Search Results

This paper summarizes the Fast Fourier Transform (FFT) methodology, special equipment, set-up and testing that is recommended to properly characterize the surface of bearing journals that will not result in objectionable noise or vibration. Traditional surface profiles and finish callouts do not capture some of the key characteristics for addressing what is often the customer's greatest complaint, noise. Noise can vary based on the sensitivity of the vehicle but understanding how to accurately describe (design, test, and measure) a surface for a given vehicle can result in an optimized design and reduce process time during manufacturing. Furthermore, this paper will recommend techniques for determining the proper limits of the FFT callouts.

An ignition delay correlation was developed for a toluene reference fuel (TRF) blend that is representative of automotive gasoline fuels exhibiting two-stage ignition. Ignition delay times for the autoignition of a TRF 91 blend with an antiknock index of 91 were predicted through extensive chemical kinetic modeling in CHEMKIN for a constant volume reactor. The development of the correlation involved determining nonlinear least squares curve fits for these ignition delay predictions corresponding to different inlet pressures and temperatures, a number of fuel-air equivalence ratios, and a range of exhaust gas recirculation (EGR) rates. In addition to NO control, EGR is increasingly being utilized for managing combustion phasing in spark ignition (SI) engines to mitigate knock. Therefore, along with other operating parameters, the effects of EGR on autoignition have been incorporated in the correlation to address the need for predicting ignition delay in SI engines operating with EGR.

The double linear damage model developed by Manson and Halford helps to determine the knee point, which is the intersection between the two straight lines. The damage to the component is then calculated based on this knee point. The new approach mentioned in this paper helps to evaluate the damage on the component in a slightly different way. It uses the knee points as mentioned by Manson and Halford and decomposes the damage to the component for Phase I & Phase II. It then uses the equivalent damage approach and establishes the damage to the component. This will be explained with an example.

Three-dimensional transient simulations using KIVA-3V were conducted on a 4-stroke high-compression ratio, methanol-fueled, direct-injection (DI) engine. The engine had two intake ports that were designed to impart a swirling motion to the intake air. In some cases, the intake system was modified, by decreasing the ports diameter in order to increase the swirl ratio. To investigate the effect of adding shrouds to the intake valves on swirl, two sets of intake valves were considered; the first set consisted of conventional valves, and the second set of valves had back shrouds to restrict airflow from the backside of the valves. In addition, the effect of using one or two intake ports on swirl generation was determined by blocking one of the ports.

Numerical simulations of lean Methanol combustion in a four-stroke internal combustion engine were conducted on a high-compression ratio engine. The engine had a removable integral injector ignition source insert that allowed changing the head dome volume, and the location of the spark plug relative to the fuel injector. It had two intake valves and two exhaust ports. The intake ports were designed so the airflow into the engine exhibited no tumble or swirl motions in the cylinder. Three different engine configurations were considered: One configuration had a flat head and piston, and the other two had a hemispherical combustion chamber in the cylinder head and a hemispherical bowl in the piston, with different volumes. The relative equivalence ratio (Lambda), injection timing and ignition timing were varied to determine the operating range for each configuration. Lambda (λ) values from 1.5 to 2.75 were considered.

A numerical study on the combustion of Methanol in a directly injected (DI) engine was conducted. The study considers the effect of the bowl-in-piston (BIP) geometry, swirl ratio (SR), and relative equivalence ratio (λ), on flame propagation and burn rate of Methanol in a 4-stroke engine. Ignition-assist in this engine was accomplished by a spark plug system. Numerical simulations of two different BIP geometries were considered. Combustion characteristics of Methanol under swirl and no-swirl conditions were investigated. In addition, the amount of injected fuel was varied in order to determine the effect of stoichiometry on combustion. Only the compression and expansion strokes were simulated. The results show that fuel-air mixing, combustion, and flame propagation was significantly enhanced when swirl was turned on. This resulted in a higher peak pressure in the cylinder, and more heat loss through the cylinder walls.

Collection of diesel exhaust using the Tapered Element Oscillating Microbalance (TEOM) instrument was investigated as an alternative to the traditional method of filter weighing for particulate matter mass determination. Such an approach, if successful, would eliminate considerable manual labor involved in weighing, as well as the delay of hours or days before final results were known. To avoid known artifacts in the second-by-second mode of operation, the TEOM was used in a phase-by-phase mode and was equilibrated with air of constant temperature and humidity before each measurement. Electrically operated valves were used to automate the equilibration and measurement process. The study also included a comparison between two types of TEOM filter - an older type and a new one designed by the TEOM manufacturer for more uniform flow and less flexing. Best results were obtained with the TEOM using the new filter under no-flow conditions.

Advanced High-Strength Steels (AHSS) have become an essential part of the lightweighting strategy for automotive body structures. The ability to fully realize the benefits of AHSS depends upon the ability to aggressively form, trim, and pierce these steels into challenging parts. Tooling wear has been a roadblock to stamping these materials. Traditional die materials and designs have shown significant problems with accelerated wear, galling and die pickup, and premature wear and breakage of pierce punches. [1] This paper identifies and discusses the tribological factors that contribute to the successful stamping of AHSS. This includes minimizing tool wear and galling/die pick-up; identifying the most effective pierce clearance (wear vs. burr height) when piercing AHSS; and determining optimal die material and coating performance for tooling stamping AHSS.

Scuffing is one of the major problems that influence the life cycle and reliability of several auto components, including engine cylinder kits, flywheels, camshafts, crankshafts, and gears. Ferrous casting materials, such as gray cast iron, ductile cast iron and austempered ductile cast iron (ADI) are widely applied in these components due to their self-lubricating characteristics. The purpose of this research is to determine the scuffing behavior of these three types of cast iron materials and compare them with 1050 steel. Rotational ball-on-disc tests were conducted with white mineral oil as the lubricant under variable sliding speeds and loads. The results indicate that the scuffing initiation is due to either crack propagation or plastic deformation. It is found that ADI exhibits the highest scuffing resistance among these materials.

A high-speed/high-resolution imaging technique and analysis were applied to study fuel injector spray timed evolution in ambient air and in a motored single-cylinder engine. Alcohol fuel was injected from a mid-pressure injection system into the engine cylinder at shaft speed of 1,000 rpm. The fuel injection system with various nozzles was designed for use in the EPA/NVFEL program to develop clean and efficient engines that use alternative fuels. A 15W copper vapor laser with a fiber optic delivery system synchronized with a high-speed drum streak camera was utilized to expose films at 5,000 frames per second (fps). The spray characteristics were investigated at 15.0 MPa injection pressure and injection duration range of 3-5 ms. A sequence of successive frames was selected from the films to examine the influence of the injector parameters and the valve lift on the atomization process. The spray penetration was quantified by analyzing the high-speed films.

The development process of a water pump impeller used on a sport utility vehicle engine is described. A review of the design process is presented in this paper including the computer-aided flow analysis together with testing procedures. By computer modeling, one can estimate the coolant flow characteristics of a given impeller blade shape for providing increased cooling performance and improved efficiency on the engine. It also provides directions for the improved design. The test data are used specifically to confirm the analysis results.

In an effort to improve the dent resistance of exterior body panels at reduced steel thicknesses, some automobile manufacturers have pursued the application of bake hardenable steels. Unfortunately, bake hardenable steels have only been available as cold rolled or with electro-zinc or electro zinc/iron coatings. This situation has been a deterrent for those automobile manufacturers that prefer the use of hot dip galvanneal coatings. Recently, the interest in hot dip galvanneal bake hardenable steels has led to the investigation and development of this more advanced steel grade. This paper presents the results of a stamping trial and dent testing on three exposed hot dip galvannealed materials; i) Regular Ultra Low Carbon (ULC), ii) Rephosphorized ULC, and iii) Rephosphorized Bake Hardenable ULC steel.

Three-dimensional numerical simulations of a diesel-fueled engine with a pre-chamber located in the cylinder head and a bowl in the piston were performed. The study considers the effect of diesel combustion in the pre-chamber on turbulence generation and hence fuel-air mixing and combustion in the piston-bowl. Diesel fuel was injected directly into the pre-chamber and the piston bowl at different times. In order to better determine the effect of pre-chamber combustion on the main chamber combustion, various pre-chamber injection timings were considered. The results show that pre-chamber combustion caused the average cylinder pressure to increase by up to 20% in some cases.

This paper presents a review of the regulatory, environmental, and health issues surrounding the use of halons as a fire suppressant and a summary of the recently completed Racecar Fire Suppressant Exposure Study by ICF Consulting, Inc., under contract with the U.S. Environmental Protection Agency (EPA) (U.S. EPA, 2004a). In 2003 the EPA learned that the SFI Foundation Inc., the organization responsible for developing safety regulations and testing requirements for numerous Performance Racing Industry (PRI) sanctioning bodies, was revising its Quality Assurance Specification for On Board Fire Suppression Systems (SFI Specification 17.1). The previous Specification 17.1 required either halon 1211 or halon 1301 to be used in these systems. Halons are ozone-depleting substances (ODS) widely used in fire protection applications and whose production and use are controlled under the Montreal Protocol and the Clean Air Act (CAA).

This paper presents results from a study of the particle size distributions emitted by a heavy-duty diesel engine equipped with a common-rail fuel injection system. The study focused on two key sampling and engine operating variables: dilution ratio and fuel injection pressure. Results show that the number mean diameter of the particle size distributions decreased with increasing dilution ratios. Also, the total number concentration of particles did not change with different dilution ratios. In addition, it was found that fuel injection pressures affected the size distribution of the particles sampled. Under some engine operating conditions increasing the fuel injection pressure resulted in an increased number of nuclei mode particles.

Today, some vehicles include a regenerative-braking system such as the electrical motor-generator that converts the vehicle's kinetic energy into electrical energy to recharge one or more vehicle batteries. The idea is to use air flow to produce additional electrical energy in response to deceleration of the vehicle. With the Wind Power Generator System (WPGS) as a green system, a vehicle can produce extra energy, reduce gasoline usage, and reduce air pollution.

The paper analyzes energy use and emissions per GJ of various fuels delivered to the vehicle fuel tank, covering extraction, fuel production, transportation, storage, and distribution phases of the life cycle of alternative fuels. Drawing on a number of existing studies, the modeling issues and approaches, main results and insights are summarized. The range of estimates in various studies is large; however, common patterns can be observed. The analysis indicates, that conventional gasoline fuel cycle has robust advantages with respect to energy efficiency, conventional pollutant emissions, and most importantly, existing infrastructure compared to alternative fuels. Fossil fuel based alternatives like CNG, NG–Methanol, NG–FTL do not result in significant improvement in fuel cycle environmental performance. Biofuels offer the benefits of lower and even negative GHG emissions, sustainability, and domestic fuel production.