Search Results

The exhaust system design and development need to be more flexible and easily adaptable for the requirement of dynamic changes to meet the upcoming emission and noise regulations. Durability of exhaust system components are evaluated through conventional bending moment testing using specified standard load conditions. Road load re-production test is an improvement of the conventional approach to predict component weld durability. It involves the systematic and sequential process of acquiring road load data such as sensor instrumentation, strain measurement at the test track, data processing and input to Bi-Ax testing. S/N Curve testing is introduced recently as an alternate method to minimize the use of road load reproduction testing. It involves prediction of rough force using transient response analysis followed by Bi-Ax testing for the derived high and low load forces to meet the target number of cycles to failure.

Tube bends are critical in an exhaust system. The acceptability of tube bends is based on the induced level of shape imperfections considered. An analysis is presented for the performance tuning of the genetic algorithm including the importance of raw material selection, ovality and elongation property. This study is an attempt to analyze the ovality effect of STAC 60/60 material. CAE tools are essential to exploit the design of experiments and find out the optimum values of the design parameters in comparison with full factorial designs. Especially the effects of materials, dimensions and geometry shape of the ultimate strength were discussed by both CAE and experiments. The ultimate strength of steel tube was evaluated at least 20-30% as a local strain independent of the materials. The dependency of ultimate bending angle on original centre angle of the tube bend was clarified.

Typically, the maximum converter skin temperature occurs when the catalytic converter is in the cool down process after the engine is shut-off. This phenomenon is called temperature soaking. This paper proposes a numerical method to simulate this process. The converter skin temperatures vs. time are predicted for the converter cool down process. The soaking phenomenon is observed and the maximum temperature is determined. Temperatures are also predicted for the exhaust gas, substrate, mounting mat and shell of the converter assembly. The numerical results are validated with measurements, and an acceptable correlation is achieved. This study focuses on converters with ceramic substrates; however, this methodology can also be used for converters with metallic substrates.

Single seam stuffed converters are often used to house ceramic substrates due to the simplicity and low tooling cost of the canning process. However, stuffing thinwall substrates requires careful GBD (gap bulk density) control because of their low isostatic strengths. Statistical simulation results indicate that the stuffing process can be performed within the required GBD range of 0.8 to 1.2 g/cm3 using vermiculite mats with the current tolerance specifications. A nominal value of 0.925 g/cm3 is recommended to minimize substrate breakage. Experimental results show that prototypes can be built with a GBD accuracy of 0.05 g/cm3. This paper describes the requirements needed to design and validate single seam stuffed converters.

Automotive exhaust system components are exposed to many types of vibrations, from simple sinusoidal to maximum random excitations. Computer-Aided engineering (CAE) plays an inevitable role in design and validation of hot vibration shaker assembly. Key Life Test (KLT), an accelerated hot vibration durability test, is established to demonstrate the robustness of a catalytic converter. The conditions are chosen such a way that the parts which passes key life test will always pass in the field, whereas the parts which fail in the key life test need not necessarily fail in the field. The hot end system and the test assembly should survive in these aggressive targeted conditions. The test fixture should be much more robust than the components that it should not fail even if the components fail. This paper reveals the computational methodology adopted to address the design, development and validation of the test assembly.

While advanced automotive system assemblies contribute greater value to automobile safety, reliability, emission/noise performance and comfort, they are also generating higher temperatures that can reduce the functionality and reliability of the system over time. Thermal management and proper insulation are extremely important and highly demanding for the functioning of BSVI and RDE vehicles. Frugal engineering is mandatory to develop heat shield in the exhaust system with minimum heat loss. Heat shield design parameters such as insulation material type, insulation material composition, insulation thickness, insulation density, air gap thickness and outer layer material are studied for their influences on skin temperature using mathematical calculation, CFD simulation and measurement. Simulation results are comparable to that of the test results within 10% deviation.