Search Results

This paper summarizes the Fast Fourier Transform (FFT) methodology, special equipment, set-up and testing that is recommended to properly characterize the surface of bearing journals that will not result in objectionable noise or vibration. Traditional surface profiles and finish callouts do not capture some of the key characteristics for addressing what is often the customer's greatest complaint, noise. Noise can vary based on the sensitivity of the vehicle but understanding how to accurately describe (design, test, and measure) a surface for a given vehicle can result in an optimized design and reduce process time during manufacturing. Furthermore, this paper will recommend techniques for determining the proper limits of the FFT callouts.

An ignition delay correlation was developed for a toluene reference fuel (TRF) blend that is representative of automotive gasoline fuels exhibiting two-stage ignition. Ignition delay times for the autoignition of a TRF 91 blend with an antiknock index of 91 were predicted through extensive chemical kinetic modeling in CHEMKIN for a constant volume reactor. The development of the correlation involved determining nonlinear least squares curve fits for these ignition delay predictions corresponding to different inlet pressures and temperatures, a number of fuel-air equivalence ratios, and a range of exhaust gas recirculation (EGR) rates. In addition to NO control, EGR is increasingly being utilized for managing combustion phasing in spark ignition (SI) engines to mitigate knock. Therefore, along with other operating parameters, the effects of EGR on autoignition have been incorporated in the correlation to address the need for predicting ignition delay in SI engines operating with EGR.

The double linear damage model developed by Manson and Halford helps to determine the knee point, which is the intersection between the two straight lines. The damage to the component is then calculated based on this knee point. The new approach mentioned in this paper helps to evaluate the damage on the component in a slightly different way. It uses the knee points as mentioned by Manson and Halford and decomposes the damage to the component for Phase I & Phase II. It then uses the equivalent damage approach and establishes the damage to the component. This will be explained with an example.

The AUTomotive Open System ARchitecture (AUTOSAR) Development Partnership has published early 2008 the specifications Release 3.0 [1], with a prime focus on the overall architecture, basic software, run time environment, communication stacks and methodology. Heavy developments have taken place in the OEM and supplier community to deliver AUTOSAR loaded cars on the streets starting 2008 [2]. The 2008 achievements have been: Improving the specifications in order to secure the exploitation for body, chassis and powertrain applications Adding major features: safety related functionalities, OBD II and Telematics application interfaces.

The objective of this paper is to explore the influence of freestream turbulence on heat transfer processes to passenger cars in climatic wind tunnels. This will include a consideration of different flow zones on the vehicles. It will be shown up to which value of the turbulence intensity the influence on the heat transfer to the passenger compartment remains insignificant. The effects of freestream turbulence on the design and operation of climatic wind tunnels are discussed. The upper limit for the turbulence intensity can be regarded as a sizing quantity to be used in planning and operating vehicle-climatic wind tunnels in the future.

Advanced High-Strength Steels (AHSS) have become an essential part of the lightweighting strategy for automotive body structures. The ability to fully realize the benefits of AHSS depends upon the ability to aggressively form, trim, and pierce these steels into challenging parts. Tooling wear has been a roadblock to stamping these materials. Traditional die materials and designs have shown significant problems with accelerated wear, galling and die pickup, and premature wear and breakage of pierce punches. [1] This paper identifies and discusses the tribological factors that contribute to the successful stamping of AHSS. This includes minimizing tool wear and galling/die pick-up; identifying the most effective pierce clearance (wear vs. burr height) when piercing AHSS; and determining optimal die material and coating performance for tooling stamping AHSS.

Scuffing is one of the major problems that influence the life cycle and reliability of several auto components, including engine cylinder kits, flywheels, camshafts, crankshafts, and gears. Ferrous casting materials, such as gray cast iron, ductile cast iron and austempered ductile cast iron (ADI) are widely applied in these components due to their self-lubricating characteristics. The purpose of this research is to determine the scuffing behavior of these three types of cast iron materials and compare them with 1050 steel. Rotational ball-on-disc tests were conducted with white mineral oil as the lubricant under variable sliding speeds and loads. The results indicate that the scuffing initiation is due to either crack propagation or plastic deformation. It is found that ADI exhibits the highest scuffing resistance among these materials.

Reduction of nitrogen oxides in Diesel exhaust gas is a challenging task. This paper reports results from an extensive study using Pt-based catalysts involving synthetic gas activity testing (SCAT), engine bench testing and tests on passenger cars. Preliminary SCAT work highlighted the importance of Pt-dispersion, and both SCAT and bench engine testing yielded comparable NOx conversions under steady state conditions at high HC:NOx ratios. On passenger cars in the European cycle without secondary fuel injection NOx conversion was lower than obtained in the steady state tests. Better conversion was obtained in the FTP cycle, where secondary injection was employed. Higher HC:NOx, ratios and more favourable temperature conditions which were present in the exhaust contributed to this higher conversion.

The development process of a water pump impeller used on a sport utility vehicle engine is described. A review of the design process is presented in this paper including the computer-aided flow analysis together with testing procedures. By computer modeling, one can estimate the coolant flow characteristics of a given impeller blade shape for providing increased cooling performance and improved efficiency on the engine. It also provides directions for the improved design. The test data are used specifically to confirm the analysis results.

In an effort to improve the dent resistance of exterior body panels at reduced steel thicknesses, some automobile manufacturers have pursued the application of bake hardenable steels. Unfortunately, bake hardenable steels have only been available as cold rolled or with electro-zinc or electro zinc/iron coatings. This situation has been a deterrent for those automobile manufacturers that prefer the use of hot dip galvanneal coatings. Recently, the interest in hot dip galvanneal bake hardenable steels has led to the investigation and development of this more advanced steel grade. This paper presents the results of a stamping trial and dent testing on three exposed hot dip galvannealed materials; i) Regular Ultra Low Carbon (ULC), ii) Rephosphorized ULC, and iii) Rephosphorized Bake Hardenable ULC steel.

The addition of oxygen-containing components into gasoline exerts a sustained influence on the cold start and warm-up performance of vehicles. The influences are shown on the basis of test results with motor vehicles. The cold start performance of vehicles with an alternative fuel such as methanol is very strongly dependent on the composition of a properly tailored fuel. This fuel should contain light boiling components for the best performance. Results from methanol fuelled vehicles under cold climate conditions are shown here. The warm-up conditions of an 1.3 l-engine starting at -10°C were researched. The additional fuel required under these conditions for heating all the components of the egine including the coolant and lubricant was calculated after the basic measurement of their temperature rise. The additional fuel required due to the higher friction was investigated by motoring the engine.

Volkswagen has built a simulation model of the EA 111 Motors assembly line. It was an important model to study the plant capacity increasing. The study was made in two phases: 500 motors/day and then 1.200motors/day. Using this model, the company could run different scenarios quickly and identify the bottlenecks in the system. So, they could take better decisions in this capacity planning study avoiding future problems in this assembly line.

Diesel exhaust gas contains low molecular aliphatic carbonyl compounds and strongly smelling organic acids, which are known to have an irritant influence on eyes, nose and mucous membranes. Thus, diesel exhaust aftertreatment has to be considered more critically than that of gasoline engines, with respect to the formation of undesired by-products. The results presented here have been carried out as research work sponsored by the German Research Association for Internal Combustion Engines (FVV). The main objective of the three year project was to evaluate the behaviour of current and future catalyst technology on the one hand (oxidation catalyst, CRT system, SCR process), and regulated and certain selected non-regulated exhaust gas emission components and exhaust gas odour on the other hand.

Today, some vehicles include a regenerative-braking system such as the electrical motor-generator that converts the vehicle's kinetic energy into electrical energy to recharge one or more vehicle batteries. The idea is to use air flow to produce additional electrical energy in response to deceleration of the vehicle. With the Wind Power Generator System (WPGS) as a green system, a vehicle can produce extra energy, reduce gasoline usage, and reduce air pollution.