Search Results

Standard

Transport Area Network Cabling

2007-02-21

HISTORICAL

J2496_200702

This series of SAE Recommended Practices was developed to provide an open architecture system for on-board electronic systems. It is the intention of these documents to allow electronic devices to communicate with each other by providing a standard architecture. This particular document describes the Network Interface and Cabling which defines the requirements needed for communicating between devices that are on different segments of the SAE J2496 Transport Area Network. While these recommended practices may be used in retrofitting older vehicles, the primary intent is for implementation in new bus procurements.

Standard

Powertrain Control Interface for Electronic Controls Used in Medium- and Heavy-Duty Diesel On-Highway Vehicle Applications

2011-08-12

CURRENT

J1922_201108

This SAE Recommended Practice provides a development or possibly interim production communication protocol between engine, transmission, ABS/traction control, and retarder systems until higher speed communication links are established.

Standard

Powertrain Control Interface for Electronic Controls Used in Medium- and Heavy-Duty Diesel On-Highway Vehicle Applications

2008-12-04

HISTORICAL

J1922_200812

This SAE Recommended Practice provides a development or possibly interim production communication protocol between engine, transmission, ABS/traction control, and retarder systems until higher speed communication links are established.

Standard

Powertrain Control Interface for Electronic Controls Used in Medium- and Heavy-Duty Diesel On-Highway Vehicle Applications

2000-09-29

HISTORICAL

J1922_200009

This SAE Recommended Practice provides a development or possibly interim production communication protocol between engine, transmission, ABS/traction control, and retarder systems until higher speed communication links are established.

Standard

OEM/Vendor Interface Specification for Vehicle Electronic Programming Stations

2000-08-28

CURRENT

J1924_200008

The purpose of the SAE Information Report is to address the method of loading vehicle electronic controllers with chassis and customer specific parameters. This specification shall establish an interface definition. The interface definition must be mutually agreeable to truck OEMs and vendors. The purpose of this specification is not to answer the large protocol issues raised by systems such as GM's MAP. SAE Standard In the future, SAE may use this specification as a basis for an OEM/Vendor interface specification standard.

Standard

Vehicle Electronic Programming Stations (VEPS) System Specification for Win32™

2010-02-05

HISTORICAL

J2461_201002

SAE J2461 specifies the recommended practices of a Vehicle Electronics Programming Stations (VEPS) architecture.in a Win32™ environment. This system specification, SAE J2461, was a revision of the requirements for Vehicle Electronics Programming Stations (VEPS) set forth in SAE J2214, Vehicle Electronics Programming Stations (VEPS) System Specification for Programming Components at OEM Assembly Plants (Cancelled Jun 2004). The J2214 standard has been cancelled indicating that it is no longer needed or relevant.

Standard

Vehicle Electronic Programming Stations (VEPS) System Specification for Win32™

2002-08-29

HISTORICAL

J2461_200208

This system specification, SAE J2461, revises the requirements for Vehicle Electronics Programming Stations (VEPS) set forth in SAE J2214, Vehicle Electronics Programming Stations (VEPS) System Specification for Programming Components at OEM Assembly Plants. SAE J2461 specifies the recommended practices for a Win32™ environment while maintaining the core VEPS architecture specified in SAE J2214.

Standard

Vehicle Electronic Programming Stations (VEPS) System Specification for Win32®

2022-11-22

HISTORICAL

J2461_202211

SAE J2461 specifies the recommended practices of a Vehicle Electronics Programming Stations (VEPS) architecture.in a Win32® environment. This system specification, SAE J2461, was a revision of the requirements for Vehicle Electronics Programming Stations (VEPS) set forth in SAE J2214, Vehicle Electronics Programming Stations (VEPS) System Specification for Programming Components at OEM Assembly Plants (Cancelled Jun 2004). The J2214 standard has been cancelled indicating that it is no longer needed or relevant.

Standard

Vehicle Electronic Programming Stations (VEPS) System Specification for Win32®

2013-09-23

HISTORICAL

J2461_201309

SAE J2461 specifies the recommended practices of a Vehicle Electronics Programming Stations (VEPS) architecture.in a Win32® environment. This system specification, SAE J2461, was a revision of the requirements for Vehicle Electronics Programming Stations (VEPS) set forth in SAE J2214, Vehicle Electronics Programming Stations (VEPS) System Specification for Programming Components at OEM Assembly Plants (Cancelled Jun 2004). The J2214 standard has been cancelled indicating that it is no longer needed or relevant.

Standard

VENDOR COMPONENT PROGRAM DATA FILE INTERFACE FOR OEM ASSEMBLY OPERATIONS

1997-02-01

HISTORICAL

J2286_199702

This interface document SAE J2286 revises the requirements for file formats as described in SAE J1924. This document describes Interface 1 (I/F 1) in SAE J2214. This document does not imply the use of a specific hardware interface, but may be used with other hardware interfaces such as SAE J1939. The requirements of SAE J2286 supersede the requirements defined by SAE J1924.

Standard

Power Line Carrier Communications for Commercial Vehicles

2010-12-09

HISTORICAL

J2497_201012

This SAE Recommended Practice defines a method for implementing a bidirectional, serial communications link over the vehicle power supply line among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and software compatibility such as interface requirements, system protocol, and message format that pertain to Power Line Communications (PLC) between Tractors and Trailers. This document defines a method of activating the trailer ABS Indicator Lamp that is located in the tractor.

Standard

Power Line Carrier Communications for Commercial Vehicles

2007-06-21

HISTORICAL

J2497_200706

This SAE Recommended Practice defines a method for implementing a bidirectional, serial communications link over the vehicle power supply line among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and software compatibility such as interface requirements, system protocol, and message format that pertain to Power Line Communications (PLC) between Tractors and Trailers. This document defines a method of activating the trailer ABS Indicator Lamp that is located in the tractor.

Standard

Power Line Carrier Communications for Commercial Vehicles

2023-11-01

CURRENT

J2497_202311

This SAE Recommended Practice defines a method for implementing a bidirectional, serial communications link over the vehicle power supply line among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and software compatibility such as interface requirements, system protocol, and message format that pertain to Power Line Communications (PLC) between Tractors and Trailers. This document defines a method of activating the trailer ABS Indicator Lamp that is located in the tractor.

Standard

Power Line Carrier Communications for Commercial Vehicles

2012-07-30

HISTORICAL

J2497_201207

This SAE Recommended Practice defines a method for implementing a bidirectional, serial communications link over the vehicle power supply line among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and software compatibility such as interface requirements, system protocol, and message format that pertain to Power Line Communications (PLC) between Tractors and Trailers. This document defines a method of activating the trailer ABS Indicator Lamp that is located in the tractor.

Standard

Power Line Carrier Communications for Commercial Vehicles

2002-10-31

HISTORICAL

J2497_200210

This SAE Recommended Practice defines a method for implementing a bidirectional, serial communications link over the vehicle power supply line among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and software compatibility such as interface requirements, system protocol, and message format that pertain to Power Line Communications (PLC) between Tractors and Trailers. This document defines a method of activating the trailer ABS Indicator Lamp that is located in the tractor.

Standard

SERIAL DATA COMMUNICATIONS BETWEEN MICROCOMPUTER SYSTEMS IN HEAVY DUTY VEHICLE APPLICATIONS

1990-10-01

HISTORICAL

J1708_199010

This document defines a recommended practice for implementing a bidirectional, serial communication link among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and basic software compatibility such as interface requirements, system protocol, and message format. The actual data to be transmitted by particular modules, which is an important aspect of communications compatibility, is not specified in this document. These and other details of communication link implementation and use should be specified in the separate application documents referenced in Section 2.

Standard

SERIAL DATA COMMUNICATIONS BETWEEN MICROCOMPUTER SYSTEMS IN HEAVY DUTY VEHICLE APPLICATIONS

1989-11-01

HISTORICAL

J1708_198911

This document defines a recommended practice for implementing a bidirectional, serial communication link among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and basic software compatibility such as interface requirements, system protocol, and message format. The actual data to be transmitted by particular modules, which is an important aspect of communications compatibility, is not specified in this document. These and other details of communication link implementation and use should be specified in the separate application documents referenced in Section 2.

Standard

SERIAL DATA COMMUNICATIONS BETWEEN MICROCOMPUTER SYSTEMS IN HEAVY-DUTY VEHICLE APPLICATIONS

1993-10-19

HISTORICAL

J1708_199310

This SAE Recommended Practice defines a recommended practice for implementing a bidirectional, serial communication link among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and basic software compatibility such as interface requirements, system protocol, and message format. The actual data to be transmitted by particular modules, which is an important aspect of communications compatibility, is not specified in this document. These and other details of communication link implementation and use should be specified in the separate application documents referenced in Section 2.

Standard

Serial Data Communications Between Microcomputer Systems in Heavy-Duty Vehicle Applications

2004-08-25

HISTORICAL

J1708_200408

This SAE Recommended Practice defines a recommended practice for implementing a bidirectional, serial communication link among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and basic software compatibility such as interface requirements, system protocol, and message format. The actual data to be transmitted by particular modules, which is an important aspect of communications compatibility, is not specified in this document. These and other details of communication link implementation and use should be specified in the separate application documents referenced in Section 2.

Standard

Serial Data Communications Between Microcomputer Systems in Heavy-Duty Vehicle Applications

2016-09-13

CURRENT

J1708_201609

This SAE Recommended Practice defines a recommended practice for implementing a bidirectional, serial communication link among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and basic software compatibility such as interface requirements, system protocol, and message format. The actual data to be transmitted by particular modules, which is an important aspect of communications compatibility, is not specified in this document. These and other details of communication link implementation and use should be specified in the separate application documents referenced in Section 2.