Search Results

This paper reports on the fourth part of a continued study on further research and development with the automated Ignition Quality Tester (IQT™). Research over the past six years (reported in SAE papers #961182, 971636 and 1999-01-3591) has demonstrated the capabilities of this automated apparatus to measure the ignition quality and accurately determine a derived cetane number (DCN) for a wide range of middle distillate and non-conventional diesel fuels. The present paper reports on a number of separate investigations supporting these continued studies.

Twelve different hole shapes for diesel injector tips were characterized with DF-2 diesel fuel for spray cone angle over a range of injection pressures from 21 MPa (3 kpsi) to 69 MPa (10 kpsi). A baseline and two of the most radical designs were also tested for drop-size distribution and liquid volume fraction (liquid fuel-air ratio) over a range of pressures from 41 MPa (6 kpsi) to 103 MPa (15 kpsi). All hole shapes were circular in cross-section with minimum diameters of 0.4 mm (0.016 in.), and included converging and diverging hole shapes. Overall hole lengths were constant at 2.5 mm (0.098 in.), for an L/d of 6.2. However, the effective L/d may have been less for some of the convergent and divergent shapes.

This paper explores the possibility of on-board fuel classification for fuel property adaptive compression-ignition engine control system. The fuel classifier is designed to on-board classify the fuel that a diesel engine is running, including alternative and renewable fuels such as bio-diesel. Based on this classification, the key fuel properties are provided to the engine control system for optimal control of in-cylinder combustion and exhaust treatment system management with respect to the fuel. The fuel classifier employs engine input-output response characteristics measured from standard engine sensors to classify the fuel. For proof-of-concept purposes, engine input-output responses were measured for three different fuels at three different engine operating conditions. Two neural-network-based fuel classifiers were developed for different classification scenarios. Of the three engine operating conditions tested, two conditions were selected for the fuel classifier to be active.

Four different vegetable oils, degummed soybean, once refined cottonseed, peanut and sunflower oils, were injected into a high-pressure, high-temperature environment of nitrogen. The environment was controlled to resemble, thermodynamically, conditions present in a diesel engine at the time of fuel injection. Samples were removed from the sprays of these oils while they were being injected. A sonic, water-cooled probe and a cold trap were used to collect the samples. Chemical analyses of the samples indicated that significant chemical changes occur in the oils during the injection process. The major change is the formation of low-molecular weight compounds from the C18:2 and C18:3 fatty acids.

High-speed movie films, and laser-diffraction drop sizing were used to evaluate the structure, penetration rate, cone angle, and drop size distribution of diesel sprays in a constant volume pressure vessel. As further means of evaluating the data, comparisons are made between the film measurements, and calculations from a dense gas jet model. In addition to the high-speed film data that describes the overall structure of the spray as a function of time, a laser diffraction instrument was used to measure drop size distribution through a cross-section of the spray. In terms of the growth of the total spray volume (a rough measure of the amount of air entrained in the spray), spray impingement causes an initial delay, but generally the same overall growth rate as an equivalent unimpeded spray. Agreement between measurements and calculations is excellent for a diesel spray with a 0.15 mm D orifice and relatively high injection pressures.

Because of its dominant role in diesel engine performance and emissions, the fuel injection process has become an area of very active research and development. It is now clear that location, shape, rate of development, and mass flow distribution within each fuel jet are all important in controlling fuel air mixing, wall interactions, combustion rate, and the resulting levels of emissions. The objective of this project was to develop an instrument for measurement of the instantaneous fuel mass and momentum distribution in the jets issuing from diesel injection nozzles. The goal was to develop an instrument concept that can be used in the laboratory for fundamental measurements, as well as a quality control system for use in manufacture of the injection nozzles. The concept of the instrument is based on the measurement of the instantaneous momentum of the fuel jet as it impacts on a surface equipped with pressure sensitive elements.

A combustion-based analytical method, initially developed by the Southwest Research Institute (SwRI) referred to as the Constant Volume Combustion Apparatus (CVCA), has been further researched/developed by an SwRI licensee (Advanced Engine Technology Ltd.) as an Ignition Quality Tester (IQT) for laboratories and refineries. The IQT software/hardware system permits rapid and precise determination of ignition quality for middle distillate fuels. Its features, such as low fuel volume requirement, complete test automation, and self-diagnosis, make it highly suitable for commercial oil industry and research applications. Operating and test conditions were examined in the context of providing a high correlation with cetane number (CN), as determined by the ASTM D-613 method. Preliminary investigation indicates that the IQT results are highly repeatable (± 0.30 CN), providing a high sensitivity to CN variation over the 33 to 58 CN range.

A combustion-based analytical method, initially developed by the Southwest Research Institute (SwRI) and referred to as the Constant Volume Combustion Apparatus (CVCA), has been further researched/developed by an SwRI licensee (Advanced Engine Technology Ltd.). This R&D has resulted in a diesel fuel Ignition Quality Tester (IQT) that permits rapid and precise determination of the ignition quality of middle distillate and alternative fuels. Its features, such as low fuel volume requirement, complete test automation, and self-diagnosis, make it highly suitable for commercial oil industry and research applications. A preliminary investigation, reported in SAE paper 961182, has shown that the IQT results are highly correlated to the ASTM D-613 cetane number (CN). The objective of this paper is to report on efforts to further refine the original CN model and report on improvements to the IQT fuel injection system.

It is now a fairly well established fact that excessive ring and cylinder bore wear can result from the operation of an S. I. engine on neat methanol. The mechanism leading to the excessive wear were investigated using both engine and bench tests. Engine tests using prevaporized superheated methanol indicated that the wear results from reactions between the combustion products and the cast iron cylinder liner, where the presence of liquid methanol in the combustion chamber appears to be an important part of the mechanism. These reactions were investigated using a spinning disc combustor. The spinning disc combustor was used to provide a source of burning methanol droplets which were subsequently quenched on a water-cooled cast iron surface. The condensate formed on the cast iron surface was collected and analyzed for chemical composition. Infrared analysis indicated the presence of large quantities of iron formate, a reaction product of iron and formic acid.

AN INVESTIGATION OF THE EFFECTS of methanol fuel on spark ignition engine wear and deposits is being conducted using a Ford 2.3-liter engine and a modified ASTM sequence V-D test procedure. This testing indicates that at the low temperature conditions of this procedure, methanol reduces the buildup of engine deposits but greatly increases the engine wear rate. Various experiments to identify the wear mechanisms were conducted in a CLR single-cylinder engine and are reported here.

A constant volume bomb was used to determine basic combustion characteristics of isooctane, n-heptane, methanol, propane and methane. Results show that the laminar flame velocity of a quiescent homogeneous air/fuel mixture can be derived from pressure-time data in the bomb. The effects of pressure, temperature, and charge dilution on flame velocity and ignition are presented. A thermo-chemical kinetic model accurately predicted concentrations of nitric oxide during combustion and in the burned gas.

As a part of an overall project to improve the techniques for rating the ignition quality of diesel engine fuels, the experiments described in this paper involve examination of the relationship between cetane number and both the physical and chemical ignition delay times. The ignition delay times have been determined from accurate pressure histories obtained during the injection and ignition of a variety of test fuels in a constant volume combustion bomb using a quiescent, high-temperature, high-pressure air environment. The test fuels have included blends of the primary reference fuels as well as other fuels selected because of specific physical properties or chemical composition. The correlation between the cetane numbers of the fuels and various ignition delay times are examined.

Changing fuel quality, increasingly stringent exhaust emission standards, demands for higher efficiency, and the trend towards higher specific output, all contribute to the need for a better understanding of the ignition process in diesel engines. In addition to the impact on the combustion process and the resulting performance and emissions, the ignition process controls the startability of the engine, which, in turn, governs the required compressions ratio and several of the other engine design parameters. The importance of the ignition process is reflected in the fact that the only combustion property that is specified for diesel fuel is the ignition delay time as indicated by the cetane number. The objective of the work described in this paper was to determine the relationship between the ignition process as it occurs in an actual engine, to ignition in a constant volume combustion bomb.

Four major coal fuel projects which were performed at Southwest Research Institute over the past ten years are reviewed. Beginning with the “Alternative Fuels for Highway Utilization” project in 1979, and the success of carbon-black/diesel fuel slurries, the development of the coal slurries is traced to the current technology. Most recently, full-scale locomotive engines have been operated on 50% coal in water slurries at thermal efficiencies approaching that of diesel fuel performance. The paper is concluded with a recommended engine design for coal slurries.

One of the major problems created by the use of methanol fuels in SI engines is the high cylinder bore and ring wear rates observed during operation at low engine temperatures. The objective of the work reported in this paper was to identify the processes controlling the corrosion/wear mechanism in methanol-fueled, spark-ignition engines. Basically, three different types of experiments were performed during this project. The experiments consisted of: 1. Combustion experiments designed to identify the combustion products of methanol at various locations within a confined methanol flame; 2. Exposure studies designed to define the specific role of each of the combustion products on the corrosion mechanism; 3. Lubricant screening experiments designed to identify the mode of penetration of the oil film, and the location, in the microscale, of the surface attack. Performic acid was identified as the corrosive agent.

The ignition delay times of forty-two different fuels were measured in a constant volume combustion bomb. The measurements were performed at three different initial air temperatures using fuels ranging from the primary reference fuels for cetane rating to complex mixtures of coal-derived liquids. The ignition delay times were examined in terms of the classical definitions of the physical and chemical delay times. The previously used definitions were found to be inadequate, and new definitions have been proposed. The total ignition delay times were studied in the context of providing a means for rating the ignition quality of the fuels. Fuel ignition quality rating schemes are discussed, including one based on the current cetane number scale as well as one based on a new scale which includes a measure of the sensitivity of the various fuels to the air temperature.

Several diesel injection systems were selected for evaluating the effects of fuel properties on diesel spray characteristics. Fuel properties that were examined were viscosity and specific gravity. The selected injection systems were operated on nine test fuels covering a broad range of viscosity and specific gravity. High-speed movies were taken of the fuels being injected into a high-pressure environment. Penetration and cone angle data were reduced from the movies and used as a basis for fuel-to-fuel comparisons. In addition, drop size distribution data were obtained for one injection system operating on four fuels with different viscosities. Fuel viscosity was found to have an effect on spray tip penetration. For a pintle-type nozzle as fuel viscosity increased, the tip penetration rate decreased. Tip penetration rate from a pressure time injection system was proportional to the fuel viscosity, in that as viscosity increased, tip penetration increased.

The specific goal of this project was to determine if there is a difference in the lube oil degradation rates in a heavy-duty diesel engine equipped with an EGR system, as compared to the same configuration of the engine, but minus the EGR system. A secondary goal was to develop FTIR analysis of used lube oil as a sensitive technique for rapid evaluation of the degradation properties of lubricants. The test engine selected for this work was a Caterpillar 3176 engine. Two engine configurations were used, a standard 1994 design and a 1994 configuration with EGR designed to meet the 2004 emissions standards. The most significant changes in the lubricant occurred during the first 50-100 hours of operation. The results clearly demonstrated that the use of EGR has a significant impact on the degradation of the engine lubricant.

This paper reports on the third part of a continued study (SAE Papers 961182, 971636) to develop the Ignition Quality Tester (IQT™). Past research has shown that this automated laboratory/refinery apparatus can be used to accurately predict the cetane number of middle distillates and alternative fuels using small sample volumes (< 50 mL). The paper reports on the main objective of a study performed by Advanced Engine Technology Ltd. (AET), in co-operation with its research partners. The primary research objective of this work is to further the understanding of fuel preparation (fuel air mixing) and start of combustion processes in the IQT™. Key to this understanding is the manner in which single molecule compounds and full boiling-range diesel fuels behave during these processes. Insights are provided into the manner in which the American Society for Testing and Materials (ASTM) D-613 primary reference fuels (PRFs) undergo fuel preparation and start of combustion in the IQT™.