Search Results

The optimization of the air-fuel mixture formation plays a very important role in order to reduce the total amount of emissions from an SI engine. To comply with the EURO5 emission restrictions is necessary to understand the influence of injection timing (with respect to engine load) and injector geometry on the air-fuel dynamic interaction. The aim of this paper is to define a CFD methodology for the simulation of a PFI engine. The goals of this analysis are the evaluation of the injector geometry and injection timing influences on the air-fuel mixture preparation and so on the equivalence ratio distribution inside the combustion chamber. Preliminary assessments of the wall-film and droplet-wall interaction sub models have been carried out in order to validate the methodology [1].

The efficiency of engine operations, i.e. cold start, transient response and operating at idle, depends on the capability of the injection fuel system to promote a homogeneous mixture formation through an efficient interaction with engine fluid dynamics and geometry. The paper presents the development and the application of a methodology for running a CFD PFI engine simulation. A preliminary assessment of the wall-film and droplet-wall interaction sub models has been carried out in order to validate the methodology. Then a three-step numerical procedure has been adopted. The first two steps are aimed to properly initialize the secondary breakup model depending on the type of injector installed on board in order to achieve accurate predictions of spray characteristics.

In the present paper, an analysis of non-evaporating, transient Diesel sprays generated by an automotive common-rail, electronic controlled injection system is described. A standard Diesel fuel and a pure Biodiesel were used for the tests, with sprays evolving in a pressurized test chamber and generated by both cylindrical and conical hole nozzles. The spray analysis is performed mainly by means of a laser sheet technique in order to obtain global spray data suitable for tuning direct injection systems to such fuels and for numerical codes validation. A dispersion analysis among different jets was also performed, along with the injection rate measurement. A PDA system was also used to characterize the behavior of the two fuels with the prototype injector nozzles at ambient conditions.

The injection rate modulation and the spray characteristics are determining factors for the quality of mixture formation when applying GDI. Their variation with load and speed is a basic criterion for the adaptability of a type of injection system to an engine with known requirements. The increased interest for the utilization of regenerative fuels - such as methanol obtained from biomass - as well as the success of previous utilization scenarios of variable gasoline/methanol mixture using manifold injection formed the base of the present analysis: the paper describes the results concerning injection performances and spray characteristics when using gasoline/methanol mixtures with different ratios in a direct injection system with high pressure modulation. The results are compared for different parameters of the injection systems as follows: injection volume, injector opening pressure, needle lift, pintle/seat geometry.

A hybrid model for the atomization of Diesel sprays was developed [1]. The model was added to the KIVA code to better simulate spray evolution. Different implementation for low-medium and high injection pressure sprays are performed. It has already been validated for the low-pressure case [1,2] and in this work it was tested for high injection pressure systems, in a vessel at ambient conditions. It distinguishes between jet primary breakup and droplet secondary breakup. For the latter distinct models are used, as the droplet Weber number changes in the various regimes, in order to take into account the effects of the different relevant forces. For high pressure Diesel spray the effects of jet turbulence, cavitation and nozzle flow on liquid core primary breakup must be considered. Due to the high droplet velocity the catastrophic secondary breakup regime may occur.

This paper describes an experimental bench for a non-intrusive characterization of fuel sprays. The characterization is obtained by computer analysis of the fuel spray images acquired using a high-resolution CCD camera. The bench has been developed by AEA for Siemens Automotive, in collaboration with Siemens' R&D staff and Perugia University researchers. Two different techniques have been implemented to obtain the jet images. The main target of this paper is the comparison of the results obtained using the two different methodologies of analysis.

This paper presents a complete numerical and experimental characterisation of the transient diesel spray of a modern 5-holes high pressure electronic controlled injector performed in a constant volume pressurised vessel. The experimental analysis has been carried out using a self-developed injection rate measuring device, a visualisation rig based on a Nd-Yag pulsed laser and a synchronized CCD camera to measure spray penetration and spray cone angles and a PDA equipment to measure droplets size and velocity. The numerical analysis has been carried out by statically coupling a 1D model of the common rail injection system to a full 3D computation of both gas and fuel spray dynamics. The 1D injection system model has been developed in the AVL HYDSIM environment and the reliability of the model is demonstrated by comparing the numerical results with the experimental data. The multidimensional numerical simulation tool is a modified version of the KIVA-3V code.

The introduction of the high-pressure fully electronic-controlled injection systems has opened a number of new possibilities to optimize diesel engine performance and to reduce pollutant emissions. However greater research efforts are required to meet future European emission legislation. The control of the combustion process, which determines to a large extent the amount of pollutant emissions, requires primarily an understanding of its physics and chemistry as well as the capability to modify one or more of the interdependent process parameters in a given direction. Since many parameters have to be considered, a combined experimental-numerical approach is required.

The control of mixture formation by gasoline direct injection requires the continuous adaptation of the fuel spray characteristics in a broad range of load and speed. This paper presents an experimental analysis of the main spray characteristics for a jet generated by a GDI system with high pressure modulation (Zwickau Ram Tuned). The experimental method is based on spray visualization by a laser sheet technique. The radiation of a Nd-Yag pulsed laser is scattered by the spray droplets laying on the lighted plane and collected by a CCD camera, being fed to a frame grabber. Time and space related structure can be analyzed in any cross section of interest, giving information about jet form and penetration length. In particular, a suitable elaboration (Presence Probability Imaging) of several image series, collected at different delay times after injection start, supplies information about the probability of presence in space of spray liquid fractions.

In the present study, a commercial high pressure, common rail injection system for automotive DI diesel engines was fed with a conventional diesel fuel, a bio-derived fuel and a blend of them. The comparison of spray characteristics was carried out in terms of tip penetration and cone angles; the fuel spray, generated by rail pressures ranging from 60 MPa to 120 MPa, developed in an atmospheric chamber. The experimental set-up is based on a laser sheet technique. The radiation scattered by the spray, generated by a Nd-Yag pulsed laser, is collected by a CCD camera and fed to a frame grabber. A suitably set-up automatic image analysis process allows not only to determine the spray average development in terms of its geometric characteristics, but also to analyse in detail its internal structure. In particular, a suitable elaboration allowed the evaluation of the probability of presence in space of spray liquid fractions.