Search Results

A multi-zone model was used to predict the operating range of homogeneous charge compression ignition (HCCI) engine, the boundaries of the operating range were determined by knock (presented by ringing intensity), partial burn (presented by combustion efficiency) and cycle-to-cycle variations (presented by the sensitivity of indicated mean effective pressure to the initial temperature). A HCCI engine fueled with iso-octane was simulated, and it was found that the knock and cycle-to-cycle variations predicted by this model showed a satisfactory agreement with measurements under different initial temperatures and equivalence ratios, and the operating range was well reproduced by the model. Furthermore, the model was applied to develop the operating range for different engine speeds by changing initial temperature and equivalence ratio. Finally, the potential to expand the operating range of HCCI engines through two strategies, i.e. variable compression ratio and boost, were investigated.

A 3-D DNS (Three-Dimensional Direct Numerical Simulation) study with detailed chemical kinetic mechanism of methane has been performed to investigate the characteristics of turbulent premixed oxy-fuel combustion in the condition relevant to Spark Ignition (SI) engines. First, 1-D (one-dimensional) laminar freely propagating premixed flame is examined to show a consistent combustion temperature for different dilution cases, such that 73% H2O and 66% CO2 dilution ratios are adopted in the following 3-D DNS cases. Four 3-D DNS cases with various turbulence intensities are conducted. It is found that dilution agents can reduce the overall flame temperature but with an enhancement of density weighted flame speed. CO2 dilution case shows the lowest flame speed both in turbulent and laminar cases.

Owing to the potentials for low NOx and soot emissions, diesel PCCI combustion has been widely studied over last 10 years. However, its control is still the main barrier to constrain it to be applied on production engines. As there are a number of variables which affect the mixing and combustion process, it is difficult to develop control strategies with adequate functions but simple control order for implementing them. In the current research, a reformed Homogeneity Factor (HF) of in-cylinder charge has been explored as a control medium for simplifying the control model structure. Based on multi-pulse injection, the effects of operating parameters on the Homogeneity Factor and the relationship between Homogeneity Factor and mixing, combustion processes, emissions were investigated in a four-valve, direct-injection diesel engine by CFD simulation using KIVA-3V code coupled with detailed chemistry.

Effects of included spray angle with different injection strategies on combustion characteristics, performance and amount of pollutant emission have been computationally investigated in a common rail heavy-duty DI diesel engine. The CFD model was firstly validated with experimental data achieved from a Caterpillar 3401 diesel engine for a conventional part load condition at 1600 rev/min. Three different included spray angles (α = 145°, 105°, 90°) were studied in comparison with the traditional spray injection angle (α = 125°). The results show that spray targeting is very effective for controlling the in-cylinder mixture distributions especially when it accompanied with various injection strategies. It was found that 105° spray cone angle along with an optimized split pre- and post-Top Dead Center (TDC) injection strategy could significantly reduce NOx and soot emissions without much penalty of the fuel consumption, as compared to the wide spray angle.

The mechanism of NOx and soot reduction using different pilot and multiple injection strategies has been computationally studied in a heavy duty DI Diesel engine. A designed set of advanced injection schemes with various variables and exhaust gas recirculation rate (up to 10%) have been analyzed. The CFD model was firstly calibrated against experimental data for a part load operation at 1600 rpm. The computational models used were found to predict the correct trends obtained in the experiment. The study demonstrated the potential and explained the mechanism of the combination of EGR and multiple injection to reduce both soot and NOx emissions together with improved fuel economy.

Droplet velocities in a diesel fuel spray before and after impinging on a wall as well as air movement around the spray are measured at room temperature and pressure. The range of fuel injection pressure is from 101 MPa to 139 MPa. The diagnostic equipment is a Laser Doppler Velocimetry with Burst Spectrum Analyzer (LDV-BSA).The results show that the droplet velocities of such a high pressure diesel fuel spray spread in a wide range (about 0-250m/s), so it is necessary to use the ensemble average for describing the velocity variation with time and space. After injection, the velocity reaches its peak value rapidly then attenuates gradually. When the spray impinges on the wall, the average velocity of the rebounded droplets is obviously reduced and the rebounded angle of most droplets is smaller than 30 degree when the incident angle is 70 degree. In the near field zone, the air entrainment in spray jet appears to be lower than that in gaseous one.

Using a Laser Doppler Velocimetry with Burst Spectrum Analyzer (LDV-BSA), droplet velocities of a diesel fuel spray under a pressure higher than 100 MPa were measured at different points within the spray profile. Results show that although the mean velocity distribution at the sampling plane is rather uniform, the number-based droplet velocity distributions of two sampling points at the same plane are different. The conclusions agree with theoretical predictions through maximum entropy principle qualitatively.

As the impacts of global warming have become increasingly severe, Oxy-Fuel Combustion (OFC) has been widely considered as a promising solution to reduce Carbon Dioxide (CO2) for achieving net-zero emissions. In this study, a one-dimensional simulation was carried out to study the implementation of OFC technology on a practical turbocharged 4-cylinder Gasoline Direct Injection (GDI) engine with economical oxygen-fuel ratios and commercial gasoline. When the engine is converted from Conventional Air-fuel Combustion (CAC) mode to OFC mode, and the throttle opening, oxygen mass fraction, stoichiometric air-fuel ratio (lambda = 1) are kept constant, it was demonstrated that compared to CAC mode, θF gets a remarkable extension whereas θC is hardly affected. θF and θC are very sensitive to the ignition timing, and Brake Specific Fuel Consumption (BSFC) would benefit significantly from applying Maximum Brake Torque (MBT) ignition timing.

Diesel homogeneous charge compression ignition (HCCI) engines with early injection can result in significant spray/wall impingement which seriously affects the fuel efficiency and emissions. In this paper, the spray/wall interaction models which are available in the literatures are reviewed, and the characteristics of modeling including spray impingement regime, splash threshold, mass fraction, size and velocity of the second droplets are summarized. Then three well developed spray/wall interaction models, O'Rourke and Amsden (OA) model, Bai and Gosman (BG) model and Han, Xu and Trigui (HXT) model, are implemented into KIVA-3V code, and validated by the experimental data from recent literatures under the conditions related to diesel HCCI engines. By comparing the spray pattern, droplet mass, size and velocity after the impingement, the thickness of the wall film and vapor distribution with the experimental data, the performance of these three models are evaluated.