Search Results

SAE 2011 High Efficiency IC Engines Symposium - Session 4 - Novel Engine Components and Systems. Presenter Neville Jackson, Ricardo plc

SAE 2011 High Efficiency IC Engines Symposium - Session 1- Pathways to High Efficiency. Presenter John E. Dec, Sandia National Laboratories

Exhaust Emission Control: DPF Systems. Presenter Shingo Iwasaki, NGK Insulators, Ltd.

In order to extend the CAI operation range in 4-stroke mode and maximize the benefit of low fuel consumption and emissions in CAI mode, 2-stroke CAI combustion is revived operating in a GDI engine with poppet valves, where the conventional crankcase scavenging is replaced by boosted scavenging. The CAI combustion is achieved through the inherence of the 2-Stroke operation, which is retaining residual gas. A set of flexible hydraulic valve train was installed on the engine to vary the residual gas fraction under the boosting condition. The effects of spark timing, intake pressure and short-circuiting on 2-stroke CAI combustion and its emissions are investigated and discussed in this paper. Results show the engine could be controlled to achieve CAI operation over a wide range of engine speed and load in the 2-stroke mode because of the flexibility of the electro-hydraulic valvetrain system. Presenter Yan Zhang, Brunel University

High-load HCCI combustion has recently been demonstrated with conventional gasoline using intake pressure boosting. The key is to control the high combustion heat release rates (HRR) by using combustion timing retard and mixture stratification. However, at naturally aspirated and moderately boosted conditions, these techniques did not work well due to the low autoignition reactivity of conventional gasoline at these conditions. This work studies a low-octane distillate fuel with similar volatility to gasoline, termed Hydrobate, for its potential in HCCI engine combustion at naturally aspirated and low-range boosted conditions. The HCCI combustion with fully premixed and partially stratified charges was examined at intake pressures (Pin) from 100 to 180 kPa and constant intake temperature (60�C) and engine speed (1200 rpm).

This technical paper collection contains 26 papers on HCCI combustion published from the 2011 Powertrain Fuels and Lubricants Conference.

The 8 technical papers in this collection focus on kinetically controlled combustion. Experimental and simulation studies pertaining to various means of controlling combustion are welcome. Examples are research studies dealing with temperature and composition distribution inside the cylinder and their impact on heat release process. Studies clarifying the role of fuel physical and chemical properties in autoignition are also welcome.

This technical paper collection covers papers describing experiments and test data, simulation results focused on applications, fuel/additive effects, combustion control, and mode change. Papers with an emphasis on the modeling aspects of combustion are also included.

The papers in this collection cover recent advances in research, development and engineering of hybrid, plug-in hybrid, and electric powertrains and architectures with particular emphasis on new and near-production technologies.

Classical HCCI combustion with temperature controlling combustion onset and only a modest effect of fuel injection. Papers describing experiments and test data, simulation results focused on applications, fuel/additive effects, combustion control, and mode change are invited are included in this collection.

Classical HCCI combustion with temperature controlling combustion onset and only a modest effect of fuel injection. Papers describing experiments and test data, simulation results focused on applications, fuel/additive effects, combustion control, and mode change are part of this collection.

Classical HCCI combustion with temperature controlling combustion onset and only a modest effect of fuel injection. Papers describing experiments and test data, simulation results focused on applications, fuel/additive effects, combustion control, and mode change are invited are included in this collection.

Abstract The preliminary gas turbine combustor design process uses a huge amount of empirical correlations to achieve more optimized designs. Combustion efficiency, in relation to the basic dimensions of the combustor, is one of the most critical performance parameters. In this study, semi-empirical correlations for combustion efficiencies are examined and correlation coefficients have been revised using an experimental air-blasted tubular combustor that uses JP8 kerosene aviation fuel. Besides, droplet diameter and effective evaporation constant parameters have been investigated for different operating conditions. In the study, it is observed that increased air velocity significantly improves the atomization process and decreases droplet diameters, while increasing the mass flow rate has a positive effect on the atomization—the relative air velocity in the air-blast atomizer increases and the fuel droplets become finer.

The papers in this collection focuses on technologies such as advanced and partially mixed combustion, cooled EGR boosting, ignition and direct injection technologies, pressure boosting, intelligent combustion, thermal efficiency, fully variable valvetrains, and other new and developing technologies.

Computational modeling and analysis of Reactivity Controlled Compression Ignition (RCCI) combustion. Papers focus on analyzing and improving RCCI combustion using novel injection strategies, combustion chamber designs, and fueling combinations.

The 26 papers in this technical paper collection focuses on kinetically controlled combustion including, HCCI, PCCI, CAR, RCCI, etc.

The purpose of this SAE Standard is to provide a standardized test procedure for measuring the fuel consumption of spark ignited engines in the range of 225-999cc used in the consumer and commercial turf industry. The load points and associated fuel consumption rates will be measured as the engine operates on the engine speed governor, reflecting how the user will operate the equipment. The fuel consumption calculated in gallons of useage per hour will be derived from a specified engine speed and load map to be communicated universally to end users.

Premixed Charge Compression Ignition (PCCI), a Low Temperature Combustion (LTC) strategy for diesel engines is of increasing interest due to its potential to simultaneously reduce soot and NOx emissions. However, the influence of mixture preparation on combustion phasing and heat release rate in LTC is not fully understood. In the present study, the influence of injection timing on mixture preparation, combustion and emissions in PCCI mode is investigated by experimental and computational methods. A sequential coupling approach of 3D CFD with a Stochastic Reactor Model (SRM) is used to simulate the PCCI engine. The SRM accounts for detailed chemical kinetics, convective heat transfer and turbulent micro-mixing. In this integrated approach, the temperature-equivalence ratio statistics obtained using KIVA 3V are mapped onto the stochastic particle ensemble used in the SRM.

The effect that thermally and compositionally stratified flowfields have on the spatial progression of iso-octane-fueled homogeneous charge compression ignition (HCCI) combustion were directly observed using highspeed chemiluminescence imaging. The stratified in-cylinder conditions were produced by independently feeding the intake valves of a four-valve engine with thermally and compositionally different mixtures of air, vaporized fuel, and argon. Results obtained under homogeneous conditions, acquired for comparison to stratified operation, showed a small natural progression of the combustion from the intake side to the exhaust side of the engine, a presumed result of natural thermal stratification created from heat transfer between the in-cylinder gases and the cylinder walls. Large differences in the spatial progression of the HCCI combustion were observed under stratified operating conditions.

The mixing and combustion processes of short double Diesel injections are investigated by optical diagnostics. A single hole Common Rail Diesel injector allowing high injection pressure up to 120MPa is used. The spray is observed in a high pressure, high temperature cell that reproduces the thermodynamic conditions which exist in the combustion chamber of a Diesel engine during injection. Three configurations are studied: a single short injection serving as a reference case and two double short injections with short and long dwell time (time between the injections). Several optical diagnostics were performed successively. The mixing process is studied by normalized Laser Induced Exciplex Fluorescence giving access to the vapor fuel concentration fields. In addition, the flow fields both inside and outside the jets are characterized by Particle Imaging Velocimetry.