Search Results

The influence of ethanol blending in Diesel fuel on the spray and spray combustion characteristics was investigated by performing experiments in an optically accessible high-pressure / high-temperature spray chamber under non-evaporating, evaporating and combusting conditions. Three fuels were investigated: (1) Diesel - a European Diesel based on the EN590 standard; (2) E10 - a blend of Diesel containing 10% ethanol and 2% emulsion additive; and (3) E20 - a blend of Diesel containing 20% ethanol and 2% emulsion additive. A constant gas density of 24.3 kg/m3 was maintained under non-evaporating (30 °C, 21.1 bar), evaporating (350 °C, 43.4 bar), low combustion temperature (550 °C, 57.3 bar) and high combustion temperature (600 °C, 60 bar) conditions. A single-hole injector with a nozzle diameter of 0.14 mm was used and injection pressure was held constant at 1350 bar. Various optical methods were used to characterize the non-combusting and combusting sprays.

Future requirements for emission reduction from combustion engines in ground vehicles might be met by using the HCCI combustion concept. In this study, negative valve overlap (NVO) and low lift, short duration, camshaft profiles, were used to initiate HCCI combustion by increasing the internal exhaust gas recirculation (EGR) and thus retaining sufficient thermal energy for chemical reactions to occur when a pilot injection was introduced prior to TDC, during the NVO. One of the crucial parameters to control in HCCI combustion is the combustion phasing and one way of doing this is to vary the relative ratio of fuel injected in pilot and main injections. The combustion phasing is also influenced by the total amount of fuel supplied to the engine, the combustion phasing is thus affected when the load is changed. This study focuses on the reactions that occur in the highly diluted environment during the NVO when load and pilot to main ratio are changed.

Future demands for improvements in the fuel economy of gasoline passenger car engines will require the development and implementation of advanced combustion strategies, to replace, or combine with the conventional spark ignition strategy. One possible strategy is homogeneous charge compression ignition (HCCI) achieved using negative valve overlap (NVO). However, several issues need to be addressed before this combustion strategy can be fully implemented in a production vehicle, one being to increase the upper load limit. One constraint at high loads is the combustion becoming too rapid, leading to excessive pressure-rise rates and large pressure fluctuations (ringing), causing noise. In this work, efforts were made to reduce these pressure fluctuations by using a late injection during the later part of the compression. A more appropriate acronym than HCCI for such combustion is SCCI (Stratified Charge Compression Ignition).

Laws concerning to emissions from heavy duty (HD) internal combustion engines are becoming increasingly stringent. New engine technologies are therefore needed to satisfy these new legal requirements and reduce fossil fuel dependency. One way to achieve both objectives is to partially replace fossil fuels with alternatives that are more sustainable with respect to emissions of greenhouse gas, particulates and NOx. As a first step towards the development of a direct injected dual fuel engine using diesel fuel and renewable alcohols such as methanol or ethanol, we have studied ethanol (E100) sprays generated with a standard high pressure diesel fuel injection system in a high pressure/temperature spray chamber with optical access. The experiments were performed at a gas density of ∼27kg/m3 at ∼550 °C and ∼60 bar, representing typical operating conditions for a HD engine at low loads.

Soot particle size, particle concentration and volume fraction were measured by laser based methods in optically dense, highly turbulent combusting diesel sprays under engine-like conditions. Experiments were done in the Chalmers High Pressure, High Temperature spray rig under isobaric conditions and combusting commercial diesel fuel. Laser Induced Incandescence (LII), Elastic Scattering and Light Extinction were combined quasi-simultaneously to quantify particle characteristics spatially resolved in the middle plane of a combusting spray at two instants after the start of combustion. The influence that fuel injection pressure, gas temperature and gas pressure exert on particle size, particle concentration and volume fraction were studied. Probability density functions of particle size and two-dimensional images of particle diameter, particle concentration and volume fraction concerning instantaneous single-shot cases and average measurements are presented.

Spray characteristics of fossil Diesel fuel, hydrotreated vegetable oil (HVO) and two oxygenated fuel blends were studied to elucidate the combustion process. The fuels were studied in an optically accessible high-pressure/high-temperature chamber under non-combusting (623 K, 4.69 MPa) and combusting (823 K, 6.04 MPa) conditions. The fuel blends contained the long-chain alcohol 2-ethylhexanol (EH), HVO and either 20 vol.% Diesel or 7 vol.% rapeseed methyl ester (RME) and were designed to have a Diesel-like cetane number (CN). Injection pressures were set to 120 MPa and 180 MPa and the gas density was held constant at 26 kg/m3. Under non-combusting conditions, shadow imaging revealed the penetration length of the liquid and vapor phase of the spray. Under combusting conditions, the lift-off length and soot volume fraction were measured by simultaneously recording time-resolved two-dimensional laser extinction, flame luminosity and OH* chemiluminescence images.

The effects of using n-butanol, n-octanol, fossil Diesel, hydrotreated vegetable oil (HVO), and blends of these fuels on spray penetration, flame and soot characteristics were investigated in a high-pressure high-temperature constant volume combustion chamber designed to mimic a heavy duty Diesel engine. Backlight illumination was used to capture liquid and vapor phase spray images with a high-speed camera. The flame lift-off length (LOL) and ignition delay were determined by analyzing OH* chemiluminescence images. Laser extinction diagnostics were used to measure the spatially and temporally resolved soot volume fraction. The spray experiments were performed by injecting fuels under non-combusting (623 K) and combusting (823 K) conditions at a fixed ambient air density of 26 kg/m3. A Scania 0.19 mm single straight hole injector and Scania XPI common rail fuel supply system were used to produce injection pressures of 120 MPa and 180 MPa.

Natural gas, biogas, and biomethane are attractive fuels for compressed natural gas (CNG) engines because of their beneficial physical and chemical characteristics. This paper examines three combustion modes - homogeneous stoichiometric, homogeneous lean burn, and stratified combustion - in an optical single cylinder engine with a gas direct injection system operating with an injection pressure of 18 bar. The combustion process in each mode was characterized by indicated parameters, recording combustion images, and analysing combustion chemiluminescence emission spectra. Pure methane, which is the main component of CNG (up to 98%) or biomethane (> 98 %), was used as the fuel. Chemiluminescence emission spectrum analysis showed that OH* and CN* peaks appeared at their characteristic wavelengths in all three combustion modes. The peak of OH* and broadband CO2* intensities were strongly dependent on the air/fuel ratio conditions in the cylinder.

A method for measuring apparent soot particle size and concentration in turbulent combusting diesel jets with elevated and inhomogeneous optical density is presented and discussed. The method is based on the combination of quasi-simultaneous Laser Induced Incandescence (LII), Elastic Scattering (ELS) and Light Extinction (LE) measurements exhibiting a high potential for spatially resolved measurements of carbonaceous particles in flames and residual gases at a given instant. The method evaluates the LII signal by calculating the laser fluence across the flame and compensating for signal trapping, allowing measurements where laser extinction between the flame borders reaches values up to 90%. The method was implemented by measuring particle size and concentration in the middle sagittal axis of optically dense, combusting diesel jets at a certain time after the start of combustion.