Search Results

The turbulent flow field inside the cylinder plays a major role in spark ignition (SI) engines. Multiple phenomena that occur during the high pressure part of the engine cycle, such as early flame kernel development, flame propagation and gas-to-wall heat transfer, are influenced by in-cylinder turbulence. Turbulence inside the cylinder is primarily generated via high shear flows that occur during the intake process, via high velocity injection sprays and by the destruction of macro-scale motions produced by tumbling and/or swirling structures close to top dead center (TDC) . Understanding such complex flow phenomena typically requires detailed 3D-CFD simulations. Such calculations are computationally very expensive and are typically carried out for a limited number of operating conditions. On the other hand, quasi-dimensional simulations, which provide a limited description of the in-cylinder processes, are computationally inexpensive.

Autoignition correlations are widely used to predict knock in internal combustion engines as opposed to detailed kinetics mechanisms involving hundreds of reactions due to computational cost. Several autoignition correlations exist in the literature for different fuels, and their functional form depends on the operating parameters like fuel type and temperature range, among other things. In the literature different types of correlations are proposed for gasoline fuel, but to the best of the authors’ knowledge none of these correlations can be used for gasoline-ethanol blends with varying levels of ethanol percentage and a wide range of equivalence ratios and temperatures. In this paper, a new empirical correlation is developed to predict the autoignition of gasoline-ethanol blends over a wide range of temperatures including Negative Temperature Coefficient (NTC) region.

An S.I. combustion model has been developed for application in phenomenological engine simulations. The model is based on a turbulent flame concept, linked to an in-cylinder flow and turbulence calculation. The flame front is assumed to spread from the spark plug and propagate through the cylinder, while interacting with the combustion chamber geometry. The model predictions were compared to combustion rate measurements made in a single cylinder four valve passenger car engine. The data spanned a wide range of operating conditions, from an idle timing sweep, to part load EGR and mixture ratio sweeps, to a wide open throttle speed sweep. The results of the comparisons showed a generally good agreement. Some difficulties were encountered at idle, where cycle-to-cycle variability makes modeling difficult especially at early timing settings.

A combustion bomb has been developed which allows simulation of diesel combustion without the need to heat the bomb to high temperatures. Simulation of the compression stroke is achieved by burning a lean precharge composed of acetylene, oxygen and nitrogen. By controlling the initial partial pressures of these constituents it is possible to burn them to a state with an oxygen concentration, temperature and pressure representative of conditions in a diesel engine at the start of fuel injection. Diesel fuel injected into these gases autoignites and burns in a manner typical of combustion in diesel engines. This paper describes the design and operation of such a bomb. Experimental results are presented to illustrate its salient features. Particular attention is devoted to various means of obtaining optical access to the flow and the advantages offered over rapid compression machines or heated bombs.

An increasing emphasis is being placed in the vehicle development process on transient operation of engines and vehicles, and of engine/vehicle integration, because of their importance to fuel economy and emissions. Simulations play a large role in this process, complementing the more usual test-oriented hardware development process. This has fueled the development and continued evolution of advanced engine and powertrain simulation tools which can be utilized for this purpose. This paper describes a new tool developed for applications to transient engine and powertrain design and optimization. It contains a detailed engine simulation, specifically focused on transient engine processes, which includes detailed models of engine breathing (with turbocharging), combustion, emissions and thermal warm-up of components. Further, it contains a powertrain and vehicle dynamic simulation.

Numerical simulation of in-cylinder processes can significantly reduce the development and refinement costs of engines. While it can be argued that higher fidelity models improve accuracy of prediction, it comes at the expense of high computational cost. In this respect, a 3D analysis of in-cylinder processes may not be feasible for evaluating large number of design and operating conditions. The situation can be more foreboding for transient simulations. In the current work a phenomenological combustion modeling approach is explored that can be implemented in a lower fidelity modeling framework and can approach the accuracy of higher dimensional models with significant reduction in computational cost. The proposed model uses transported probability density function (tPDF) method within a 0D framework to provide a computationally efficient solution while capturing the essential physics of in-cylinder combustion.