Search Results

Current energy policies are encouraging the near-term use of fuels derived from civil and industrial waste residues, giving new perspectives for their disposal. The possibility of using, in Diesel engines, a liquid fuel derived from waste synthetic polymeric matrices, such as scrap tyres, is evaluated in this paper. The fuel is obtained by means of an innovative technology based on a thermo-mechanical cracking process at moderate temperatures and pressures. A preliminary investigation was carried out on a 440 cm3 single-cylinder Diesel engine for stationary applications using a commercial automotive Diesel fuel (UNI-EN 590:2010) and two mixtures of automotive Diesel fuel and tyre pyrolysis oil (TPO): the first one containing 20% TPO by volume, the other containing 40% TPO.

Homogeneous charge compression ignition (HCCI) combustion is considered to be an attractive alternative to traditional internal combustion engine operation because of its extremely low levels of pollutant emissions. However, there are several difficulties that must be overcome for HCCI practical use, such as difficult ignition timing controllability. Indeed, too early or too late ignition can occur with obvious drawbacks. In addition, the increase in cyclic variation caused by the ignition timing uncertainty can lead to uneven engine operation. As a way to solve the combustion phasing control problem, dual-fuel combustion has been proposed. It consists of a diesel pilot injection used to ignite a pre-mixture of gasoline (or other high octane fuel) and air. Although dual-fuel combustion is an attractive way to achieve controllable HCCI operation, few studies are available to help the understanding of its in-cylinder combustion behavior.

The paper describes the CFD analysis, the arrangement and the first experimental results of a single-cylinder engine that employs an innovative low-pressure hydrogen direct-injection system, characterized by low fuel rail pressure (12 bar) and consequent low residual storage pressure. The injection is split in two steps: at first hydrogen is metered and admitted into a small intermediate chamber by an electroinjector (a conventional one usually employed for CNG), next a mechanically actuated poppet valve, that allows high volumetric flow rates, times hydrogen injection from the intermediate chamber to the cylinder within a short time, despite the high hydrogen volume due to the low injection pressure. Injection must be properly timed to maintain pressure below 6 bar (or little more) in the intermediate chamber and thus keep sonic flow through the electroinjector, to maximize volumetric efficiency and to avoid backfire in the intake pipe.

An innovative hydrogen DI system was conceived, realized and tested that requires only 12 bar rail pressure, typical value of PFI systems, and does not need special injectors. The purpose is to combine the well-known benefits of DI with the ones of PFI. The injection is accomplished in two steps: at first hydrogen, metered by an electroinjector (a conventional one for CNG application), enters a small intermediate chamber; then it is injected into the cylinder by means of a mechanically actuated valve that allows very high flow rate (compared with the one of electroinjectors). In-cylinder injection starts at intake valve closing (an earlier injection start could lead to backfire) and stops early enough to allow proper charge homogeneity and, in any case, before cylinder pressure rise constrains hydrogen admission. The prototype engine was realized modifying a production single-cylinder 650 cm₃ engine with three intake valves.

The paper deals with experimental activity concerning ATAC, which, in two-stroke gasoline engines, helps solving the crucial problem of combustion instability at light loads. ATAC consists of employing the energy of residual gas to prime an efficient combustion. The research is aimed to give further insight into ATAC mechanism both by visualisation of the combustion process and by examination of the influence which relevant parameters like air-fuel ratio, engine speed, compression ratio, scavenging passage design have on ATAC operation. Several results have been acquired and collected hitherto. A part of them are shown and discussed in this paper.

High-pressure liquid fuel injection is a suitable means to get either stratified charge or homogeneous charge for two-stroke engines. This paper shows the development of this solution for a small 50 cm3 engine for light motorcycles. By means of computational fluid dynamics, a combustion chamber suitable for proper fuel distribution in every engine operating condition has been designed. It has been realized, and experimental results confirm its fairly satisfactory behaviour, with good fuel economy, low exhaust emissions and small cycle-to-cycle variation even at light loads. Recent CFD studies indicate how to improve engine geometry to achieve a better stratification stability at partial loads independently on engine speed.

Storing hydrogen is one of the major problems concerning its utilization on board vehicles. Today hydrogen can be compressed and stored at 200 or 350 bar (it is foreseen that in a near future storage pressure will reach 700 bar, according to new expected regulations and using tanks in composite materials) or cryogenically liquefied. An alternative solution is storing hydrogen in the form of ammonia that is liquid at roughly 9 bar at environmental temperature and therefore involves relatively small masses and volumes and requires light and low-cost tanks. Moreover, ammonia contains almost 18% hydrogen by mass and, by volume, liquid ammonia contains 1.7 times as much hydrogen as liquid hydrogen. It is well known that ammonia can be burned directly in I.C. engines, however a combustion promoter is necessary to support combustion especially in the case of high-speed S.I. engines.

Storing hydrogen is one of the major issues concerning its utilization on board vehicles. A promising solution is storing hydrogen in the form of ammonia that contains almost 18% hydrogen by mass and is liquid at roughly 9 bar at environmental temperature. As a matter of fact, liquid ammonia contains 1.7 times as much hydrogen as liquid hydrogen itself, thus involving relatively small volumes and light and low-cost tanks. It is well known that ammonia can be burned directly in I.C. engines, however a combustion promoter is necessary to support and speed up combustion especially in the case of high-speed S.I. engines. The best promoter is hydrogen, due to its opposed and complementary characteristics to those of ammonia, Hydrogen has high combustion velocity, low ignition energy and wide flammability range, whereas ammonia has low flame speed, narrow flammability range, high ignition energy and high self-ignition temperature.