Search Results

The present study aims to obtain a strategy for optimizing the combination of injection conditions and combustion chamber geometry to achieve low carbon monoxide (CO), nitrogen oxides (NOx) and smoke emissions with high thermal efficiency at low loads in direct-injection premixed charge compression ignition (DI-PCCI) operation in a diesel engine. To this end, experiments were performed using a naturally-aspirated single-cylinder DI diesel engine equipped with a common-rail injection system and a cooled exhaust gas recirculation (EGR) system under various injection conditions, including injection timing, injection angle and injection quantity, and combustion chamber geometry. The results indicate that CO emission was reduced at injection timings that provide high peak heat release rates. To improve the NOx-CO trade-off relation, the spray angle should be properly selected depending on the combustion chamber geometry.

The objective of the present study is to elucidate the combustion process of partial premixed charge compression ignition (PCCI) combustion using multiple injections in diesel engines. The effects of the ratio of the quantity of fuel used in the first and second injections, and the injection dwell time on heat release rate, soot and nitrogen oxide (NOx) formations are investigated in simulated partial PCCI combustion using a constant-volume vessel. N-heptane is used as fuel. The experiments are carried out under an ambient condition of 2 MPa and 900 K, which simulates a PCCI-like heat release rate with long ignition delays. The oxygen concentration is set to 21 and 15% to simulate conditions without and with exhaust-gas recirculation (EGR), respectively. The fuel quantity in the first injection is varied between 10 to 40% of the total fuel quantity, and the injection dwell is varied between 0.5 to 2.0 ms.

The objective of this study is to obtain a strategy for adapting injection and exhaust gas recirculation (EGR) conditions to various engine speeds. An experimental study was conducted using a single-cylinder test engine and varying the injection timings of two-stage injection, the injection-quantity ratio, the EGR rate, and the swirl ratio at low (1300 rpm) and high (2300 rpm) engine speeds. When using base injection conditions, the results indicated that problems occurred for the high maximum pressure rise rate at low engine speed and the low thermal efficiency at high engine speed. At low engine speed, retarding the injection timings and increasing the first-injection quantity ratio reduced the maximum pressure rise rate without sacrificing engine performance. At high engine speed, advancing the injection timings improved the thermal efficiency but increased smoke emission.

The aim of this study is to find strategies for fully utilizing the advantage of diesel-ethanol blend fuel in recent diesel engines. For this purpose, experiments were performed using a single-cylinder direct injection diesel engine equipped with a high-pressure common rail injection and a cold EGR system. The results indicate that significant PM reduction at high engine loads can be achieved using 15% ethanol-diesel blend fuel. Increasing injection pressure promotes PM reduction. However, poor ignitability of ethanol blended fuel results in higher rate of pressure rise at high engine loads and unstable and incomplete combustion at lower engine loads. Using pilot injection with proper amount and timing solves above problems. NOx increase due to the high injection pressure can be controlled employing cold EGR. Weak sooting tendency of ethanol-blend fuel enables to use high EGR rates for significant NOx reduction.

The Premixed Charge Compression Ignition (PCCI) natural-gas engine has been investigated extensively as a power source for stationary applications due to its potential for high thermal efficiency and very low NOx emissions. However, methane, which is a major component of natural gas, has a high auto-ignition temperature. Stable ignition of natural gas in PCCI engines can be achieved by high compression ratio, intake air heating, internal EGR and various other techniques. Although each of the above-mentioned methods shows positive effects, to some extent, on engine performance and emissions, the literature indicates that stable operation of the PCCI natural gas engine would require a combination of various techniques, which reveals the need for further investigation. The goal of the present study is to control the PCCI natural gas ignition and combustion by ozone addition into the intake air.

Aim of this study is to clarify the NOx formation mechanism in diesel combustion under high-supercharged condition. Effects of ambient conditions and fuel injection parameters on diesel combustion were investigated using a constant volume chamber. NOx formation process was investigated using a total gas-sampling device. The results indicate that by using the above experimental setup it is possible to realize entirely diffusion combustion like what seen in the highly supercharged condition. Increasing ambient pressure up to 8MPa with high injection pressure shortens the ignition delay and offers a heat release rate proportional to the fuel injection rate with a short combustion duration. Increasing ambient pressure gives a higher NOx formation rate and final NOx concentration. This is due to enhancement in the fuel-air mixing which promotes the heat release.