Search Results

Abstract Dynamic stresses exist in parts of a catalyst muffler caused by the vibration of a moving vehicle, and it is important to clarify and predict the vibration response properties for preventing fatigue failures. Assuming a vibration isolating installation in the vehicle frame, the vibration transmissibility and local dynamic stress of the catalyst muffler were examined through a vibration machine. Based on the measured data and by systematically taking vibration theories into consideration, a new prediction method of the vibration modes and parameters was proposed that takes account of vibration isolating and damping. A lumped vibration model with the six-element and one mass point was set up, and the vibration response parameters were analyzed accurately from equations of motion. In the vibration test, resonance peaks from the hanging bracket, rubber bush, and muffler parts were confirmed in three excitation drives, and local stress peaks were coordinate with them as well.

Abstract Reliability analysis of a large-scale system under random dynamic loads can be a very time-consuming task since it requires repeated studies of the system. In many engineering problems, for example, wave loads on an offshore platform, the excitation loads are defined using a power spectral density (PSD) function. For a given PSD function, one needs to generate many time histories to make sure the excitation load is modeled accurately. Global and local approximation methods are available to predict the system response efficiently. Each way has their advantages and shortcomings. The combined approximations (CA) method is an efficient method, which combines the advantages of local and global approximations. This work demonstrates two methodologies that utilize CA to reduce the cost of crude or separable Monte Carlo simulation (MCS) of linear dynamic systems when the excitation loads are defined using PSD functions.

Road vibrations cause fatigue failures in vehicle components and systems. Therefore, reliable and accurate damage and life assessment is crucial to the durability and reliability performances of vehicles, especially at early design stages. However, durability and reliability assessment is difficult not only because of the unknown underlying damage mechanisms, such as crack initiation and crack growth, but also due to the large uncertainties introduced by many factors during operation. How to effectively and accurately assess the damage status and quantitatively measure the uncertainties in a damage evolution process is an important but still unsolved task in engineering probabilistic analysis. In this paper, a new procedure is developed to assess the durability and reliability performance, and characterize the uncertainties of damage evolution of components under constant amplitude loadings.

This paper describes the development and testing of a Dynamic Vibration Absorber to reduce frame beaming vibration in a highway tractor. Frame beaming occurs when the first vertical bending mode of the frame is excited by road or wheel-end inputs. It is primarily a problem for driver comfort. Up until now, few options were available to resolve this problem. The paper will review the phenomenon, design factors affecting a vehicle's sensitivity to frame beaming, and the principles of Dynamic Vibration Absorbers (AKA Tuned Mass Dampers). Finally, the paper will describe simulation and testing that led to the development of an effective vibration absorber as a field fix.

This manuscript provides a review of different types and categorization of the chassis dynamometer systems. The review classifies the chassis dynamometers based on the configuration, type of rollers and the application type. Additionally the manuscript discusses several application examples of the chassis dynamometer including: performance and endurance mileage accumulation tests, fuel efficiency and exhaust emissions, noise, vibration and harshness testing (NVH). Different types of the vehicle attachment system in the dynamometer cell and its influences on the driving force characteristics and the vehicle acoustic signature is also discussed. The text also highlights the impact of the use of the chassis dynamometer as a development platform and its impact on the development process. Examples of using chassis dynamometer as a development platform using Vehicle Hardware In-the-Loop (VHiL) approach including drivability assessment and transmission calibrations are presented.

Vibrations of plates are widely seen in various applications of automobile, aerospace, mechanical and civil engineering. Vibration analysis of plates in medium and high-frequency regions plays an important role in optimal design and safe operation of machines and structures in these applications. Medium and high-frequency vibration analysis of plates is usually performed by using numerical methods. Proposed in this paper is a new analytical solution method for mid- and high-frequency analysis of thin rectangular plates modeled by the Kirchhoff-Love plate theory. In the development, analytical solutions for a class of thin plates are obtained based on a hybrid formulation that combines the Distributed Transfer Function Method (DTFM) and modal expansion. The proposed method, which is an extension of the DTFM for one-dimensional continua, is called the hybrid Distributed Transfer Function Method (hybrid DTFM).

Noise & Vibration refinement of automotive vehicles is becoming important parameter due to its influence on environmental aspect and comfort perceived by occupants. NVH parameters are driving factors in current vehicle design strategy. Drivers comfort is extremely important, and driver’s expectations from commercial and heavy-duty trucks are as good as refined passenger cars. Other trends in commercial vehicle segment such as engine downsizing, weight, cost reduction and meeting stringent emission norms have influenced vehicle design dynamics. These parameters are critical and often contribute to vehicle NVH issues. Considering these new trends in commercial vehicle segment, it becomes challenging for an NVH engineer to provide optimized solutions. NVH issues could be related to the various subsystems such as driveline, axle, transmission steering wheel etc. in the vehicle and its resonant frequencies.

In today’s automobile industry refined NVH performance is a key feature and of high importance governing occupant comfort and overall quality impression of vehicle. In this paper interior noise and vibration measurement is done on one of the light truck and few dominant low frequency noise booms were observed in operation range. Modal analysis was done for the cabin at virtual as well as experimental level and few modes were found close to these noise booms. Vibrations were measured across the cabin mounts and it was found that the isolation of front mounts is not effective at lower frequencies. Taking this as an input, the mount design was modified to shift the natural frequency and hence improve the isolation behavior at the lowest dominant frequency. This was followed by static and dynamic measurement of the mounts at test rig level to characterize the dynamic performance and stiffness conclusion.

Despite numerous research efforts, there is no reliable and widely accepted tool for the prediction of erosion prone material surfaces due to collapse of cavitation bubbles. In the present paper an Erosion Aggressiveness Index (EAI) is proposed, based on the pressure loads which develop on the material surface and the material yield stress. EAI depends on parameters of the liquid quality and includes the fourth power of the maximum bubble radius and the bubble size number density distribution. Both the newly proposed EAI and the Cavitation Aggressiveness Index (CAI), which has been previously proposed by the authors based on the total derivative of pressure at locations of bubble collapse (DP/Dt>0, Dα/Dt<0), are computed for a cavitating flow orifice, for which experimental and numerical results on material erosion have been published. The predicted surface area prone to cavitation damage, as shown by the CAI and EAI indexes, is correlated with the experiments.

The research on the characteristics of vehicle movement is the premise to guarantee the smooth operation of electric vehicles, and it’s also the basis for developing the vehicle ability in depth. Therefore, it’s essential to study on the vehicle movement characteristics. And steering on ramp is a typical working condition for tracked vehicle. Firstly, the kinematics and dynamics of tracked vehicle during the steering process on ramp are analyzed in detail aiming at the problem that it’s complex and difficult to describe the process of steering, and the dynamics model of tracked vehicle is established in the condition of the offset of instantaneous steering center and the sliding of the track and other factors. Second, the relationships between driving force, steering radius and slop are obtained by simulation, and the variation rules of these parameters are analyzed. Finally, the model of steering on ramp is verified using electric tracked vehicle.

This Hydrospace Information Report (HIR) identifies the general environmental considerations for the design, development, evaluation, and testing of advanced surface craft, submersible vehicles, and other marine craft. This HIR provides criteria on the environmental limits within which marine vehicles, related components, and associated equipment should operate satisfactorily and reliably. This HIR is intended for use as a guide for the development of specific environmental requirements to be included in detailed specifications for marine vehicles and associated equipment. Specific requirements are in a state of continual change as our knowledge of the ocean environment increases. The ocean environment varies with location and time. Changes in the ocean environment can occur not only on a seasonal basis but also monthly, weekly, daily, and in some cases even hourly.

Gear rattle noise is a common issue in manual gear transmissions and is often difficult to resolve. This paper discusses a methodology involving development of a simulation model for noise prediction and subsequent design of experiments (DOE) analysis to select optimal design parameters to reduce rattle noise. A one-dimensional torsional vibration simulation model for a tractor driveline was developed and was correlated with experimental measurements. This correlated model was used to calculate the torque variation between the gear pairs based on engine excitations. The standard deviation of this mesh torque was used as a metric and was correlated to noise ratings assigned by experts during experimental evaluation. Using this metric as the response variable, a DOE was conducted to determine the contributing factors and their influence on the rattle noise. Optimal design parameters were selected to achieve target value on the rattle metric.

Several recent product developments for vibration and motion control have needed passive viscous damping, in addition to traditional elastomer-based hysteretic damping, to be successful in their respective applications. In addition to attenuating steady-state vibration, an important function of these recent product developments is to control motion from impulsive or mechanical shock input. Examples are the cab mounts of off-highway vehicles that need damping in the vertical direction to control cab motion from ground input through the vehicle and some torsionally flexible couplings that need damping to control torque spikes from shift shocks or other transient events. In this work, the theoretical damped impulse response quantities of displacement, velocity, acceleration, force, jerk, yank, and jounce are investigated. This work shows that, for certain response quantities, there is a specific magnitude of damping that minimizes response from impulsive or mechanical shock input.

Durability and reliability performance is one of the most important concerns of a recently developed Thermal Regeneration Unit for Exhaust (T.R.U.E-Clean®) for exhaust emission control. Like other ground vehicle systems, the T.R.U.E-Clean® system experiences cyclic loadings due to road vibrations leading to fatigue failure over time. Creep and oxidation cause damage at high temperature conditions which further shortens the life of the system and makes fatigue life assessment even more complex. Great efforts have been made to develop the ability to accurately and quickly assess the durability/reliability of the system in the early development stage. However, reliable and validated simplified engineering methods with rigorous mathematical and physical bases are still urgently needed to accurately manage the margin of safety and decrease the cost, whereas iterative testing is expensive and time consuming.

Fatigue, creep, oxidation, or their combinations have long been recognized as the principal failure mechanisms in many high-temperature applications such as exhaust manifolds and thermal regeneration units used in commercial vehicle aftertreatment systems. Depending on the specific materials, loading, and temperature levels, the role of each damage mechanism may change significantly, ranging from independent development to competing and combined creep-fatigue, fatigue-oxidation, creep-fatigue-oxidation. Several multiple failure mechanisms based material damage models have been developed, and products to resist these failure mechanisms have been designed and produced. However, one of the key challenges posed to design engineers is to find a way to accelerate the durability and reliability tests of auto exhaust in component and system levels and to validate the product design within development cycle to satisfy customer and market's requirements.

Steering wheel vibration is one of the major factors in determining the operator comfort in agricultural tractors. Main sources of steering wheel vibration are engine imbalance, resonance of steering system, lesser damping, road / field induced vibration, etc. The European Council directive 2002/44/EC recommendations are taken as guidelines in this work. Steering vibration study was conducted on various tractor models (40 - 50 kW range) and one tractor was identified for improvement. Upon detailed analysis on that particular tractor, it was found that the resonance of steering system with engine excitation is the root cause for excessive vibration. Various methods to reduce vibration due to resonance were considered, such as shifting the natural frequency away from the second order engine frequency and increasing damping coefficient to reduce the vibration amplitude at resonance. Six different concepts were generated and analyzed using the design assessment matrix.

Abstract Geometric variation stemming from manufacturing can be a limiting factor for the quality and reliability of products. Therefore, manufacturing assessments are increasingly being performed during the early stages of product development. In the aerospace industry, products are complex engineering systems, the development of which require multidisciplinary expertise. In such contexts, there are significant barriers against assessing the effects of geometric variation on the functionality of products. To overcome these barriers, this article introduces a new methodology consisting of a modelling approach linked to a multidisciplinary simulation environment. The modelling approach is based on the parametric point method, which allows point-scanned data to be transferred to parameterised CAD models. In a case study, the methodology is implemented in an industrial setting.

Real-time control systems have continued to advance along with other electronic devices and are now being utilized in the heavy-duty truck industry. These systems are designed to electronically control events as they happen and provide up-to-date diagnostic information, thus increasing the operating efficiency, reliability and safety of the vehicle. Real-time control systems have a potential for many different applications beyond those which are currently being employed in the trucking industry.

Structural attenuation of a running diesel engine measured by a new technique showed a constant value regardless of engine speeds. It was verified by this result that structural attenuation is a physical quantity unique to the structure of each engine and, therefore, a good indicator for evaluation of low noise engine structure. In addition, a hydraulic excitation test rig was devised to measure structural attenuation directly and to make effective use of it for noise reduction. Based on the accurate measurements by the excitation test rig, modal analysis and system simulation were conducted for implementation of countermeasures against noise.

Filtering the road unevenness, i.e. comfortable ride for passengers, and vibration and shock isolation for freight, is one of the main thrusts behind the development of active and semi-active suspensions. For control of these systems, a variety of different schemes, mainly from the linear stochastic control area, have been proposed by researchers: and 1/4-car active and semi-active suspension models are used to simulate these schemes. Besides the main input an exogenous input is also considered, namely a velocity disturbance originating from the road unevenness. In most of the literature in this area, this disturbance is considered as white noise, which it hardly is. This a-priori statistical description of the disturbances, is necessary for using stochastic control techniques. In this paper, a comparison of some of these control schemes is performed.