Refine Your Search

Date

Date

Topic

Topic

Commercial Vehicle Management and Organizations Human Factors and Ergonomics Environment Truck and Bus Total Vehicle Steering Committee

Search Results

Viewing 1 to 20 of 22
12Next >Last >>
Sort by relevance
Standard

Trailer Axle Alignment
1999-03-24
HISTORICAL
J875_199903
The scope of this SAE Recommended Practice, trailer axle alignment, is to identify the dimensional limits of, and a method to, establish a perpendicular relationship between the king pin centerline and the axle centerline at its midpoint. Various types of equipment are commercially available which can be used for this measurement which provides varying degrees of accuracy, but none can be endorsed by SAE. The most fundamental methods of measurement will be described here, but other equipment is available if a greater degree of accuracy is desired.
Standard

Trailer Axle Alignment
2011-06-13
CURRENT
J875_201106
The scope of this SAE Recommended Practice, trailer axle alignment, is to identify the dimensional limits of, and a method to, establish a perpendicular relationship between the king pin centerline and the axle centerline at its midpoint. Various types of equipment are commercially available which can be used for this measurement which provides varying degrees of accuracy, but none can be endorsed by SAE. The most fundamental methods of measurement will be described here, but other equipment is available if a greater degree of accuracy is desired.
Standard

MOTOR TRUCK CA DIMENSIONS
1990-09-01
HISTORICAL
J691_199009
This SAE Recommended Practice sets forth recommended back of cab to rear axle (CA) dimensional data. It applies to 4- and 6-wheel motor trucks but not necessarily to truck-tractors.
Standard

Recommended Practice for Splash and Spray Evaluation
2002-09-19
HISTORICAL
J2245_200209
This SAE Recommended Practice provides general guidelines for measuring the splash and spray produced by vehicles operating over wet pavements. The guidelines describe both the video digitizing and the laser methods of analysis. The video-digitizing method uses video images and contrast measurements between black and white checkerboards when a spray cloud is superimposed on them as a means of measuring the obscuring spray. The laser method uses laser transmittance through the spray cloud as the means of measurement. It is left to the users of this practice to decide which method is best suited to their needs. There is no implied relationship between these two methods, although it is expected that the ranking of relative spray reduction between test vehicle configurations would be approximately the same. All sections listed in this document are to be considered as common to both methods, unless otherwise noted.
Standard

Exterior Sound Level for Heavy Trucks and Buses
2011-09-12
CURRENT
J366_201109
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
Standard

Sound Level for Truck Cab Interior
2011-09-12
CURRENT
J336_201109
This SAE Recommended Practice describes the equipment and procedure for determining the truck cab interior sound level over the upper half of the engine speed range. This practice applies to motor trucks and truck-tractors and does not include construction and industrial machinery.
Standard

Kingpin Wear Limits—Commercial Trailers and Semitrailers
2001-04-27
HISTORICAL
J2228_200104
This SAE Recommended Practice applies to upper coupler kingpins for commercial trailers and semitrailers conforming to the dimensional requirements of SAE J700 when new and originally installed. The dimensions of SAE J700 are the frame of reference for this document.
Standard

Kingpin Wear Limits - Commercial Trailers and Semitrailers
2011-09-12
CURRENT
J2228_201109
This SAE Recommended Practice applies to upper coupler kingpins for commercial trailers and semitrailers conforming to the dimensional requirements of SAE J700 when new and originally installed. The dimensions of SAE J700 are the frame of reference for this document.
Standard

TRAILER TOW BAR EYE
1984-08-01
HISTORICAL
J847_198408
This SAE Recommended Practice applies to all highway trailer tow bar eye applications.
12Next >Last >>
X