Search Results

Homogenous Charge Compression Ignition (HCCI) engines offer a good potential for achieving high fuel efficiency while virtually eliminating NOx and soot emissions from the exhaust. However, realizing the full fuel economy potential at the vehicle level depends on the size of the HCCI operating range. The usable HCCI range is determined by the knock limit on the upper end and the misfire limit at the lower end. Previously proven high sensitivity of the HCCI process to thermal conditions leads to a hypothesis that combustion chamber deposits (CCD) could directly affect HCCI combustion, and that insight about this effect can be helpful in expanding the low-load limit. A combustion chamber conditioning process was carried out in a single-cylinder gasoline-fueled engine with exhaust re-breathing to study CCD formation rates and their effect on combustion. Burn rates accelerated significantly over the forty hours of running under typical HCCI operating conditions.

Extending the operating range of the gasoline HCCI engine is essential for achieving desired fuel economy improvements at the vehicle level, and it requires deep understanding of the thermal conditions in the cylinder. Combustion chamber deposits (CCD) have been previously shown to have direct impact on near-wall phenomena and burn rates in the HCCI engine. Hence, the objectives of this work are to characterize thermal properties of deposits in a gasoline HCCI engine and provide foundation for understanding the nature of their impact on autoignition and combustion. The investigation was performed using a single-cylinder engine with re-induction of exhaust instrumented with fast-response thermocouples on the piston top and the cylinder head surface. The measured instantaneous temperature profiles changed as the deposits grew on top of the hot-junctions.

Homogeneous Charge Compression Ignition (HCCI) combustion is known for its significant fuel economy benefit with near-zero NOx and particulate emissions. Stable HCCI combustion relies on a well-controlled temperature and composition of the cylinder charge at the intake valve closing that in turn requires a precise coordination of all engine inputs. In this paper, the HCCI combustion is realized by retaining hot residual from the previous combustion event using the recompression valve strategy. The recompression valve strategy closes the exhaust valves before the top dead center and opens the intake valves at an angle symmetric to the exhaust valve closing. Depending on the engine load, different valve open/close timings with respect to the crank position are used to trap different amounts of residual gases. It is critical to coordinate the change in the valve open/close timings with the change in the injected fuel quantity during load transients in order to maintain stable combustion.

An existing multidimensional in-cylinder flow code, KIVA, was modified to conduct port-and-cylinder gas flow, fuel spray, and combustion calculations in a port-fuel-injection engine. The effect of a moving valve with a stem was modeled using a novel internal obstacle technique in which the valve was represented by a group of discrete computational particles. Previously developed spray and combustion models were used to simulate fuel injection and combustion processes for a solid-cone shaped, pressure-atomized spray with isooctane as the fuel. The spray model was further modified to handle interactions between the spray drops and the valve. The model was applied to a generic port-fuel-injection engine with variations in port orientation, spray cone angle, and valve configuration (without and with a 180-degree shroud).

Increasing the injection pressure in DISI engine is an efficient way to obtain finer droplets but it will also potentially cause spray impingement on the cylinder wall and piston. Consequently, the fuel film sticking on the wall can dramatically increase the soot emission of the engine especially in a cold start condition. On the other hand, ethanol is widely used as an alternative fuel in DI engine due to its sustainable nature and high octane number. In this study, the fuel film characteristics of single-plume ethanol impinging spray was investigated. The experiments were performed under ultra-low fuel/plate temperature to simulate the cold start condition in cold areas. A low temperature thermostatic bath combined with specially designed heat exchangers were used to achieve ultra-low temperature for both the impinging plate and the fuel. Laser induced fluorescence (LIF) technique was employed to measure the thickness of fuel film deposited on the impinging plate.

The comprehensive engine simulation code, WAVE, is extended to include a knock sub-model. A hydrocarbon autoignition model based on a degenerate chain-branching mechanism that constitutes the basic kinetic framework was modified and coupled with WAVE's engine thermodynamic environment for this purpose. Making use of this modified hydrocarbon autoignition model and the flow based in-cylinder heat transfer model in WAVE, the original rapid compression machine (RCM) experiments of Shell can be reproduced reasonably well. In addition, a spatially and temporally resolved end-gas thermodynamic model was developed to allow a more accurate calculation of the end-gas temperature over the combustion chamber wall. The developed end-gas thermodynamic-driven knock model further assumes the existence of a pseudo-boundary-layer temperature profile which is linearly distributed between the unburned end-gas and the wall.

A quasi-steady gas-jet model was applied to examine the spray penetration and deflection in swirling flow during the ignition-delay period in an open-chamber diesel engine timed to start combustion at top dead center. The input to the gas-jet model included measured values of ignition delay and mean fuel-injection velocity. Attempts were made to correlate measured fuel-consumption and soot-emissions data with mixing parameters based on calculated spray penetration and deflection. The engine parameters examined were piston-bowl geometry, compression ratio, speed, and overall air-fuel ratio. Four empirical correlations proposed in the literature were examined. The correlations, which were based on spray penetration and deflection in the swirl direction, represented overall degrees of fuel distribution in the combustion chamber and of utilization of the cylinder air.