Search Results

Hydrogen spark-ignition (SI) engines based on direct-injection (DI) promise significant advantages in terms of thermal efficiency and power output, as well as a means of overcoming problems related to knocking, backfiring, and pre-ignition. In a DI hydrogen engine, the fuel/air mixture is formed by injecting a jet of hydrogen into the air inside the combustion chamber. An Ar-ion laser beam was used as a light source to visualize the hydrogen jet in a constant-volume chamber. This allowed us to study the structure of the jet in addition to other physical processes resulting from hydrogen gas injection. Combustion experiments were conducted in a single-cylinder SI optical research engine equipped with a DI system to detect the early kernel growth assisted by the spark, as well as flame propagation. Various equivalence ratios and fuel injection timings were analyzed to identify the effects on combustion.

Homogeneous charge compression ignition (HCCI), has the potential to improve the fuel economy and to reduce NOx emission significantly. Spark plug in SI engine and fuel injector in diesel engine can be used directly to control the start of combustion and the combustion period. However, the combustion of HCCI engine is controlled by the chemical kinetic mainly due to the temperature histories in the cylinder. Therefore the combustion process of HCCI engine cannot be directly controlled. Ion sensors such as a spark plug or a gasket are useful to detect the combustion information in production engines. In this study, the ion current was measured in an HCCI engine with the heated charge mixture of fuel and air without EGR when the charge temperature, equivalence ratio and fuel were varied. Simultaneously in-cylinder pressure was measured and the rate of heat release was calculated. The relationship between the rate of heat release and the ion current is mainly discussed.

In this study, residual gas fraction measurements in a spark-ignition engine were carried out using an optical sensor installed in the spark plug with infrared absorption method. The residual gas fraction inside engine cylinder is proportional to the CO2 concentration. Infrared absorption method was applied and an infrared lamp and optical filter (center wavelength: around 4.3 μm) that coincides with the absorption lines of CO2 was used as a light source.The molar absorption coefficient of CO2 is discussed and compared to results in the HITRAN database. The effect of water vapor absorption doesn't affect the absorption of CO2. The absorption characteristics of CO2 were determined in advance using a constant volume vessel. Molar absorption coefficient depends on the CO2 concentration and ambient pressure and temperature, and wavelength of absorption line.

Investigation of knocking combustion in a hydrogen spark-ignition engine is one of the major challenges for future vehicle development. The knock phenomenon in a Spark-Ignition (SI) engine is caused by autoignition of the unburned gas ahead of the flame. The explosive combustion of the end-gas creates a pressure wave that leads to damage of the cylinder wall and the piston head of the engine. We observed autoignition in the end-gas region due to compression by the propagating flame front using a high-speed colour video camera through the optically accessible cylindrical quartz window on the top of the cylinder head. Moreover, a high-speed monochrome video camera operating at a speed of 250, 000 frame/s was used to measure the pressure wave propagation. The goal of this research was to improve our ability to describe the effect of the autoignition process on the end-gas and propagating pressure wave during knocking combustion with the help of a high-speed video camera.

In this study, fuel concentration measurements in a spark-ignition (SI) engine with ethanol blended gasoline were carried out using an optical sensor installed in the spark plug with laser infrared absorption technique. The spark plug sensor for in-situ fuel concentration measurement was applied to a port injected SI engine. The molar absorption coefficients of ethanol blended gasoline were determined for various pressures and temperatures in advance using a constant volume vessel with electric heating system. Ethanol blended gasoline with high volumetric ratios shows lower molar absorption coefficients due to lower molar absorption coefficients of ethanol. The molar absorption coefficients of ethanol blended gasoline can be estimated by considering the molar fraction of each component.

The several burning models based on the wrinkled laminar flame concept had been proposed and applied to the turbulent premixed flame in a spark ignition engine. Fractal burning model is one of the flamelet burning models. However the formulations of fractal characteristics such as fractal dimension, inner cutoff scale and outer cutoff scale weren't established. These formulations based on the results of the fractal analysis in a constant volume vessel and a spark ignition engine were proposed in this study. The fractal dimension is expressed as a function of non-dimensional turbulence intensity and the density of mixture. Non-dimensional inner cutoff scale is expressed a function of Karlovitz number. Outer cutoff scale is equal to the flame radius. Finally the quasidimensional model for turbulent combustion was performed by using the fractal burning model with our formulations.

It is well known that the wavelet transform is a useful time-frequency analysis method for an unsteady signal and major attention has been focused on the selection of the mother wavelet (MW) because the MW plays an important role in the wavelet transform. In this study, we analyze the pressure signal in a spark-ignition engine and the vibration of the engine block measured by a knock sensor under the knocking conditions when knocking is caused. We then propose a new method of the knocking detection that utilizes the knocking signal measured with a knock sensor as a MW. We call this method the Instantaneous Correlation Method (ICM). The degree of similarity between the MW and the vibration of the engine block was judged and only the knocking signal from the vibration of the engine block was extracted. The results obtained here show that the method proposed in this study is useful for knocking detection even if the engine speed is very high of 6000rpm.

It is important to develop the technique for measuring the cycle-to-cycle variation of combustion in order to reduce the fuel consumption of the commercial spark ignition engine. In previous study, we had proposed using the spark plug as an ion probe to measure the appearance time of maximum pressure under the lean mixture conditions of the research engine. In this paper the combustion diagnostics for the commercial engine was performed using the spark plug as an ion probe. Under idling conditions the ion current often appeared during the exhaust process. This ion current is dominated by the flame contact area and the flame velocity. In this case there is good correlation between the characteristic value of the ion current and the indicated mean effective pressure (IMEP). Finally using the spark plug as an ion probe can detect the combustion quality under conditions with large cyclic variation.

This study measured the fuel concentration near a spark plug using a laser infrared absorption method. An IR spark plug sensor with a double-pass measurement length was developed. A He-Ne laser with a wavelength of 3.392 μm, which coincides with the absorption line of hydrocarbons, was used as the light source. In order to confirm the measurement accuracy, the concentrations of a methane-air mixture were measured in a compression-expansion engine. Then, the IR spark plug sensor was used for measurements in a 4-stroke spark-ignition engine fuelled with isooctane. The air/fuel ratio measured using this system clearly agreed with the mean air/fuel ratio.

Homogeneous Charge Compression Ignition (HCCI) combustion with dimethyl ether has been carried out in a single cylinder engine with a transparent piston. The engine was operated at 800 rpm with a wide-open throttle. The intake-premixed mixture was preheated with an electric heater to promote auto-ignition. HCCI combustion with dimethyl ether indicates multi-stage heat releases. Investigations were conducted with visualization of combustion in the cylinder and detailed and temporal spectroscopic measurements using spectrometer. In order to understand reaction mechanism of auto-ignition and combustion mechanism in HCCI engine, spectrum analysis of chemiluminescence was carried out.

A new technique for combustion diagnostics of a spark ignition engine was developed. In this method the ion sensor with the circular configuration was installed into the cylinder head gasket. This sensor is expected to be applied for production engine. The signal measured by the ion sensor was similar with that of cylinder pressure. The peak timing of ion current was consistent with the peak timing of pressure. There was a strong correlation between IMEP and the peak timing of ion current. This sensor is available to detect combustion quality in a spark ignition engine.

Hydrogen spark-ignition (SI) engines based on direct-injection (DI) have been investigated because of their potential for high thermal efficiency and solving the problems related to knocking, backfiring, and pre-ignition. Wide range flammability limits in hydrogen engine enable smooth engine operation for a very lean mixture with low NOX. However, a too lean mixture may increase ignition delay and causes severe cyclic variations. There is a possibility that the turbulence occurred during injection of fuel surround the spark plug in the combustion chamber is major contributor to this phenomenon. To overcome this problem, a better understanding of the spark discharge and spark ignition during transient hydrogen jet is necessary. Therefore, it is very important to study an effect of local equivalence ratio and behavior of spark discharge in SI engine. This paper describes a mixing process of hydrogen jet using spark-induced breakdown spectroscopy (SIBS) in a constant volume vessel.

This paper describes the development and application of a spark plug sensor using a 3.392 μm infrared absorption technique to quantify the instantaneous gasoline concentration near the spark plug. We developed an in situ laser infrared absorption method using a spark plug sensor and a 3.392 μm He-Ne laser as the light source; this wavelength coincides with the absorption line of hydrocarbons. First, we established a database of the molar absorption coefficients of premium gasoline at different pressures and temperatures, and determined that the coefficient decreased with increasing pressure above atmospheric pressure. We then demonstrated a procedure for measuring the gasoline concentration accurately using the infrared absorption technique. The history of the molar absorption coefficient of premium gasoline during the experiment was obtained from the established database using measured in-cylinder pressures and temperatures estimated by taking the residual gas into consideration.

A small Cassegrain optics sensor was developed to measure local chemiluminescence spectra and the local chemiluminescence intensities of OH*, CH*, and C2* in a four-stroke spark-ignition (SI) engine in order to investigate the propagation characteristics of the turbulent premixed flame. The small Cassegrain optics sensor was an M5 type that could be installed in place of a pressure transducer. The measurements could be used to estimate the flame propagation speed, burning zone thickness, and local air/fuel (A/F) ratio for each cycle. The specifications of the small Cassegrain optics sensor were the same as those used for previous engine measurements. In this paper, measurements were made of several A/F ratios using gasoline to fuel the model engine. The performances of two Cassegrain optics sensors were compared to demonstrate the advantages of the new small sensor by measuring the local chemiluminescence intensities of a turbulent premixed flame in the model engine.

A heterodyne interferometry system with a fiber-optic sensor was developed to measure the temperature history of unburned gas in a spark-ignition engine. A polarization-preserving fiber and metal mirror were used as the fiber-optic sensor to deliver the test beam to and from the measurement region. This fiber-optic sensor can be assembled in an engine cylinder head without a lot of improvements of an actual engine. Adjustment system in the sensor was revised to face the distributed index lens with metal mirror. Before the flame arrived at the developed fiber-optic sensor, measured temperature was almost same with the temperature history after the spark, assuming that the process that changes the unburned gas is adiabatic. In situ unburned gas temperature measurements before knocking in a commercially produced SI engine can be carried out using developed fiber-optic heterodyne interferometry system.

The purpose of this study was to characterize the air/fuel ratio (AFR) of turbulent premixed flames in a spark-ignition (SI) engine. We developed a spark plug sensor with an optical fiber to detect the chemiluminescence spectra, specifically the intensity of the spectral lines related to OH*, CH*, and C2* free radicals. The sensor was composed of a sapphire window and optical fiber and is applicable to automobile SI engines. Measurements of the chemiluminescence intensity from OH*, CH*, and C2* radicals were obtained in turbulent premixed flames with a propane-air mixture for different AFRs in a compression-expansion machine (CEM). The performance of the spark plug sensor was compared with a Cassegrain reflector using an intensified charge-coupled device. The results showed good agreement with measurements obtained using the Cassegrain reflector. The spark plug sensor was shown to be useful for measuring chemiluminescence of turbulent premixed flames in an SI engine.

In order to reduce the exhaust emission and the fuel consumption in a spark ignition engine, the combustion diagnostics had been developed. However, there are few sensors which can detect the combustion quality for the individual cycle and cylinder in production engines. In previous study, the new technique using a gasket ion sensor for measuring the combustion quality has been proposed. In present study, the flame propagation pattern in a spark ignition engine was detected by using a gasket ion sensor with a circular electrode. The waveforms of ion current obtained from a circular ion sensor were compared with the flame propagation pattern obtained from multiple ion sensors. When the mixture was ignited in offset center of the cylinder, the flame propagation pattern was distorted from the spherical pattern. Then the waveforms of ion current from the circular ion sensor were varied from the waveform for a center ignition.

An investigation was made into two approaches to air-fuel mixture formation in direct injection SI engines in which charge stratification is controlled by swirl or tumble gas motions, respectively. Particle image velocimetry (PIV), laser-induced fluorescence (LIF) and air-fuel ratio measurement by infrared absorption were used to analyze fuel transport from the fuel injector to the spark plug and the fuel vaporization process. The results obtained were then compared with measured data as to combustion stability. As a result, the reason why the effects of injection timing on combustion stability were different between the two approaches was made clear from the standpoint of the mixture formation process.

A turbulent entrainment model is considered to be reasonable for the combustion in a spark-ignition engine. For this kind of model, it is important to estimate the turbulence characteristics, turbulent burning velocity, flame surface area and several empirical constants. Nevertheless, the examination of these values have not been examined sufficiently. In this study, a combustion model was proposed, and initiation of flame propagation, burning process of an eddy, scale of turbulence and turbulent burning velocity were discussed in detail. This model was examined under various conditions of engine speed (600-1200rpm), compression ratio (3.2-4.8) and ignition timing. The calculation results of mass fraction burned, burn rate and burn duration were in good agreement with the experimental ones. It was found that the concept of such a turbulent entrainment model was valid for predicting the combustion in a spark-ignition engine.

The structures of the turbulent premixed flame in the engine cylinder under lean burn conditions were investigated using ion probe method. The flow fields were measured with an LDA for two tumble ratios and two compression ratios. And ion-current signal was analyzed to discuss the interaction between the turbulence and the flame structure. The effects of turbulence and equivalence ratio on the characteristic values of the turbulent flame, that is to say number of ion-current peaks, thickness of flame front and thickness of burning zone of the flamelet, were investigated. In normal combustion, the structure of the turbulent flame front is almost the same as the laminar flame. In the lean limit, the flamelet is broken and stretched and then the structure may change.