubricating oil, cylinder bore and piston. Therefore, the dynamic effect of the oil film in the gap between the liner and piston has been studied, using a single cylinder engine equipped with a sapphire window. This single cylinder engine was also equipped with a floating liner, enabling real-time friction measurement, and directly linking the oil film behavior to friction performance of pistons.

This paper describes a measurement method using laser induced fluorescence we have developed for simple simultaneous measurements of piston ring oil film thickness at plural points for internal combustion engines. The findings obtained by the measurements of oil film thickness on both thrust and anti-thrust sides of the piston for a mono-cylinder compact diesel engine using this new measurement method are also discussed in this paper. One of main findings is that the oil film thickness of each ring on both sides differs markedly in terms of the absolute value and the stroke- to-stroke variation. It is found that this difference in oil film thickness is caused by the difference in the amount of lubricating oil supplied to the oil ring, and the effect is greater than that of engine speed or load.