Search Results

This study investigated neat n-butanol combustion, emissions and thermal efficiency characteristics in a compression ignition (CI) engine by using two fuelling techniques - port fuel injection (PFI) and direct injection (DI). Diesel fuel was used in this research for reference. The engine tests were conducted on a single-cylinder four-stroke DI diesel engine with a compression ratio of 18.2 : 1. An n-Butanol PFI system was installed to study the combustion characteristics of Homogeneous Charge Compression Ignition (HCCI). A common-rail fuel injection system was used to conduct the DI tests with n-butanol and diesel. 90 MPa injection pressure was used for the DI tests. The engine was run at 1500 rpm. The intake boost pressure, engine load, exhaust gas recirculation (EGR) ratio, and DI timing were independently controlled to investigate the engine performance.

In this work, an active injection control strategy is developed for enabling clean and efficient combustion on an ethanol-diesel dual-fuel engine. The essence of this active injection control is the minimization of the diffusion burning and resultant emissions associated with the diesel injection while maintaining controllability over the ignition and combustion processes. A stand-alone injection bench is employed to characterize the rate of injection for the diesel injection events, and a regression model is established to describe the injection timings and injector delays. A new combustion control parameter is proposed to characterize the extent of diffusion burning on a cycle-to-cycle basis by comparing the modelled rate of diesel injection with the rate of heat release in real time. The test results show that the proposed parameter, compared with the traditional ignition delay, better correlates to the enabling of low NOx and low smoke combustion.

The spark ignition circuit inside an internal combustion engine system is the source which provides the initiation energy required for triggering combustion in a spark ignition (SI) engine in-cylinder air/fuel mixture. Proper spark phasing and adequate spark energy release in spark ignited combustion would yield significant combustion efficiency improvement and affect the in-cylinder production species composition. In this work a simplified spark ignition circuit model constructed based on circuit theorems is proposed. Measurements on how ignition pressure, secondary circuit series resistance and dwell duration would affect the ignition energy migration are presented. Simulations using the proposed model have also demonstrated similar energy migration trends to measurement results which show the influences caused by different secondary series resistance and dwell durations.

An experimental investigation of low temperature combustion (LTC) cycles is conducted with diesel and ethanol fuels on a high compression ratio (18.2:1), common-rail diesel engine. Two LTC modes are studied; near-TDC injection of diesel with up to 60% exhaust gas recirculation (EGR), and port injected ethanol ignited by direct injection of diesel with moderate EGR (30-45%). Indicated mean effective pressures up to 10 bar in the diesel LTC mode and 17.6 bar in the dual-fuel LTC mode have been realized. While the NOx and smoke emissions are significantly reduced, a thermal efficiency penalty is observed from the test results. In this work, the efficiency penalty is attributed to increased HC and CO emissions and a non-conventional heat release pattern. The influence of heat release phasing, duration, and shape, on the indicated performance is explained with the help of parametric engine cycle simulations.

The use of low temperature combustion (LTC) in diesel engines tends to suppress the NOx and dry soot emissions from diesel engines. However, due to the limitations of conventional diesel fuel properties, such as the high reactivity and low volatility, implementation of LTC is highly dependent on the application of exhaust gas recirculation (EGR). While the replacement of some of the fresh air intake with the burnt exhaust gas using EGR prevents premature combustion, it also results in a reduction in thermal efficiency. In this work, the use of two different alcohol fuels, ethanol and butanol, in a high compression ratio diesel engine has been investigated to examine their potential as substitutes for conventional diesel fuel when operating under low temperature combustion mode. The effect of diesel injection timing, alcohol fuel ratios, and EGR on engine emissions and efficiency were studied at indicated mean effective pressures in the range 0.8 to 1.2 MPa.

Experimental testing was done with a modern compression ignition engine to study the effect of the engine load and the effect of different fuels on the post injection characteristics. Two different fuels were utilized; ultra-low sulphur diesel and n-butanol. The results showed that a post injection can be an effective method for increasing the operating range of the engine load. Engine operation at high load can be limited by the peak cylinder pressure but the test results showed that an early post injection can increase the engine load without increasing the peak in-cylinder pressure. Neat butanol combustion may have a very high peak in-cylinder pressure and a very high peak pressure rise rate even at low load conditions. The test results showed that a butanol post injection can contribute to engine power without significantly affecting the peak pressure rise rate and the peak in-cylinder pressure.