Search Results

Engine bearings today are operating under very harsh conditions. Consequently, a wear propagates for a short time and a fatigue sometimes occurs on the bearings. In present study, on the rig test machine, the operating conditions of engine bearing were simulated to reproduce the bearing damage. The bearing wear was measured until the fatigue crack occurred. The bearing wear increased at the edges of the bearing length and the crack also was observed near the edges. The experimental results were compared to the calculated results based on the elastohydrodynamic lubrication (EHL) theory. The correlations between the bearing damage and the bearing performances by the theoretical analysis were investigated.

The mechanical loss reduction of the bearing reduces the fuel consumption of the engine, which can help realize a sustainable society. Thus, a bearing friction reduction technique has been studied. There have been many studies related to friction-reduction techniques for mixing and boundary lubrication. However, there are few studies on hydrodynamic lubrication, and the main methods have been related to changing the low-viscosity oil and bearing size. In driving passenger cars in urban areas, the lubricant condition of the engine bearings is largely dependent on hydrodynamic lubrication. Therefore, the power loss under this operating condition cannot be ignored. In this study, the reduction of the friction loss under hydrodynamic lubrication was focused. A method for reducing the shear resistance of oil was examined and its effect was confirmed through experiments and calculations.

With increased awareness of environmental issues and regulations, developments for recent automotive engines are progressing towards engines with low fuel consumption. Due to these changes, automotive engine bearings are increasingly used in harsher environments, with higher loading and corresponding wear. From this background, resin overlays, where solid lubricant is dispersed in a resin binder, are being developed. Resin overlays show excellent sliding properties under boundary lubrication conditions, and are known to have superior wear and fatigue resistance compared with conventional aluminium based bearings. However, while conventional resin overlay bearings display excellent sliding properties, they tend to have inferior seizure resistance compared to Al-Sn-Si alloy bearings. In this study, by optimizing the strength of the resin overlay layer with addition of calcium carbonate particles, a resin overlay with equal wear resistance but improved seizure resistance was developed.

The advent of high-performance, compact, and lightweight engines in recent years brings forth a tendency to increase the load for engine bearings and demands on producing even higher levels of durability and reliability in bearing products against fatigue, seizure, wear, and corrosion. Based on the perspective of extending the bearing life, the authors have studied the problems that are encountered with the current three layer copper-lead alloy bearings after their overlay has worn out. Then, we studied the issues of lowered seizure resistance that results from the exposure of the nickel barrier, and of deficient corrosion resistance that results from the exposure of the bearing alloy. In order to improve upon these areas, we focused on diffusion phenomenon of overlay elements without the nickel barrier and also studied the feasibility of creating engine bearings whose alloy composition has been partially modified.

The possibility of predicting engine bearing durability by elastohydrodynamic lubrication (EHL) calculations was investigated with the aim of being able to improve durability efficiently without conducting numerous confirmation tests. This study focused on the connecting rod big-end bearing of an automotive engine. The mechanisms of wear and fatigue, which determine bearing durability, were estimated by comparing the results of EHL analysis and experimental data. This comparison showed the possibility of predicting the wear amount and the occurrence of fatigue by calculation.

Recently, automotive engines have been operating under harsh conditions of high-power, low viscosity oil and increase of start-stop (e.g. idling stop). In plain bearing used within engine, as oil film thickness decreases, the frequency of direct contacts on the sliding surfaces between the shaft and the bearing are gradually increasing. In fact, the plain bearings for engines would tend to be used under mixed lubrication and the contacts of the surface roughness asperities sometimes occur between the shaft and the bearing. As a result, the bearing wear on the sliding surfaces is accelerated by the contacts of the roughness asperities. In order to predict the bearing performance exactly, it is very important to understand the change progress of the geometric shape of sliding surfaces caused by the wear.

Seat vibration when a vehicle is idling or in motion is an issue in automobile development. In order to reduce this vibration, dynamic damper or inertia mass is widely used. These countermeasures increases vehicle's weight and causes bad fuel-efficiency. Some new ways to reduce the vibration without weight increase are needed. One of that is the floating seat. Seat vibration has been reduced by controlling seat resonance frequencies. In order to control resonance frequency, the structures of the seat-mounting unit are replaced with floating structures using rubber bushings. It was demonstrated that partially replacing the mounting unit with floating structures makes it possible to control the resonance frequencies of the entire seat. The issue of balancing vibration reduction with strength and durability and crash safety performance caused by the fitting of rubber bushings to the seat-mounting unit was addressed using stopper structures optimized for each type of input.

A newly developed bearing is a lead-free aluminum alloy bearing with low frictional layer which consists of molybdenum disulfide in thicknesses of sub-micron levels on the bearing surface without required binders such as resin. The new bearing had a 50% lower static friction coefficient compared to the conventional aluminum alloy bearing, and exhibited comparable anti-seizure property and fatigue strength to the conventional bearing by evaluation of rig tests. These rig tests verified that the new bearing showed excellent frictional reduction properties. This paper describes details and performances of this newly developed bearing.

This study developed technology for simultaneously welding heterogeneous resin tubes in order to weld and integrate resin tubes with two different specifications (low temperature and high temperature). The aim of integration was cost and weight reduction. The cost reduction due to reducing the number of parts exceeded the increase in material cost due to a change to resin materials. Base material fracture of the resin tubes was set as the breaking format condition, and the welding parameters of the joint part rotations and the friction time between the joint part and the resin tubes were specified as the weld strength judgment standard. In addition, the fused thickness determined by observing the cross-section after welding was specified as the weld quality judgment standard. The range over which weld boundary peeling does not occur and weld strength is manifest was clarified by controlling the welding parameters and the fused thickness.

Nowadays, Bismuth (Bi) is being applied as an overlay material for engine bearings instead of Lead (Pb) which is an environmentally harmful material. Bi overlay has already been a solid performer in some automotive engine sectors due to its superior load carrying capacity and good robustness characteristic which are necessary to maintain its longevity during the lifetime of engines. The replacement is also seen on relatively larger size engines, such as Trucks and Off-highway heavy duty applications. Basically, these applications require higher power output than passenger cars, and the expected component lifecycle becomes longer. Though Bi has similar material characteristic to traditional Pb, it becomes challenging for the material alone to satisfy these requirements. Polymer overlay is known for its superior anti-wear performance and longer lifetime due to less adhesion against a steel counterpart than metallic materials (included Bi).

The superior formability and local ductility of the emerging class of third generation of advanced high-strength steels (3rd Gen AHSS) compared to their conventional counterparts of the same strength level offer significant advantages for automotive lightweighting and enhanced crash performance. Nevertheless, studies on the material behavior of 3rd Gen AHSS have been limited and there is some uncertainty surrounding the applicability of developed methodologies for conventional dual-phase (DP) steels to this new class of AHSS. The present paper provides a comprehensive study on the quasi-static and dynamic constitutive behavior, formability characterization and prediction, and the fracture behavior of two commercial 3rd Gen AHSS with an ultimate strength of 1180 MPa that will be contrasted with a conventional DP1180. The hardening response to large strain levels was determined experimentally using tensile and shear tests and then validated with 3-D simulations of tensile tests.

The SAE Fuel Cell Vehicle (FCV) Safety Working Group has been addressing FCV safety for over 9 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable as a Recommended Practice for FCV development with regard to the identification of hazards and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. SAE J2578 is currently being revised so that it will continue to be relevant as FCV development moves forward. For example, test methods were refined to verify the acceptability of hydrogen discharges when parking in residential garages and commercial structures and after crash tests prescribed by government regulation, and electrical requirements were updated to reflect the complexities of modern electrical circuits which interconnect both AC and DC circuits to improve efficiency and reduce cost.

The SAE FCV Safety Working Group has been addressing fuel cell vehicle (FCV) safety for over 8 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable to FCV development with regard to the identification of hazards and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. J2578 is currently being updated to clarify and update requirements so that it will continue to be relevant and useful in the future. An update to SAE J1766 for post-crash electrical safety was also published to reflect unique aspects of FCVs and to harmonize electrical requirements with international standards. In addition to revising SAE J2578 and J1766, the Working Group is also developing a new Technical Information Report (TIR) for vehicular hydrogen systems (SAE J2579).

The SAE Fuel Cell Vehicle (FCV) Safety Working Group has been addressing FCV safety for over 10 years. The initial document, SAE J2578, was published in 2002. SAE J2578 has been valuable as a Recommended Practice for FCV development with regard to the identification of hazards associated with the integration of hydrogen and electrical systems onto the vehicle and the definition of countermeasures to mitigate these hazards such that FCVs can be operated in the same manner as conventional gasoline internal combustion engine (ICE)-powered vehicles. An update to SAE J1766 for post-crash electrical safety was also published in 2008 to reflect unique aspects of FCVs and to harmonize electrical requirements with international standards. In addition to SAE J2578 and J1766, the SAE FCV Safety Working Group also developed a Technical Information Report (TIR) for vehicular hydrogen systems (SAE J2579).

Recently, as for the rod guide bush bearing materials for shock absorbers, lower friction and the improvement of durability are required along with ride quality and longer life of automobile. Usually, lead is contained in bearing materials. However, the addition of the lead in bearing material is being restricted from the earth environmental problem. Bearing materials for shock absorbers are composite material consists of steel backing and covered with polymer surface layer. This basic material structure hasn't been changed till now, though it has been improved by changing its components and compositions based on the customer's requirement. Bearing material with both lower friction and excellent wear resistance has been developed in this study.

Recently, there has been a tendency of high power and high speed in automotive engines. In addition they have been also required high reliability. And engine bearings have been required to be advanced in wear resistance as well as seizure resistance. Therefore, copper-lead alloy bearings with overlay, which have better seizure resistance, have been widely used for high speed engines up to the present. But it becomes very important for them to advance the overlay wear resistance. In this paper, the composite overlay is mainly researched to improve wear resistance regarding kind of hard particles and their amounts in the overlay.

In recent years, the removal of lead (Pb), which is an environmentally hazardous material often used in bearings for automotive engines, has been continuously promoted. Bismuth (Bi) is attracting attention as a substitute for lead, and it is currently being used mainly for passenger cars and trucks as a lead replacement. However, lead has not been replaced for motorcycles where the bearings are exposed to high temperatures at high rotation speeds, and trucks and generators where high loading capacity, long lifetime and good corrosion resistance are required. It has been difficult to achieve both high load and corrosion resistant for a bearing overlay material. The purpose of this development is to improve the corrosion resistance and fatigue resistance of bismuth overlay by developing a bismuth- antimony alloy overlay in which antimony (Sb) is added to the bismuth matrix.

Recent automotive engine developments have made great progress in protecting the global environment and in meeting exhaust gas regulations and fuel economy regulations. As a result, engine bearings tend to be used under severe conditions such as higher specific load onto the bearings and with low viscosity of lubricating oil. Aluminum alloy bearings are widely adopted as main bearings and connecting rod bearings in gasoline and diesel engines for passenger cars, and generally Al-Sn-Si alloy bearings without an additional overlay are used. Although these Al-Sn-Si alloy bearings have good anti-seizure properties and excellent running-in-properties, their material strength under high temperature conditions is not sufficient because of the low melting point of Sn phase contained in the alloy, and they could potentially result in damage to the bearing as seizure and fatigue under these conditions. In such cases, Cu-Pb-Sn alloy bearings with lead-based overlay are usually applied.

Composite bearings of PTFE as the base material have been widely used for automotive parts. However, in recent years, due to downsizing, faster sliding speeds, and tendency to increase the bearing load with high performance, particularly for boundary lubrication conditions, the PTFE-based composite bearing is often worn, making it difficult to apply to some applications. A high strength polymer was selected as an alternative to PTFE base material, and the mechanical properties and performance in a start-stop test, reciprocating sliding test and seizure test were evaluated. Focusing on the characteristics of high strength, by applying a PEEK resin, in each evaluation, it was confirmed that superior performance was achieved compared with a conventional PTFE based composite bearing. Presenter Yohei Takada, Daido Metal Co., Ltd.

Composite bearings of PTFE as the base material have been widely used for automotive parts. However, in recent years, due to downsizing, faster sliding speeds, and tendency to increase the bearing load with high performance, particularly for boundary lubrication conditions, the PTFE-based composite bearing is often worn, making it difficult to apply to some applications. A high strength polymer was selected as an alternative to PTFE base material, and the mechanical properties and performance in a start-stop test, reciprocating sliding test and seizure test were evaluated. Focusing on the characteristics of high strength, by applying a PEEK resin, in each evaluation, it was confirmed that superior performance was achieved compared with a conventional PTFE based composite bearing.