Search Results

This paper describes the development of a computational thermodynamic model of compression, combustion and expansion processes of gasohol, ethanol and Natural Gas (NG) for the cylinder pressure curve prediction of a Flexible Fuel engine, working with a NG kit installed. The combustion process is modeled using a Wiebe function. Equations for specific heat at constant pressure (Cp) were developed for each fuel for temperatures up to 4000 K. The model output generates the cylinder gas pressure and temperature, work output and heat release profiles as functions of crank angle, allowing studies of engine performance parameters in different working conditions for each fuel. The differences between the experimental and simulation results were lower than 4% for the maximum cylinder pressure value.

Brazil is known for its long experience on using alternative fuels, mainly ethanol for light duty vehicles. In 2002, it was released the Flexible fuel car that can run with gasohol (gasoline with 22% of ethanol), hydrated ethanol or any blend of these fuels. By the end of 2006, national production of these vehicles represented around 80% of the total. Brazil is also the second world fleet of Natural Gas Vehicles (NGV), with more than 1,4 million light duty converted vehicles. This paper describes the development of a computational thermodynamic model of compression, combustion and expansion processes of gasohol, ethanol and Natural Gas (NG) for the cylinder pressure curve prediction of a Flexible Fuel engine, working with a NG kit installed. The combustion process is modeled using a Wiebe function, which establishes the mass fraction of burned fuel. Convective heat transfer to cylinder walls is estimated with an empirical correlation for heat transfer coefficient determination.

An experimental investigation was performed on an engine dynamometer to study in cylinder pressure curve and combustion parameters variability with ethanol addition. It was used a Flex-Fuel engine, 1.4 L, 4 cylinders, with a programmable engine control unit to optimize the calibration for different blends of Brazilian gasoline and hydrous ethanol. Engine was calibrated for maximum break torque limited by knocking. In-cylinder pressure was measured by using a pressure sensor installed on the spark plug and analyzed by a combustion data system. Combustion duration, mass fraction burned, indicated mean effective pressure (IMEP) and others were calculated based on in-cylinder pressure curve data. The combustion variability was analyzed from 300 recorded engine cycle for each operating condition. Results for some operating conditions indicated that ethanol addition can reduce combustion variability on a non linear pattern.

Nowadays computer simulation is an important tool to support new internal combustion engine projects, but still further studies are necessary for its use in fuel development. In order to study the influence of fuel properties on engine combustion and emission performance, a computer model was designed based on a Flex-Fuel engine geometric data. Model was validated with experimental tests done on an engine dynamometer. A simulation software was used to simulate the experimental conditions, by using Wiebe two zone combustion and Woschni heat transfer models. In-cylinder maximum pressure, IMEP and emission data were calculated for different gasoline-hydrous ethanol blends at 3875 rpm, 60 Nm and 105 Nm. Total hydrocarbons concentration was simulated comparing the experimental data of hydrocarbons added with unburned ethanol emission measured with a FTIR analyzer.

The automotive industry usually adopts the crankshaft angle between 8° and 10° after piston top dead center for the CA50 (crank angle of 50% of mass fraction burned) in order to set the maximum break torque spark timing calibration in Otto cycle engines. There are few studies of the influence of fuel composition, such as the ethanol content, on the CA50 at the maximum torque operating condition. The subject is relevant to the extent that the fuels used in the Brazilian domestic market are different from those usually adopted abroad. The Brazilian gasoline must contain, by law, a volumetric percentage between 18% and 27% of anhydrous ethanol in its composition and, currently, this level is set at 27%. The introduction of flex fuel vehicles in the domestic market in 2003, which now represent most of the new vehicles production in the Country, allowed the use of any blend of national gasoline and hydrous ethanol. This significantly expanded the range of fuel properties variation.

Combustion Modeling of Internal combustion engines is still a complex matter, requiring further developments to better simulate the performance and emissions of different fuels. In order to study the influence of gasoline-ethanol blends on a Flex-Fuel engine, a computer model was designed to simulate the experimental conditions using Fractal combustion and Woschni based heat transfer models. The simulations were validated with engine dynamometer experimental tests. In-cylinder maximum pressure, IMEP and emissions data were calculated for different gasoline-hydrous ethanol blends at different engine conditions. The computer model presented a predictive behavior and a good agreement with experimental data for in-cylinder maximum pressure and IMEP. Regarding emissions, the simulations of some pollutants could not match precisely the experimental data, showing the need for additional combustion modeling improvements.

Hydrogen is considered one of the cleanest solutions for sustainable mobility. This paper presents an overview of some of these applications, such as internal combustion engines, fuel cell application and also blends of hydrogen and natural gas. This paper addresses questions regarding hydrogen properties such as net heating value, flame speed, power density, range of flammability and ignition energy. Also, the paper will draw a comparison between H2 and fossil and biofuels, such as ethanol. Questions regarding storage conditions, emissions levels, Internal Combustion Engine (ICE) air/fuel ratio among others are expected to be covered as well.